Hostname: page-component-586b7cd67f-t7czq Total loading time: 0 Render date: 2024-11-28T14:48:39.475Z Has data issue: false hasContentIssue false
  • English
  • Français

FEM Analysis of Thermal Stresses in Advanced Electronic Packages

Published online by Cambridge University Press:  10 February 2011

Sven Rzepka ,
Matt A. Korhonen ,
Che-Yu Li  and
Ekkehard Meusel
Sven Rzepka
Affiliation:
Dept. of Electrical Engineering, Dresden University of Technology, D-01062 Dresden, Germany
Matt A. Korhonen
Affiliation:
Dept. of Materials Science and Engineering, Cornell University, Ithaca, NY 15853-1501, USA
Che-Yu Li
Affiliation:
Dept. of Materials Science and Engineering, Cornell University, Ithaca, NY 15853-1501, USA
Ekkehard Meusel
Affiliation:
Dept. of Electrical Engineering, Dresden University of Technology, D-01062 Dresden, Germany
Get access

Abstract

Following the general tendency of downsizing in microelectronic packages, the interposing layer between silicon chip and organic board is constantly reduced while the differences in thermal expansion stay constant. Consequently, thermal stresses have become the most important reliability concern in advanced packages. Finite element analysis is known as an effective way of theoretically studying the mechanical situation in multi-component systems with complex material behavior. The paper presents results of finite element simulations that provide practical guidance for design, process and material developments of chip size packaging (CSP), flip chip (FC), and direct chip attach (DCA) modules. Using realistic and efficient models, a low-cost CSP concept is assessed, the effects of underfill, underfill imperfections, and underfill defects on the reliability of FC modules are studied, and an optimum set of mechanical properties for underfill materials is proposed. Finally, reliability risk factors in DCA modules are identified and preliminary design guidelines are given.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 516: Symposium E – Low Dielectric Constant Materials IV , January 1998 , 345
Copyright
Copyright © Materials Research Society 1998

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

[1] Matthew, L.C., Distefano, T.H., Future Directions in TAB: the TCC/MCM Interconnect, 1994 ITAP & Flip Chip Proceedings, pp. 228–31Google Scholar
[2] Beyer, V., Kiichenmeister, F., Béttcher, M., Meusel, E., Flexible Polyimide Interposer for CSP Preparation, Adhesives in Electronics '98, 3rd Intl. Conference, Sept 28-30, 98, Binghampton, NY, USA, proceedings to be publishedGoogle Scholar
[3] Beyer, private communication, 1998 Google Scholar
[4] Nagesh, V.K.: Reliability of Flip Chip Solder Bump Joints, 1992 IEEE IRPS Proceedings, pp. 6–15 Google Scholar
[5] Soga, T., Nakano, F., Fuyama, M., Development of a High Reliability Flip-Chip Packaging Reinforced by Resin [Japanese], Trans. of the Institute of Electronics, Information and Communication Engineers C., vol. J70C (1987), no. 12, pp. 1575–82.Google Scholar
[6] Fillion, R.A., Wojnarowski, R.I., Gorcyzca, T.B., Wildi, E.J., Cole, H.S., Development of a Plastic Encapsulated Multichip Technology for High Volume, LowCost Commercial Electronics, IEEE Trans CPMT (B), vol. 18 (1995), no. I, pp. 59–65 Google Scholar
[7] Tummalla, R.R., Rymanszewki, E.J., Klopfstein, A.G., Microelectronics Packaging Handbook, Part I: Technology Drivers, 2nd edition, Chapman & Hall, 1997, pp. I–63.Google Scholar
[8] Pan, T.Y, Thermal Cyclic Induced Plastic Deformation in Solder joints – Part II: Accumulated Deformation in Through Hole Joints; IEEE Trans CHMT, vol. 14 (1991), no. 2, pp. 824–32Google Scholar
[9] Kapton, H. Polyimide Film, Technical Inrfrrmation Bulletin H, DuPont manufacturer data, 1993 Google Scholar
[10] Darveaux, R., Banerji, K., Constitutive Relations for Tin-Based Solder Joints, IEEE Trans CHMT, vol. 15 (1992) no. 6, pp. 1013–24Google Scholar
[ll] Rzepka, S., Waidhas, B., C4 Flip Chip Modules with Flexible Substrates: FEM Simulations and Experimental Investigations; 1994 ITAP & Flip Chip Proceedings, pp. 142–49Google Scholar
[12] Hu, J.M., Interfacial Stress Singularity Analysis – A Case Study for Plastic Encapsulated IC Packages; ASME, EEP-vol. Il/MD-vol. 64 (1995), pp. 13–23 Google Scholar
[13] Schwarzl, F.R., Polymermechanik – Struktur und mechanisches Verhalten von Polymeren, Springer Verlag Berlin Heidelberg New York, 1990, p. 123 Google Scholar
[14] Quian, Z., Lu, M., Wang, J, Liu, S., Testing and Constitutive Modeling of Polymer Films and Underfills by 6-axis Submicron Tester; Application qf Experimental Mechanics to Electronic Packaging ASME 1997, AMD-Vol. 226/EEP-Vol. 22, pp. 105–12Google Scholar
[15] Feustel, F., Lauterwald, B., Grätz, P., Meusel, E., A Cost-effective Assembly Process for Flip Chips on FR-4, 1998 IEEE ECTC Proceedings, not published yetGoogle Scholar
[16] Cotts, E., Lehmann, G., Singler, T., Underfill Process Development: Annual Report; Binghampton University, Depts. of Physic and Mechanical Engineering, 1997, p. 41 Google Scholar
[17] Rzepka, S., Feustel, F., Meusel, E., Korhonen, M.A., Li, C.Y., The Effect of Underfill imperfections on the Reliability of Flip Chip Modules: FEM Simulations and Experiments, 1998 ECTC Proceedings, pp. 362–70Google Scholar
[18] Han, S., Wang, K.K., Study on the Pressurized Underfill Encapsulation of Flip Chips, IEEE Trans CPMT (B), vol. 20 (1997), no. 4, pp. 434–42Google Scholar
[19] Polak, J., Helesic, J., Obrtlik, K., Fatigue Hardening and Cyclic Slip Location in Polycrystalline Copper, Metallic Materials, vol. 29 (1991), no. 2, pp. 68–75 Google Scholar