Hostname: page-component-586b7cd67f-2brh9 Total loading time: 0 Render date: 2024-11-28T09:28:09.098Z Has data issue: false hasContentIssue false
  • English
  • Français

Direct production of the Ti-Zr-Ni-Cu icosahedral phase for hydrogen-storage applications by rapid quenching from the melt

Published online by Cambridge University Press:  01 February 2011

Andraz Kocjan ,
Paul J. McGuiness ,
Aleksander Recnik  and
Spomenka Kobe
Andraz Kocjan
Affiliation:
[email protected], Joseph Stefan Institute, Department for nanostructured materials, Jamova cesta 39, Ljubljana, 1000, Slovenia, + 386 01 477-3947, + 386 01 477-3221
Paul J. McGuiness
Affiliation:
[email protected], Joseph Stefan Institute, Dept. for nanostructured materials, Jamova cesta 39, Ljubljana, 1000, Slovenia
Aleksander Recnik
Affiliation:
[email protected], Joseph Stefan Institute, Dept. for nanostructured materials, Jamova cesta 39, Ljubljana, 1000, Slovenia
Spomenka Kobe
Affiliation:
[email protected], Joseph Stefan Institute, Dept. for nanostructured materials, Jamova cesta 39, Ljubljana, 1000, Slovenia
Get access

Abstract

Our study focused on the formation of Ti40Zr40Ni20 and Ti45Zr35Ni17Cu3 icosahedral (i-phase) quasicrystals directly from the melt and their subsequent characterization and high-pressure hydrogenation. The samples were produced in an inert-gas melt-spinning device from a series of arc-melted precursors. By varying the wheel speeds we were able to produce a range of crystallographic structures, from amorphous, through quasicrystalline, to crystalline. The ribbon thickness showed the expected reduction with wheel speed, from 120 microns to 30 microns, while the Ms exhibited a surprisingly modest change with wheel speed. The XRD analysis showed that depending on the cooling rate it was possible to freeze the icosahedral phase directly from the melt, without any subsequent heat-treatment. Using the same procedure to test the range of formation wheel speeds for a comparable system we also produced samples containing up to 3 atomic % copper. Using transmission electron microscopy we have confirmed that the ribbons contain nanosized particles of Ti40Zr40Ni20 icosahedral phase imbedded in an amorphous matrix with the same composition. The average particle size of the i-phase was approximately 20 nm. The 5-fold symmetry was confirmed by selected-area electron diffraction and high-resolution TEM having the crystallite oriented close to the symmetry axis. Both our X-ray diffraction measurements and the TEM observations have provided direct evidence for the quasicrystalline ordering of Ti40Zr40Ni20 by rapid quenching from the melt. To test the hydrogen-absorption properties of the icosahedral phase we crushed ribbons into finer particles to provide fresh, new surfaces to aid hydrogen dissociation at the metal surface. The uptake of hydrogen was found to be critically dependent on the surface state of the Ni–Ti–Zr ribbons; even modest exposure to the atmosphere produced a protective layer of oxide on the surface that practically prevented any hydrogen being taken up by the icosahedral phase. The concentration of hydrogen in the i-phase was determined from the shift in the XRD peaks. The calculated expansion of aq was 6% and the corresponding [H]/[M] value was 1.5.

Keywords

hydrogenationrapid solidificationamorphous
Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 1042: Symposium S – Materials and Technology for Hydrogen Storage , 2007 , 1042-S01-04
Copyright
Copyright © Materials Research Society 2008

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Viano, A.M., Majzoub, E.H., Stroud, R.M., Kramer, M.J., Misture, S.T., Gibbons, P.C., Kelton, K.F., Phil. Mag. A 78 (1998) 131–141 Google Scholar
2. Kelton, K. F. and Gibbons, P. C., MRS Bulletin 22(11) (1997) 69 Google Scholar
3. Hydrogenation of titanium-based quasicrystals, Viano, A. M., Stroud, R. M., Gibbons, P. C., McDowell, A. F., Conradi, M. S., and Kelton, K. F., Phys. Rev. B 51 (1995) 12026–12029 Google Scholar
4.Icosahedral and amorphous phases in melt-spun Ti-Zr-Ni-Cu alloys, Wang, L., Inoue, A., Materials Transactions 42 (12) (2001) 2637–2640 Google Scholar
5. Formation and mechanical properties of Ti-Zr-Ni-Cu amorphous alloy containing icosahedral nanoscale quasicrystalline phase, Wang, L., Ma, L., Innoue, A., Materials Transactions 43 (9) (2002) 2346–2349 Google Scholar
6.Formations of amorphous and quasicrystal phases in Ti-Zr-Ni-Cu alloys, Wang, L., Ma, L., Ma, C., Inoue, A., Journal of Alloys and Compounds 361 (1-2) (2006) 234–240 Google Scholar
7. Hydrogen absorption in Ti–Zr–Ni–Cu amorphous alloy, Guo, X.Q., Louzguine, D.V., Yamaura, S., Ma, L.Q., Sun, W., Hasegawa, M., Inoue, A., Mat. Sci. and Eng. A338 (2002) 97–100 10.1016/S0921-5093(02)00091-6Google Scholar
8. Indexing of icosahedral quasiperiodic crystals, Cahn, J.W., Shechman, D., Gratias, D., Journal of Materials Research (1986), Vol. 1, 13–26 10.1557/JMR.1986.0013Google Scholar