Hostname: page-component-78c5997874-dh8gc Total loading time: 0 Render date: 2024-11-03T05:48:39.135Z Has data issue: false hasContentIssue false
  • English
  • Français

“Incompressible” pore effect on the mechanical behavior of Low-K dielectric films

Published online by Cambridge University Press:  11 February 2011

Alex A. Volinsky ,
Manuel-Luis B. Palacio  and
William W. Gerberich
Alex A. Volinsky
Affiliation:
Motorola DigitalDNA™ Labs, Process and Materials Characterization Lab, Tempe, AZ 85283, USA
Manuel-Luis B. Palacio
Affiliation:
University of Minnesota, Dept. of Chem. Eng. and Materials Science, Minneapolis, MN 55455, USA.
William W. Gerberich
Affiliation:
University of Minnesota, Dept. of Chem. Eng. and Materials Science, Minneapolis, MN 55455, USA.
Get access

Abstract

New Low-K dielectric constant materials development is underway. Introducing porosity is one of the ways to lower the dielectric constant. Those are typically spin coated organic filled glasses. The pore size is on the order of a several nanometers and pore introduction compromises mechanical properties of low-K thin films, especially fracture toughness, as these materials are typically brittle.

In our previous studies we have evaluated different low-K dielectric constant materials in terms of their mechanical properties using nanoindentation. It was interesting to see that for a large range of various porous low-K materials the modulus-to-hardness ratio was constant. It was also found that the indenter contact is mostly elastic, as the loading and unloading portions of the load-displacement curve did not show any hysteresis, following indentation depth to the 3/2 power load dependence. Based on these results current analysis explains the observed constant modulus-to-hardness ratio.

The paper also describes the “incompressible” pore effect. As a particle gets smaller, the yield stress increases due to the Hall-Petch effect, but for the nanometer-size particles there are also high surface energy contributions that prevent is from deforming plastically. The same approach can be applied for a nanometer size pore elastic deformation, thus we call it an “incompressible” pore concept.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 750: Symposium Y – Surface Engineering 2002–Synthesis, Characterization and Applications , 2002 , Y9.9
Copyright
Copyright © Materials Research Society 2003

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

RERENCES

1. Adhihetty, I.S., Vella, J.B., Volinsky, A.A., Goldberg, C., Gerberich, W.W., 10th International Congress on Fracture, Honolulu, HI, (2001).Google Scholar
2. Vella, J.B., Adhihetty, I.S., Junker, K., and Volinsky, A.A., accepted for publication in International Journal of Fracture, (2002).Google Scholar
3. Volinsky, A.A., Vella, J.B., Gerberich, W.W., accepted for publication in Thin Solid Films, (2002).Google Scholar
4. Gibson, L.J. and Ashby, M.F., Cellular Solids: Structure and Properties. (Pergamon Press, 1988).Google Scholar
5. Oliver, W.C., Pharr, G.M., J. Mater. Res. 7, 1564, (1992).Google Scholar
6. Bahr, D.F., Hoehn, J.W., Moody, N.R., Gerberich, W.W., Acta mater. 45 (12), 5163–5175, (1997).Google Scholar
7. Sneddon, I.N., “Boussinesq's problem for a plat-ended cylinder”, Proc. Cambridge Phylos. Soc., 42, 29–39, (1946).Google Scholar
8. Volinsky, A.A., Gerberich, W.W., to be published in Journal of Microelectronics, (2003).Google Scholar
9. Lin, E.K., Wu, W.W., Jin, C., Wetzel, J.F., (Mater. Res. Soc. Proc. 612, Pittsburgh, PA, 2000) D4.1.1.Google Scholar
10. Wormington, M., Panaccione, C., Matney, K.M., Bowen, D.K., Phil. Trans. R. Soc. Lond. A. 357, 2827–2848, (1999).Google Scholar
11. Tymiak, N.I., Kramer, D.E., Bahr, D.F., Wyrobek, T.J., Gerberich, W.W., Acta Materialia, 49 (6), 1021–1034, (2001).Google Scholar
12. Giannakopoulos, A.E., Larsson, P -L., Vestergaard, R., International Journal of Solids & Structures, 31 (19), 2679–2708, (1994).Google Scholar
13. Johnson, K.L., Journal of Mechanics and Physics of Solids, 18, 115–126, (1970).Google Scholar