Hostname: page-component-586b7cd67f-gb8f7 Total loading time: 0 Render date: 2024-11-28T07:45:23.168Z Has data issue: false hasContentIssue false
  • English
  • Français

Suppression of Stiction in MEMS

Published online by Cambridge University Press:  10 February 2011

C. H. Mastrangelo
C. H. Mastrangelo*
Affiliation:
Center for Integrated Microsystems Department of Electrical Engineering and Computer Science University of Michigan, Ann Arbor, MI 48109-2122, USA
Get access

Abstract

Stiction failures in microelectromechanical systems (MEMS) occur when suspended elastic members are unexpectedly pinned to their substrates. This type of device failure develops both in fabrication and during device operation, being a dominant source of yield loss in MEMS. Stiction failures require first a collapse force that brings the elastic member contact with the substrate followed by an intersolid adhesion sufficiently large to overcome the elastic restoring force. Stiction failure mechanisms have been studied extensively elsewhere [1]. This paper briefly summarizes these mechanisms in a the practical way. Over the last decade, stiction failure rates in MEMS have been minimized using a wide variety of processing, surface treatment, and physical schemes. An update of these methods is provided.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 605: Symposium MM – Materials Science of Microelectromechanical Systems Devices II , 1999 , 105
Copyright
Copyright © Materials Research Society 2000

