Hostname: page-component-586b7cd67f-dsjbd Total loading time: 0 Render date: 2024-11-24T13:29:59.387Z Has data issue: false hasContentIssue false
  • English
  • Français

Modeling of AlGaAs on Si tandem PV cells for extended spectral conversion

Published online by Cambridge University Press:  27 April 2011

Mahieddine Emziane  and
Alaeddine Mokri
Mahieddine Emziane
Affiliation:
Solar Energy Materials and Devices Lab. Masdar Institute of Science and Technology, Masdar City, PO Box 54224, Abu Dhabi, UAE. Email: [email protected]
Alaeddine Mokri
Affiliation:
Solar Energy Materials and Devices Lab. Masdar Institute of Science and Technology, Masdar City, PO Box 54224, Abu Dhabi, UAE. Email: [email protected]
Get access

Abstract

The primary objective of this modeling investigation is to optimize a two-junction three-terminal device under the AM1.5G spectrum. Based on previous studies, AlGaAs and Si cells, because of their energy bandgaps, can be combined together to achieve high-efficiency double-junction devices. In this study, the top cell is made of Al0.3Ga0.7As (1.817 eV) while the bottom cell is made of Si (1.124 eV). In order to avoid the losses and design constraints observed in two-terminal and four-terminal devices, the tandem cell AlGaAs/Si is designed with three-terminals. In order to determine the optimal structure of the device, the top and bottom junctions were investigated and optimized with regard to the thicknesses and doping level. The optimum configuration of the device shows an efficiency of 26.27% under the AM1.5G spectrum and one sun, which is higher than the efficiency of an optimized single-junction Si cell under the same illumination conditions. We also studied the effect of the optical concentration on the performance of the device and we found that the overall efficiency reaches over 31% under 50 suns.

Keywords

photovoltaicSidopant
Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 1288: Symposium G – Novel Fabrication Methods for Electronic Devices , 2011 , mrsf10-1288-g11-36
Copyright
Copyright © Materials Research Society 2011

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Duffie, J. A., Beckman, W. A., Solar Engineering of Thermal Processes, 3rd Edition, John Wiley & Sons, 2006, pp. 3.Google Scholar
2. Olson, J. M., Friedman, D. J. and Kutrz, S., in Handbook of Photovoltaic Science and Engineering, edited by Luque, A. and Hegedus, S., John Wiley & Sons, 2002, pp. 359.Google Scholar
3. Green, M. A., Emery, K., Hishikawa, Y. and Warta, W., Prog. Photovolt: Res. Appl. 18 (2010) 346.Google Scholar
4. Bertness, K. A., Kurtz, Sarah R., Friedman, D. J., Kibbler, A. E., Kramer, C. and Olson, J. M., Appl. Phys. Lett. 65 (1994) 989.Google Scholar
5. Hsu, L., Walukiewicz, W., Journal of Applied Physics 104 (2008) 024507.Google Scholar
6. Steinery, M. A., Wanlass, M. W., Carapella, J. J., Duda, A., Ward, J. S., Moriarty, T. E. and Emery, K. A., Prog. Photovolt: Res. Appl., 17 (2009) 587.Google Scholar
7. Emziane, M., Mater. Res. Soc. Symp. Proc. Vol. 1165 (2009) M08-13Google Scholar
8. PC1D, Version 5.9, © School of Photovoltaic and Renewable Energy Engineering at the University of New South Wales, Australia. Google Scholar