Hostname: page-component-78c5997874-dh8gc Total loading time: 0 Render date: 2024-11-02T18:36:00.165Z Has data issue: false hasContentIssue false
  • English
  • Français

Silicon Nitride Fibers Using Micro Fabrication Methods

Published online by Cambridge University Press:  22 February 2011

J. Koskinen  and
H. H. Johnson
J. Koskinen
Affiliation:
Department of Materials Science and Engineering, Cornell University, Ithaca, NY 14853.
H. H. Johnson
Affiliation:
Department of Materials Science and Engineering, Cornell University, Ithaca, NY 14853.
Get access

Abstract

Amorphous LPCVD and PECVD Si3N4 films have been patterned into fibers of various shapes using integrated circuit methods. A tensile test apparatus was developed which allows a simultaneous testing of up to 20 fibers. The average tensile strength of LPCVD Si3N4 fibers with a 30 μm gauge section was 7.0 ± 0.4 GPa. The corresponding value for PECVD Si3N4 was 2.4 ± 0.2 GPa. The following properties of the materials were measured: atomic composition (RBS, FRES), density, refractive index, internal stress, elastic modulus and micro hardness. A Weibull analysis of the tensile strength values was performed.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 130: Symposium C – Thin Films: Stresses and Mechanical Properties I , 1988 , 63
Copyright
Copyright © Materials Research Society 1989

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Steinwall, J.E., Johnson, H.H., Proceedings of Materials Research Society Conference, Reno, Nevada, April 5 - 9, 1988, in printGoogle Scholar
2. Hearn, E.W., Werner, D.J., Doney, D.A., J. Electrochem. Soc. 133, 1749 (1986)10.1149/1.2109008Google Scholar
3. Stone, D., LaFontaine, W.R., Alexopoulos, P., Wu, T.-W., Li, C.-Y., J. Mater. Res. 3,141 (1988)CrossRefGoogle Scholar
4. Doerner, M.F., Nix, W.D., J.Mater. Res. 1, 601 (1986)Google Scholar
5. Weibull, W., J. Appl. Mech. 18, 293 (1953)CrossRefGoogle Scholar
6. Olshansky, R., Maurer, R.D., J. Appl. Phys. 47, 4497 (1976)CrossRefGoogle Scholar
7. eg. Moreton, R., in Strong Fibers, ed. Watt, W. and Perov, B.V., (Elsevier, Amsterdam, 1985), p. 464 Google Scholar
8. Phani, K. K, J. Mater. Sci. 23, 2424 (1988)CrossRefGoogle Scholar
9. Goda, K., Fukuaga, H., J. Mater. Sci. 21, 4475 (1986)Google Scholar
10. H.M., Schwartz ed., Composite Materials Handbook, (McGraw-Hill, New York, 1984) p. 2.6–2.7 Google Scholar
11. Okamura, K., Sato, M., Hasegawa, Y., Ceram. Int. 13, 55 (1987)Google Scholar
12. R.F., Bunshah ed., Deposition Technologies for Thin Films and Coatings, (Noyes Publications, New Jersey, 1982)Google Scholar