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

[1] Mastrangelo, C. H., “Adhesion related failure mechanisms in microelectromechanical systems,” Trib. Lett., vol. 3, pp. 223–238, 1997.10.1023/A:1019133222401Google Scholar
[2] Chau, K., Fung, C., Harris, P. R., and Dahrooge, G., “A verstile polysilicon diaphragm pressure sensor chip,” in Int. Electron Devices Meeting, (IEDM 91), pp. 695–697, 1991.Google Scholar
[3] Buurs, D. W., Micromechanics of Integrated Sensors and the Planar Processed Pressure Transducer. PhD thesis, University of Winsconsin, Madison, 1988.Google Scholar
[4] Lysko, J. M., Stolarski, E., and Jachowicz, R. S., “Capacitive silicon pressure sensor based on the one-side wafer processing,” in Transducers' 91, pp. 685–688, 1991.Google Scholar
[5] Kung, J. T. and Lee, H.-S., “An integrated air-gap capacitor process for sensor applications,” in Transducers'91, pp. 312–314, 1991.Google Scholar
[6] Yun, W., Howe, R. T., and Gray, P. R., “Surface micromachined, digitally force-balanced accelerometer with integrated CMOS detection circuitry,” in International Workshop on Solid-State Sensors and Actuators (Hilton Head' 92), pp. 126–131, 1992.Google Scholar
[7] Ristic, L., Gutteridge, R., Dunn, B., Mietus, D., and Bennett, P., “Surface micromachined polysilicon accelerometer,” in International Workshop on Solid-State Sensors and Actuators (Hilton Head' 92), pp. 118–121, 1992.Google Scholar
[8] Nathanson, H. C. and Guldberg, J., “Topologically structured thin films in semiconductor device operation,” Physics of Thin Films, vol. 8, pp. 251–298, 1975.Google Scholar
[9] Guckel, H. and Burns, D. W., “Fabrication of micromechanical devices from polysilicon films with smooth surfaces,” Sensors and Actuators, vol. 20, pp. 117–122, 1989.10.1016/0250-6874(89)87109-4Google Scholar
[10] Israelachvili, J. N., Intermolecular and Surface Forces. New York: Academic Press, 1985.Google Scholar
[11] Boer, M. P. de, Clews, P. J., Smith, B. K., and Michalske, T. A., “Adhesion of polysilicon microbeams in controlled humidity ambients,” in Mat. Res. Soc. Symp. Proc., vol. 518, pp. 131–136, 1995.Google Scholar
[12] Mastrangelo, C. H. and Hsu, C. H., “Mechanical stability and adhesion of microstructures under capillary forces- parts I and II,” Journal of Microelectromechanical Systems, vol. 2, pp. 33–55, 1993.Google Scholar
[13] Mastrangelo, C. H. and Hsu, C. H., “A simple experimental technique for the measurement of the work of adhesion of microstructures,” in International Workshop on Solid-State Sensors and Actuators (Hilton Head' 92), pp. 208–212, 1992.Google Scholar
[14] Flosdorf, E. W., Freeze Drying: Drying by Sublimation. Ann Arbor, MI: University Microfilms International, 1982.Google Scholar
[15] Holler, R. O., Freeze-Drying Biological Specimens. Washington, DC: Smithsonian Institution Press, 1979.Google Scholar
[16] Mellor, J. D., Fundamentals of Freeze Drying. New York: Academic Press, 1978.Google Scholar
[17] Takeshima, N., Gabriel, K. J., Ozaki, M., Takashashi, J., Horiguchi, H., and Fujita, H., “Electrostatic parallelogram actuators,” in Transducers' 91, pp. 63–66, 1991.Google Scholar
[18] Mulhern, G. T., Soane, D., and Howe, R. T, “Supercritical carbon dioxide drying for microstmctures,” in Transducers' 93, pp. 296–299, 1993.Google Scholar
[19] Dawes, C. J., Introduction to Biological Electron Microscopy: Theory and Techniques. Burlington, VT: Ladd Research Industries, 1988.Google Scholar
[20] Watanabe, H., Ohnishi, S., Honma, I., Kitajima, H., Ono, H., WIlhelm, R., and Sophie, A., “Selective etching of phosphosilicate glass with low pressure vapor hf,” J. Electrochem. Soc., vol. 142, pp. 237–243, 1995.10.1149/1.2043880Google Scholar
[21] Wong, M., Moslehi, M., and Bowling, R., “Wafer temperature dependence of the vapor-phase hf oxide etch,” J. Electrochem. Soc., vol. 140, pp. 205–208, 1993.Google Scholar
[22] Ruzillo, J., Torek, K., Daffron, C., Grant, R., and Novak, R., “Etching of thermal oxides in low pressure anhydrous HF/CHaOH gas mixture at elevated temperature,” J. Electrochem. Soc., vol. 140, pp. p. L64–L66, 1993.Google Scholar
[23] Hirano, T., Furuhata, T., and Fujita, H., “Dry releasing of electroplated rotational and overhanging structures,” in International Conference on Micro Electromechanical Systems (MEMS 93), Fort Lauderdale, FL, U.S.A. Feb. 1993, pp. 278–283.Google Scholar
[24] Mastrangelo, C. and Saloka, G., “A dry-release method based on polymer columns for microstructure fabrication,” Proc. IEEE Micro Electro Mech. Syst. Workshop, Fort Lauderdale, FL, U.S.A. Feb. 1993, pp. 77–81.Google Scholar
[25] Orpana, M. and Korhonen, A. O., “Control of residual stress of polysilicon thin films by heavy doping in surface micromachining,” in Transducers' 91, pp. 957–960, 1991.Google Scholar
[26] Kozlowski, F, Lindmair, N., Scheiter, T., Hierold, C., and Lang, W., “A novel method to avoid sticking of surface micromachined structures,” Transducers'95, pp. 220–223, 1995.Google Scholar
[27] Jansen, H. V., Gardeniers, J. G. E., Elders, J., Tilmans, H. A. C., and Elwenspoek, M., “Applications of fluorocarbon polymers in micromechanics and micromachining,” Sensors and Actuators, vol. A41–42, pp. 136–140, 1994.10.1016/0924-4247(94)80101-0Google Scholar
