Hostname: page-component-586b7cd67f-tf8b9 Total loading time: 0 Render date: 2024-11-28T06:25:21.186Z Has data issue: false hasContentIssue false
  • English
  • Français

Enhanced Efficiency and Stability in P3HT:PCBM Bulk Heterojunction Solar Cell by using TiO2 Hole Blocking Layer

Published online by Cambridge University Press:  26 February 2011

Osamu Yoshikawa ,
Akinobu Hayakawa ,
Takuya Fujieda ,
Kaku Uehara  and
Susumu Yoshikawa
Osamu Yoshikawa
Affiliation:
[email protected], Institute of Advanced Energy, Kyoto University, Uji, Kyoto, N/A, Japan
Akinobu Hayakawa
Affiliation:
[email protected], Institute of Advanced Energy, Kyoto University, Uji, Kyoto, 611-0011, Japan
Takuya Fujieda
Affiliation:
[email protected], Institute of Advanced Energy, Kyoto University, Uji, Kyoto, 611-0011, Japan
Kaku Uehara
Affiliation:
[email protected], Institute of Advanced Energy, Kyoto University, Uji, Kyoto, 611-0011, Japan
Susumu Yoshikawa
Affiliation:
[email protected], Institute of Advanced Energy, Kyoto University, Uji, Kyoto, 611-0011, Japan
Get access

Abstract

Insertion of TiO2 layer between Al negative electrode and active layer of bulk-heterojunction gave a high solar conversion efficiency and high stability. The TiO2 layer was prepared by spin-coating titanium(IV)isopropoxide (Ti(OC3H7)4) on active layer of blended P3HT:PCBM. The parallel resistance (Rp) is increased by inserting TiO2 layer leading to an increase in Voc. The TiO2 layer works as a hole blocking layer and prevents the physical and chemical damages by the direct contact between P3HT:PCBM active layer and Al electrode resulting in improvement of the parallel resistance and rectification. The efficiency of P3HT:PCBM bulk heterojunction cell with TiO2 hole blocking layer attained 4.05% with a Isc 9.72 mA/cm2, Voc 0.60 V, and FF 0.70 by using optimized TiO2 film thickness and ratio of P3HT:PCBM condition.

Keywords

thin filmceramicTi
Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 965: Symposium S – Organic Electronics – Materials, Devices and Applications , 2006 , 0965-S11-04
Copyright
Copyright © Materials Research Society 2007

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

[1] Li, G., Shrotriya, V., Huang, J., Yao, Y., Mariarty, T., Emery, K. and Yang, Y. (2005), Nature Materials, 4, (11), pp. 864–868.Google Scholar
[2] M., Reyes-Reyes, Kim, K. and Carroll, D.L. (2005), J. Appl. Phys. Lett., 87, (8), pp. 1–3.Google Scholar
[3] Ma, W., Yang, C., Gong, X., Lee, K. and Heeger, A.J. (2005), Adv. Funct. Mater., 15, (10), pp. 1617–1622.Google Scholar
[4] Padinger, F., Rittberger, R.S., Sariciftci, N.S. (2003), Adv. Funct. Mater., 13, (1), pp. 85–88 Google Scholar
[5] Kim, Y., Choulis, S.A., Nelson, J., D.D.C., Bradley, Cook, S. and Durrant, J.R. (2005), J. Mater. Science, 40, (6), pp. 1371–1376.Google Scholar
[6] Brabec, C.J., Dyakonov, V., Parisi, J. and Sariciftci, N.S. (2003) Organic photovoltaics concepts and realization, Springer, New York.Google Scholar
[7] Krebs, F.C. and Spanggaard, H. (2005), Chem. Mater., 17, (21), pp. 5235–5237.Google Scholar