Hostname: page-component-586b7cd67f-dlnhk Total loading time: 0 Render date: 2024-11-24T14:41:08.141Z Has data issue: false hasContentIssue false
  • English
  • Français

Forging of Steam Turbine Blades with an Fe3Al-based Alloy

Published online by Cambridge University Press:  01 February 2011

Peter Janschek ,
Knut Bauer-Partenheimer ,
Ronny Krein ,
Pavel Hanus  and
M. Palm
Peter Janschek
Affiliation:
[email protected], Leistritz Turbinenkomponenten Remscheid GmbH, Remscheid, Germany
Knut Bauer-Partenheimer
Affiliation:
[email protected], Leistritz Turbinenkomponenten Remscheid GmbH, Remscheid, Germany
Ronny Krein
Affiliation:
[email protected], Max-Planck-Institut für Eisenforschung GmbH, Düsseldorf, Germany
Pavel Hanus
Affiliation:
[email protected], Max-Planck-Institut für Eisenforschung GmbH, Düsseldorf, Germany
M. Palm
Affiliation:
Max-Planck-Institut für Eisenforschung GmbH, Max-Planck-Strasse 1, D-40237 Düsseldorf, Germany
Get access

Abstract

The forging capabilities of two high-strength Fe3Al-based alloys have been evaluated. Based on these results one alloy has been used for forging steam turbine blades. Blades of about 600 mm length were successfully forged by a standard procedure otherwise employed for forging of 9-12 wt.% Cr steels. The forged steam turbine blades showed very good form filling, no pores and smooth surfaces. The blades were finished by cutting and grinding by standard procedures. The microstructure consists out of a Fe3Al matrix with additional Laves phase which predominantly precipitated on grain boundaries. The large Fe3Al grains in the cast precursors did only partially recrystallise during forging. This may be partially due to pinning of the grain boundaries by Laves phase precipitates. Cracks may form at those grain boundaries which are decorated with these brittle precipitates.

Keywords

forgingFeAl
Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 1128: Symposium U – Advanced Intermetallic-Based Alloys for Extreme Environment and Energy Applications , 2008 , 1128-U02-02
Copyright
Copyright © Materials Research Society 2009

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. McKamey, C.G., in: Physical Metallurgy and Processing of Intermetallic Compounds, eds. Stoloff, N.S. and Sikka, V.K., Chapman & Hall, New York, 1996, pp. 351–391.Google Scholar
2. Palm, M., Krein, R., Milenkovic, S., Sauthoff, G., Risanti, D., Stallybrass, C. and Schneider, A., Mater. Res. Soc. Symp. Proc., 980, II01–01 (2007).Google Scholar
3. Rodriguez, J., Moussa, S.O., Wall, J. and Morsi, K., Scr. Mater., 48, 707 (2003).Google Scholar
4. Huang, Y.D., Yang, W.Y. and Sun, Z.Q., Mater. Sci. Eng., A263, 75 (1999).Google Scholar
5. Zhang, Z.R. and Liu, W.L., Mater. Sci. Eng., A423, 343 (2006).Google Scholar
6. Zhao, P., Morris, D.G. and Morris-Munoz, M.A., J. Mater. Res., 14, 715 (1999).Google Scholar
7. Yu, X.Q. and Sun, Y.S., Mater. Sci. Technol., 20, 339 (2004).Google Scholar
8. Lyszkowski, R. and Bystrzycki, J., Intermetallics, 14, 1231 (2006).Google Scholar
9. Sikka, V.K., McKamey, C.G., Howell, C.R. and Baldwin, R.H., Fabrication and mechanical properties of Fe3Al-based iron aluminides, ORNL/TM-11456. Oak Ridge National Laboratory, 1990, pp. 1–76.Google Scholar
10. Liu, C.T., Sikka, V.K. and McKamey, C.G., Alloy development of FeAl aluminide alloys for structural use in corrosive environments, ORNL/TM-12199. Oak Ridge National Laboratory, 1993, pp. 1–61.Google Scholar
11. Krein, R. and Palm, M., Acta mater., 56, 2400 (2008).Google Scholar
12. Risanti, D.D. and Sauthoff, G., Intermetallics, 13, 1313 (2005).Google Scholar
13. Risanti, D.D. and Sauthoff, G., Mater. Sci. Forum, 475–479, 865 (2005).Google Scholar