Hostname: page-component-586b7cd67f-r5fsc Total loading time: 0 Render date: 2024-11-28T10:59:04.888Z Has data issue: false hasContentIssue false
  • English
  • Français

Correlation between Adhesion Strength and Thin film/Substrate Mechanical Properties using the Nano-Scratch Technique

Published online by Cambridge University Press:  24 March 2011

Bo Zhou ,
Nicholas Randall  and
Barton Prorok
Bo Zhou
Affiliation:
CSM Instruments Inc., Needham 02494, MA, U.S.A
Nicholas Randall
Affiliation:
CSM Instruments Inc., Needham 02494, MA, U.S.A
Barton Prorok
Affiliation:
Materials Engineering, Auburn University, Auburn 36849, AL, U.S.A
Get access

Abstract

Scratch testing, as a mature technique for coating adhesion quantification, has been widely adopted by both industrial and academic fields in recent years. Following the urgent needs of very small materials characterization, nano-scratch testing has gradually replaced the traditional pull-off test for the study of ultra-thin film properties. In this research, the relationship between the adhesion strength and film/substrate mechanical properties was investigated to provide fundamental but crucial knowledge of the scratch mechanism. Scratch tests were performed on different film/substrate combinations using a Nano Scratch Tester with a sphero-conical diamond indenter. A progressive load mode was employed to cause coating failure during scratch on the film surface. The critical values of different failure mechanisms, such as cracking and delamination were accurately determined according to the scratch panorama image, penetration and residual depth data. In addition, the hardness (H) and modulus (E) values of the thin films and substrates were measured with an Ultra Nanoindentation Tester. The scratch critical failure loads were then plotted versus film/substrate H and E ratios. A unique relationship was found between these parameters that could help understand the true mechanism behind scratch adhesion and leverage this methodology to a new theoretical level.

Keywords

adhesionthin filmstrength
Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 1297: Symposium P – Deformation Mechanisms, Microstructure Evolution and Mechanical Properties of Nanoscale Materials , 2011 , mrsf10-1297-p03-07
Copyright
Copyright © Materials Research Society 2011

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Consiglio, R., Randall, N., Bellaton, B., and Von Stebut, J., Thin Solid Films. 332(1-2), 151–156 (1998)Google Scholar
2. Gonczy, S. and Randall, N., International Journal of Applied Ceramic Technology. 2(5), 422–428 (2005)Google Scholar
3. Okner, R., Shaulov, Y., Tal, N., Favaro, G., Domb, A., and Mandler, D., ACS Applied Materials & Interfaces. 1(4), 758–767 (2009)Google Scholar
4. Pelletier, H., Mendibide, C., and Riche, A., Progress in Organic Coatings. 62(2), 162–178 (2008)Google Scholar
5. Seubert, C. and Nichols, M., Journal of Coatings Technology and Research. 4(1), 21–30 (2007)Google Scholar
6. Zhou, B., Wang, L., Mehta, N., Morshed, S., Erdemir, A., Eryilmaz, O., and Prorok, B., Journal of Micromechanics and Microengineering. 16 1374 (2006)Google Scholar
7. Zhou, B. and Prorok, B., Materials Research Society Symposium Proceeding. 1086 (2008)Google Scholar
8. Zhou, B. and Prorok, B., Journal of Materials Research. 25 1671–1678 (2010)Google Scholar
9. Zhou, B. and Prorok, B., Experimental Mechanics. 50 793–801 (2010)Google Scholar