Hostname: page-component-586b7cd67f-vdxz6 Total loading time: 0 Render date: 2024-11-30T22:52:47.275Z Has data issue: false hasContentIssue false
  • English
  • Français

The Use of Exothermic Reactions in the Synthesis and Densification of Ceramic Materials

Published online by Cambridge University Press:  29 November 2013

J.B. Holt
Get access

Extract

This article will provide information about chemical processes which rely on the heat evolved during reaction to synthesize and, in some cases, to simultaneously density single-phase or composite ceramic materials. Although the basic concept underlying these processes is simple, the high temperature reactions are complex and require careful study with individual systems before their potential as fabrication processes can be fully realized.

Many reactions between solids involving elements and/or compounds, or between solids and gases are highly exothermic. Listed in Table I is a selected group of typical chemical reactions accompanied by their calculated adiabatic temperatures. As a general rule any reaction with an adiabatic temperature ~2000°C or over can be reacted under combustion conditions. For example, suppose that a cold-pressed cylindrical compact of titanium and boron powder (Eq. 1) is ignited at the top surface with a convenient source of heat such as a laser. From the igniting surface a combustion wave rapidly self-propagates down the compact, transforming the reactants into the TiB2 product. Figure 1 shows a Ti and C powder compact where the combustion wave has progressed about halfway down the compact.

Type
Ceramics
Information
MRS Bulletin , Volume 12 , Issue 7 , November 1987 , pp. 60 - 65
Copyright
Copyright © Materials Research Society 1987

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1.Frankhouser, W.L., System Planning Corporation Reports, Arlington, VA.Google Scholar
2.Miyamoto, Y., Koizumi, M., and Yamada, O., Commum. Am. Ceram. Soc. 67, (1984) p. C224.Google Scholar
3.Yamado, O., Miyamoto, Y., and Koizumi, M., Am. Ceram. Soc. Bull. 64, (1985) p. 319.Google Scholar
4.Odawara, O., Trans. Jpn. Inst. Metals 26, (1985) p. 336.CrossRefGoogle Scholar
5.McCauley, J.W., Corbin, N.D., Resetar, R., and Wong, P., Ceram. Eng. Sci. Proc. 3, (1982) p. 538.CrossRefGoogle Scholar
6.Logan, K., presented at the DARPA Symposium on Combustion Synthesis, Daytona Beach, FL, October 21, 1985 (unpublished).Google Scholar
7.Niiler, A., presented at the DARPA Symposium on Combustion Synthesis, Daytona Beach, FL, October 21, 1985 (unpublished).Google Scholar
8.Holt, J.B. and Munir, Z.A., J. Mater. Sci. 21, (1986) p. 251.CrossRefGoogle Scholar
9.Kaper, H.G., Leaf, G.K., Margolis, S.B., and Matkowsky, B.J., Sandia National Laboratory, Livermore, CA, SAND86-8666, February 1986.Google Scholar
10.Booty, M.R., Margolis, S.B., and Matkowsky, B.J., Sandia National Laboratory, Livermore, CA, SAND85-8841, October 1985.Google Scholar
11.Margolis, S.B., SIAM J. Appl. Math. (2) 43 (1983) p. 357.Google Scholar
12.Holt, J.B. and Kingman, D.D., presented at the 19th University Conference on Ceramic Science, North Carolina State University, Raleigh, NC, November 8, 1982 (unpublished).Google Scholar
13.Cutler, R.A., presented at the DARPA Symposium on Combustion Synthesis, Daytona Beach, FL, October 21, 1985 (unpublished).Google Scholar
14.Holt, J.B., presented at the Powder Science and Technology Meeting, Boston, MA, August 1986 (to be published in Adv. Ceram.).Google Scholar
15.Munir, Z.A. and Holt, J.B., J. Mater. Sci. 22, (1987) p. 710.CrossRefGoogle Scholar
16.Holt, J.B., Kingman, D.D., and Bianchini, G.M., presented at the DARPA Symposium on Combustion Synthesis, Dayton a Beach, FL, October 21, 1985 (unpublished).Google Scholar
17.Merzhanov, A. G., Vestnik Akademii Nauk SSSR 10, (1981) p. 30.Google Scholar
18.Rice, R.W., McDonough, W.J., Richardson, G.Y., Kunetz, J.M., and Schroeter, T., Ceram. Eng. and Sci. Proc. 7 (7-8), (1968) p. 651–760.Google Scholar
19.Horigachi, Y. and Nomara, Y., Bull. Chem. and Soc. Jpn. 36, (1963) p. 486.CrossRefGoogle Scholar
20.Suzuki, H., Yoshida, H., and Kimura, Y., J. Ceram. Assoc. Jpn. 77, (1969) p. 278.CrossRefGoogle Scholar
21.Adadurov, G.A., Breusov, O.N., Dremin, A.N., and Drobyshev, V.N., Zh. Noerg. Khim. 15, (1970) p. 2887.Google Scholar