Hostname: page-component-586b7cd67f-vdxz6 Total loading time: 0 Render date: 2024-11-24T21:45:38.152Z Has data issue: false hasContentIssue false
  • English
  • Français

Electro-migration of Zinc during current-assisted pressure sintering of β-Zn4Sb3 – effect of process parameters and its influence on the thermoelectric properties

Published online by Cambridge University Press:  25 July 2011

T. Dasgupta ,
C. Stiewe ,
L. Boettcher ,
H. Yin ,
B.B. Iversen  and
E. Mueller
T. Dasgupta
Affiliation:
German Aerospace Center (DLR), Institute of Materials Research, D-51170, Cologne, Germany,
C. Stiewe
Affiliation:
German Aerospace Center (DLR), Institute of Materials Research, D-51170, Cologne, Germany,
L. Boettcher
Affiliation:
German Aerospace Center (DLR), Institute of Materials Research, D-51170, Cologne, Germany,
H. Yin
Affiliation:
University of Aarhus, Department of Chemistry and iNANO, Langelandsgade 140, DK-8000, Aarhus, Denmark
B.B. Iversen
Affiliation:
University of Aarhus, Department of Chemistry and iNANO, Langelandsgade 140, DK-8000, Aarhus, Denmark
E. Mueller
Affiliation:
German Aerospace Center (DLR), Institute of Materials Research, D-51170, Cologne, Germany,
Get access

Abstract

Compaction of β-Zn4Sb3 was carried out by current-assisted short term sintering under pressure (STS) using different material and process parameters. Surface Seebeck mapping (PSM) of the compacted specimens (along the uniaxial pressing direction) shows a wide gradation ranging from ∼40–180 μV/K due to electro-migration of Zinc along the current direction. The wide distribution of S corresponds to a mixture of Zn-Sb phases [1] which arise depending on the extent of Zinc migration during the STS process. Variation in the material and process parameters (average particle size, heating rate, compaction time/temperature) results in different spatial distribution of S. Measurements of electrical (σ), thermal (κ) conductivities and Seebeck (S) coefficients between room temperature and 523 K were carried out on two specimens having different average S values and distributions as observed by the PSM. The results indicate an increase in the lattice thermal conductivity (κL) and subsequent lower ZT in the specimens compared to the reported values for β-Zn4Sb3.

Keywords

thermoelectricthermal conductivityelectrical properties
Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 1325: Symposium E – Energy Harvesting—Recent Advances in Materials, Devices and Applications , 2011 , mrss11-1325-e06-06
Copyright
Copyright © Materials Research Society 2011

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Dasgupta, T., Stiewe, C., Boettcher, L., Hassdorf, R., Yin, H., Iversen, B. and Mueller, E., Journal of Materials Research-Focus Issue on Thermoelectrics (2011), article in press.Google Scholar
2. Caillat, T., Fleurial, J.P., and Borshchevsky, A., Journal of Physics and Chemistry of Solids, 58(7), 1119 (1997).Google Scholar
3. Pedersen, B.L. and Iversen, B.B., Applied Physics Letters, 92, 161907 (2008).Google Scholar
4. Stiewe, C., Dasgupta, T., Boettcher, L., Pedersen, B., Mueller, E., Iversen, B.B., Journal of Electronic Materials, 39(9), 1975 (2009).Google Scholar
5. Iversen, B.B., Journal of Materials Chemistry, 20, 10778 (2010).Google Scholar
6. Toberer, E.S., Raewel, P., Gariel, S., Tafto, J. and Snyder, G.J., Journal of Materials Chemistry, 20, 9877 (2010).Google Scholar
7. Ziolkowski, P., Karpinski, G., Platzek, D., Stiewe, C and Mueller, E., 25th Int. Conf. Thermoelectrics, p. 684 (2006).Google Scholar