Hostname: page-component-586b7cd67f-r5fsc Total loading time: 0 Render date: 2024-11-24T02:48:50.025Z Has data issue: false hasContentIssue false
  • English
  • Français

Microstructural Design and Control of Silicon Nitride Ceramics

Published online by Cambridge University Press:  29 November 2013

Mamoru Mitomo ,
Naoto Hirosaki  and
Hideki Hirotsuru
Get access

Extract

The improvement of mechanical properties by microstructural control has been one of the main topics of interest in the development of silicon nitride ceramics. Toughening, by developing an in situ composite or self-reinforced microstructure, has attracted particular attention.

Microstructural design is a key factor in the optimization of processing parameters. The microstructures of sintered materials are composed of silicon nitride grains and grain boundaries, which can be either crystalline, amorphous, or partially crystalline, depending on the composition, amount of sintering additives, and processing parameters. Silicon nitride ceramics have been fabricated with an addition of metal oxides and rare-earth oxides that form a liquid phase during sintering and accelerate grain boundary diffusion. The effect of composition of the glassy phase on the mechanical properties of ceramics is presented by Becher et al. and Hoffmann elsewhere in this issue. This article focuses specifically on the design and control of grain size.

As it is well recognized, many processing parameters affect grain growth behavior and the resulting microstructure. During sintering, the α- to β-phase transformation leads to a self-reinforcing microstructure on account of the anisotropic grain growth of the stable hexagonal β- Si3N4 phase. Therefore, α-rich powders are widely used for starting materials. Phase transformation accelerates anisotropic grain growth, resulting in an increase in the fracture toughness of Si3N4 ceramics. Kang and Han discuss the effect of phase transformation on nucleation and grain growth in an article in this issue. The effect of the grain-size distribution on microstructural development is described in this article, based on studies conducted mostly with β-Si3N4 powders.

Type
Silicon-Based Ceramics
Information
MRS Bulletin , Volume 20 , Issue 2 , February 1995 , pp. 38 - 41
Copyright
Copyright © Materials Research Society 1995

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1.Mitomo, M., in Advanced Ceramics-2, edited by Sōmiya, S. (Elsevier Applied Science, London, 1986) p. 147.Google Scholar
2.Mitomo, M. and Tajima, Y., J. Ceram. Soc. Jpn. 99 (1991) p. 1014 (in Japanese).CrossRefGoogle Scholar
3.Hoffmann, M.J. and Petzow, G., in Silicon Nitride Ceramics: Scientific and Technological Advances, edited by Chen, I-W., Becher, P.F., Mitomo, M., Petzow, G., and Yen, T-S. (Mater. Res. Soc. Symp. Proc. 287, Pittsburgh, PA, 1993) p. 3.CrossRefGoogle Scholar
4.Tani, E., Umebayashi, S., Kishi, K., Kobayashi, K., and Nishijima, M., Am. Ceram. Soc. Bull. 65 (1986) p. 1311.Google Scholar
5.Li, C.W. and Yamanis, J., Ceram. Eng. Sci. Proc. 10 (1989) p. 632.CrossRefGoogle Scholar
6.Wittmer, D.E., Doshi, D., and Paulson, T.E., Ceram. Eng. Sci. Proc. 10 (1989) 13 (1992) p. 907.Google Scholar
7.Mitomo, M., in Proc. 1st Int. Symp. Sci. Eng. Ceram., edited by Kimura, S. and Niihara, K. (Ceramic Society of Japan, Tokyo, 1991) p. 101.Google Scholar
8.LangeJ, F.F.. Am. Ceram. Soc. 62 (1979) p. 428.CrossRefGoogle Scholar
9.Wötting, G., Kanka, B., and Ziegler, G., in Non-Oxide Technical and Engineering Ceramics, edited by Hampshire, S. (Elsevier Applied Science, London, 1986) p. 83.CrossRefGoogle Scholar
10.Brook, R.J., Gilbart, E.G., Shaw, N.J., and Eisele, U., Powder Metall. 28 (1985) p. 105.CrossRefGoogle Scholar
11.Becher, P.F., J. Am. Ceram. Soc. 74 (1991) p. 255.CrossRefGoogle Scholar
12.Faber, K.T. and Evans, A.G., Acta Metall. 13 (1983) p. 577.CrossRefGoogle Scholar
13.Hirosaki, N., Akimune, Y., and Mitomo, M., J. Am. Ceram. Soc. 76 (1993) p. 1892; in Reference 3, p. 405.CrossRefGoogle Scholar
14.Li, C.W., Gasdaska, C.J., Goldacker, J., and Lui, S.C., in Reference 3, p. 473.Google Scholar
15.Mitomo, M., Tsutsumi, M., Tanaka, H., Uenosono, S., and Saito, F., J. Am. Ceram. Soc. 73 (1990) p. 2441.CrossRefGoogle Scholar
16.Mitomo, M. and Uenosono, S., J. Mater. Sci. 26 (1991) p. 3940.CrossRefGoogle Scholar
17.German, R.M., Liquid Phase Sintering (Plenum Publishing, New York, 1985).CrossRefGoogle Scholar
18.Mitomo, M., Hirotsuru, H., Uematsu, H., and Nishimura, T., J. Am. Ceram. Soc., submitted.Google Scholar
19.Wakai, F., Kodama, Y., Sakaguchi, S., Murayama, N., Izaki, K., and Niihara, K., Nature 344 (1990) p. 421.CrossRefGoogle Scholar
20.Chen, I-W. and Xue, L.A., J. Am. Ceram. Soc. 73 (1990) p. 2585.CrossRefGoogle Scholar
21.Hirao, K., Nagaoka, T., Brito, M.E., and Kanzaki, S., J. Am. Ceram. Soc. 77 (1994) p. 1857.CrossRefGoogle Scholar
22.Hirosaki, N., Akimune, Y., and Mitomo, M., J. Am. Ceram. Soc. 77 (1994) p. 1093.CrossRefGoogle Scholar
23.Shalek, P.D., Petrovic, J.J., Hurley, G.F., and Gac, F.D., Am. Ceram. Soc. Bull. 65 (1986) p. 351.Google Scholar
24.Homeny, J., Vaughn, W.L., and Ferber, M.K., Am. Ceram. Soc. Bull. 66 (1987) p. 333.Google Scholar
25.Evans, A.G., J. Am. Ceram. Soc. 65 (1982) p. 127.CrossRefGoogle Scholar