Hostname: page-component-586b7cd67f-g8jcs Total loading time: 0 Render date: 2024-11-28T16:46:31.719Z Has data issue: false hasContentIssue false
  • English
  • Français

Temperature sensing based on optical transmission in a LiBr heat pump

Published online by Cambridge University Press:  01 February 2011

Miguel Basurto-Pensado ,
Rosenberg J. Romero ,
Jesús Escobedo-Alatorre ,
Margarita Tecpoyotl-Torres ,
Aurelio H. Jiménez-Heredia  and
Javier Sanchez-Mondragon
Miguel Basurto-Pensado
Affiliation:
[email protected], Universidad Autónoma del Estado de Morelos, Av. Universidad # 1001 col. Chamilpa, Cuernavaca, Morelos, Mécxico, Mexico, 777 3297084, 7773297984
Rosenberg J. Romero
Affiliation:
[email protected], Universidad Autónoma del Estado de Morelos, Centro de Investigación en Ingeniería y Ciencias Aplicadas,, Mexico
Jesús Escobedo-Alatorre
Affiliation:
[email protected], Universidad Autónoma del Estado de Morelos, Centro de Investigación en Ingeniería y Ciencias Aplicadas, Mexico
Margarita Tecpoyotl-Torres
Affiliation:
[email protected], Universidad Autónoma del Estado de Morelos, Centro de Investigación en Ingeniería y Ciencias Aplicadas,, Mexico
Aurelio H. Jiménez-Heredia
Affiliation:
[email protected], Universidad Popular Autónoma del Estado de Puebla, Depto. de Física,, Mexico
Javier Sanchez-Mondragon
Affiliation:
[email protected], Universidad Autónoma del Estado de Morelos, Centro de Investigación en Ingeniería y Ciencias Aplicadas, Mexico
Get access

Abstract

A new technique, based on Optical Methods, has been tested for the evaluation of the lithium bromide (LiBr) concentration, a corrosive substance frequently used in heat pumps. Those solutions have large oxidizing capabilities. This technique avoids the direct contact between the electrodes and the LiBr aqueous solution within a thermodynamic absorption cycle. The viability of this technique in a potential commercial device, resides on its capability to detect working fluid concentrations within a temperature range from 25 °C up to 70 °C, those limiting temperature values correspond to the operating wavelengths of 1.33 μm and 1.55 μm, respectively. Our system determines the correlation among the signal and temperature data, for various concentrations, between 49 and 58 mass percentages. This function of two variables is represented as a surface with the transmittance, concentration and temperature as parameters and wavelength as reference. We discuss the adequate parameters characterization used in this technique.

Keywords

optical propertiessensorchemical composition
Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 888: Symposium V – Materials and Devices for Smart Systems II , 2005 , 0888-V03-17
Copyright
Copyright © Materials Research Society 2006

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

[1] Romero, R. J., Rivera, W. and Best, R., Solar Energy Materials and Solar Cells, Vol. 63 (4), (2000) 387 - 399.Google Scholar
[2] Herold, Keith E., Howe, Lawrence A. and Radermacher, Reinhard, International Journal of Refrigeration, Volume 14, Issue 5, September (1991) 264 - 272.Google Scholar
[3] Udd, E., Fiber optic sensor: An introduction for engineering and scientists, Ed. Wiley, New York, (1991)Google Scholar
[4] Chen, Kun-Huang, Hsu, Cheng-Chih, Su, Der-Chin, Applied Optics, Vol. 42 Issue 28 Page 5774 (October 2003)Google Scholar
[5] Christensen, D.A. and Ives, J.T., Proc. NATO Advanced studies institute, Dordrecht, Netherlands, (1987)Google Scholar