Hostname: page-component-cd9895bd7-p9bg8 Total loading time: 0 Render date: 2024-12-28T01:36:38.743Z Has data issue: false hasContentIssue false
  • English
  • Français

Practical Work of Adhesion of Polymer Coatings Studied by Laser Induced Delamination

Published online by Cambridge University Press:  01 February 2011

A. Fedorov ,
J. Th. M. De Hosson ,
R. van Tijum  and
W.-P. Vellinga
A. Fedorov
Affiliation:
Department of Applied Physics, Materials Science Centre and the Netherlands Institute for Metals Research, University of Groningen, Nijenborgh 4, 9747 AG Groningen, The Netherlands
J. Th. M. De Hosson
Affiliation:
Department of Applied Physics, Materials Science Centre and the Netherlands Institute for Metals Research, University of Groningen, Nijenborgh 4, 9747 AG Groningen, The Netherlands
R. van Tijum
Affiliation:
Department of Applied Physics, Materials Science Centre and the Netherlands Institute for Metals Research, University of Groningen, Nijenborgh 4, 9747 AG Groningen, The Netherlands
W.-P. Vellinga
Affiliation:
Department of Applied Physics, Materials Science Centre and the Netherlands Institute for Metals Research, University of Groningen, Nijenborgh 4, 9747 AG Groningen, The Netherlands
Get access

Abstract

Laser Induced Delamination is a novel technique aimed at measuring the practical work of adhesion of thin polymer coatings on metal substrates. In this technique a laser pulse is used to create initial blisters which initiate further delamination of the film under the blister pressure. A simple elastic model is developed to describe the formation of the blisters. The model predicts the values for the blister height and pressure, which are in fair agreement with the experimental results. In order to account for possible plastic deformations, simulations using a finite element model with a mixed mode cohesive zone were carried out. The calculated stress fields are in agreement with those predicted by the elastic model suggesting that the contribution of plastic deformation to the measured work of fracture is rather limited.

Measurements are carried out on a number of samples, presenting ECCS steel substrate covered with 35 μm thick polyethylene terephthalate (PET) film. The tensile stresses created in the film at the interface required for delamination are estimated at 7-8 MPa, which corresponds to the practical work of adhesion G = (0.6± 0.1) J/m2.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 875: Symposium O – Thin Films - Stresses and Mechanical Properties XI , 2005 , O4.19
Copyright
Copyright © Materials Research Society 2005

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

[1] Volinsky, A.A., Moody, N.R., Gerberich, W.W., Acta Materialia 50, 441–466 (2002).Google Scholar
[2] Georgiou, I., Hadavinia, H., Ivankovic, A., Kinloch, A.J., Tropsa, V., Williams, J.G., The Journal of Adhesion 79, 239–265 (2003).Google Scholar
[3] Fedorov, A., Veen, A. van, Tijum, R. van, Hosson, J. Th. M. De, Mat. Res. Soc. Symp. Proc. 795, U8.61 (2004 Material Reasearch Society).Google Scholar
[4] Fedorov, A. and Hosson, J. Th. M. De, J. of Appl. Physics, (2005) (in press).Google Scholar
[5] Fentsel, E., Krauthammer, Th., Thin plates and Shells (Marcel Dekker 2001).Google Scholar
[6] Giessen, E. Vander, Eur. J. Mech., A/Solids 16, 87–106 (1997).Google Scholar
[7] Xu, X.-P., and Needleman, A., Model. Simul. Mater. Sci. Eng. 1, 111–132 (1993).Google Scholar