[28] Abe, T., Messner, W. C., and Reed, M., “Effective methods to prevent stiction during post-release-etch processing,” Proc. IEEE Micro Electro Mech. Syst. Workshop, Amsterdam, Neth, Feb. 1995, pp. 94–99.Google Scholar
[29] Gould, G. and Irene, E. A., “An in-situ study of aqueous HF treatment of silicon by contact angle measurement and ellipsometry,” J. Electrochem. Soc., vol. 135, pp. 1535–1539, 1988.Google Scholar
[30] Williams, R. and Goodman, A. M., “Wetting of thin layers of SiO2 by water,” Applied Physics Letters, vol. 25, pp. 531–532, 1974.Google Scholar
[31] Frieser, R. G., “Characterization of thermally grown SiO2 surfaces by contact angle measurements,” J. Electrochem. Soc., vol. 121, pp. 669–672, 1974.10.1149/1.2401884Google Scholar
[32] Hermansson, K., Lindberg, U., Hök, B., and Palmskog, G., “Wetting properties of silicon surfaces,” in Transducers'91, pp. 193–196, 1991.Google Scholar
[33] Graf, D., Grunder, M., Schulz, R., and Muhlhoff, L., “Oxidation of hf-treated si wafer surfaces in air,” J. Applied Phys., vol. 68, pp. 5155–5161, 1990.Google Scholar
[34] Watanabe, H., Hamano, M., and Harazono, M., “The role of atmospheric oxygen and water in the generation of water marks on the silicon surface in cleaning processes,” Mat. Sci. Eng., vol. B4, pp. 401–405, 1989.10.1016/0921-5107(89)90278-XGoogle Scholar
[35] Morita, M., Ohmi, T., Hagesawa, E., Kawakami, M., and Suma, K., “Control factor of native oxide growth on silicon in air or in ultrapure water,” Applied Physics Letters, vol. 55, pp. 562–564, 1989.Google Scholar
[36] Ulman, A., An Introduction to Ultrathin Organic Films: From Langmuir-Blodgett to Self-Assembly. Boston: Academic Press, 1991.Google Scholar
[37] Alley, R., Howe, R. T., and Komvopoulos, K., “The effect of release-etch processing on surface microstructure stiction,” in International Workshop on Solid-State Sensors and Actuators (Hilton Head' 92), pp. 202–207, 1992.Google Scholar
[38] Houston, M., Maboudian, R., and Howe, R. T., “Self-assembled monolayer films as durable anti-stiction coatings for polysilicon microstructures,” in International Workshop on Solid-State Sensors and Actuators (Hilton Head' 96), pp. 42–47, 1996.Google Scholar
[39] Srinivasan, U., Houston, M. R., Howe, R. T., and Maboudian, R., “Self-assembled fluorocarbon films for enhanced stiction reduction,” in Transducers' 97, pp. 1399–1402, 1997.Google Scholar
[40] Gogoi, B. P. and Mastrangelo, C. H., “Adhesion release and yield enhancement of microstructures using pulsed lorentz forces," Journal of Microelectromechanical Systems, vol. 4, pp. 185–192, 1995.10.1109/84.475545Google Scholar
[41] Kaajakari, V. and Lal, A., “Pulsed ultrasonic release and assembly of micromachines,” in Transducers' 99, pp. 212–215, 1999.Google Scholar
[42] Alley, R. L., Mai, P., Komvopulos, K., and Howe, R. T., “Surface roughness modification of interfacial contacts in polysilicon microstructures,” in Transducers' 93, pp. 288–291, 1993.Google Scholar
[43] Yee, Y., Chun, K., and Lee, J. D., “Polysilicon surface modification technique to reduce sticking of microstructures,” in Transducers' 95, pp. 206–209, 1995.Google Scholar
[44] Fan, L.-S., Integrated Micromachinery – Moving Structures in Silicon Chips. PhD thesis, University of California, Berkeley, 1990.Google Scholar
[45] Tang, W. C., Nguyen, T.-C. H., and Howe, R. T., “Laterally driven polysilicon resonant microstructures,” Proc. IEEE Micro Electro Mech. Syst. Workshop, Salt Lake City, Utah, U.S.A., Feb. 1989, pp. 53–59.Google Scholar
[46] Johnson, K. L., Kendall, K., and Roberts, A. D., “Surface energy and the contact of elastic solids,” Proc. Royal Soc. London A, vol. 324, pp. 301–313, 1971.Google Scholar
[47] Johnson, K. L., Contact Mechanics. New York: Cambridge University Press, 1987.Google Scholar
[48] Houston, M. R., Maboudian, R., and Howe, R. T., “Ammonium fluoride anti-stiction treatments for polysilicon microstructures,” Transducers'95, pp. 210–213, 1995.Google Scholar
[49] Hornbeck, L. J., “Digital light processing and MEMS: timely convergence for a bright future,” in Proc. SPIE Micromachining and Microfabrication Process Technology Conference, vol. SPIE 2639, pp. 1–21, 1995.Google Scholar
[50] Licari, J. J., Plastic Coatings for Electronics. New York: McGraw-Hill, 1970.Google Scholar
[51] Yasuda, H. and Hsu, T., “Some aspects of plasma polymerization of fluorine containing organic compounds,” J. Polym. Sci. Polym Chem. Ed., vol. 15, pp. 2411–2424, 1977.Google Scholar
[52] Yasuda, H. and Hsu, T., “Some aspects of plasma polymerization of fluorine containing organic compounds. ii. comparison of ethylene and tetrafluoroethylene,” J. Polymer Sci., vol. 16, pp. 415–425, 1978.Google Scholar
[53] Yasuda, H., Plasma Polymerization. New York: Academic Press, 1985.Google Scholar
[54] Buzzard, P. D., Plasma Polymerization of Tetrafluoroethylene in a Field Free Zone. PhD thesis, University of California, Berkeley, 1978.Google Scholar
[55] Man, P. F., Gogoi, B. P., and Mastrangelo, C. H., “Elimination of post-release adhesion in microstructures using thin conformal fluorocarbon films,” Proc. IEEE Micro Electro Mech. Syst. Workshop, San Diego, CA, U.S.A. Feb. 1996, pp. 55–60.Google Scholar
[56] Man, P. F., Gogoi, B. P., and Mastrangelo, C. H., “Elimination of post-release adhesion in microstructures using conformal fluorocarbon films,” Journal of Microelectromechanical Systems, vol. 6, pp. i25–34, March 1997.10.1109/84.557527Google Scholar