Hostname: page-component-cd9895bd7-mkpzs Total loading time: 0 Render date: 2024-12-27T09:32:13.532Z Has data issue: false hasContentIssue false
  • English
  • Français

Materials for Advanced Flywheel Energy-Storage Devices

Published online by Cambridge University Press:  29 November 2013

S.J. DeTeresa
Get access

Extract

Flywheels are mechanical devices that store kinetic energy in a rotating mass. A simple example is the potter's wheel. For energy storage and conversion, an efficient method to exchange energy with a flywheel device is by converting the energy between mechanical and electrical forms. Typically a flywheel designed to perform this type of energy exchange is a combination of a motor and a generator. Energy is transferred into the device for storage by using it as a motor to consume electrical energy and spin the mass. This energy can be recovered with an efficiency exceeding 80% by using the flywheel as an electrical generator. Although the concept of storing energy in a rotating mass is an ancient idea, the relatively recent advent of advanced fiber-composite materials offers the potential for improved energy storage and conversion using rotating electromechanical devices.

The achievable energy density (energy/weight) of a simple flywheel design, such as that shown schematically in Figure 1, is proportional to the specific strength (strength/density) of the material. The particular type of composite flywheel shown in this figure is composed entirely of circumferentially wrapped fiber. Although other designs have been suggested and constructed, this version is the most common for energy-storage applications. As discussed in the earliest papers on the subject, such as the article by Post and Post, the proportionality between energy density and specific strength favors the use of fiber composites. The remarkable combination of mechanical properties and low density achieved with fiber composites has made them attractive and nearly essential for aerospace applications.

Type
Advanced Materials for Energy Storage
Information
MRS Bulletin , Volume 24 , Issue 11 , November 1999 , pp. 51 - 56
Copyright
Copyright © Materials Research Society 1999

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1.Post, R.F. and Post, S.F., Sci. Am. 229 (6) (1973) p. 17.CrossRefGoogle Scholar
2.Dresselhaus, M.S., Dresselhaus, G., Sugihara, K., Spain, I.L., and Goldberg, H.A., Graphite Fibers and Filaments (Springer-Verlag, Berlin, 1988) p. 238.CrossRefGoogle Scholar
3.Lowrie, R.E., in Modern Composite Materials, edited by Broutman, L.J. and Krock, R.H. (Addison-Wesley, Reading, MA, 1967) p. 270.Google Scholar
4.Hartman, D.R., Greenwood, M.E., and Miller, D.M., “High-Strength Glass Fibers,” OCF Technical Paper, Pub. No. 1-PL-19025 (Owens-Corning Fiberglas, Toledo, OH, 1994).Google Scholar
5.Bogatyrjov, V.A., Bubnov, M.M., Dianov, E.M., Prokhorov, A.M., Rumyantsev, S.D., and Semjonov, S.L., Sov. Tech. Phys. Lett. (Engl. Transl.) 14 (1988) p. 343.Google Scholar
6.Torayca Technical Reference Manual (Toray Industries, Tokyo) p. 2–1–10.Google Scholar
7.Stone, R.G., Fiber-Composite Flywheel Program: Quarterly Progress Report, UCRL-50033-76-4 (Lawrence Livermore National Laboratory, Livermore, CA, October-December 1976) p. 4, 6.Google Scholar
8.Fiber, Hollex, Owens-Corning Technical Bulletin, Pub. No. 1-ASP-18355 (Owens-Corning Fiberglas, Toledo, OH, 1993).Google Scholar
9.Plastics for Aerospace Vehicles, Part I, Reinforced Plastics, MIL-HDBK-17A (U.S. Department of Defense, January 1971).Google Scholar
10. Kevlar 49 Data Manual (E.I. DuPont de Nemours & Co., Wilmington, DE, 1986) p. 29.Google Scholar
11.Nguyen, H.X. (private communication).Google Scholar
12.Reed, R.P and McCloskey, J.D., Composite Struts for SMES Plants, NISTIR 504 (U.S. Dept. of Commerce, Boulder, CO, October 1994) p. V-7, V–12.Google Scholar
13.Kasen, M.B., ASTM STP 580: Composite Reliability (American Society for Testing and Materials, Philadelphia, 1975) p. 586.CrossRefGoogle Scholar
14.Glaser, R.E., Moore, R.L., and Chiao, T.T., Compos. Tech. Rev. 5 (1) (1983) p. 21.Google Scholar
15.Christensen, R.M. and Glaser, R.E., J. Appl. Mech. 52 (1985) p. 1.CrossRefGoogle Scholar
16.Rinde, J.A., LLL Materials Program for Fiber-Composite Flyzvheels, UCRL-83043 (Lawrence Livermore Laboratory, Livermore, CA, July 1979).Google Scholar
17.Christensen, R.M. and Glaser, R.E., Mech. Res. Commun. 21 (2) (1994) p. 121.CrossRefGoogle Scholar
18.Thomas, D.A., J. Propulsion 8 (1) (1992) p. 87.CrossRefGoogle Scholar
19.Lifshitz, J.M. and Rotem, A., Fibre Sci. Tech. 3 (1970) p. 1.CrossRefGoogle Scholar
20.Chiao, T.T., Chiao, C.C., and Terry, R.J., “Lifetimes of Fiber Composites Under Sustained Loading,” UCRL-78367 (Lawrence Livermore Laboratory, Livermore, CA, November 17,1976).Google Scholar
21.Schmitz, G.K. and Metcalfe, A.G., Ind. Eng. Chem. Prod. Res. Dev. 5 (1) (1966) p. 1.Google Scholar
22.Chiao, T.T. and Moore, R.L., J. Comp. Mater. 6 (1972) p. 6.Google Scholar
23.Chiao, C.C., Sherry, R.J., and Chiao, T.T., Composites (1976) p. 107.Google Scholar
24.Zhurkov, S.N., Int. J. Fracture Mech. 1 (1965) p. 311.CrossRefGoogle Scholar
25.Phoenix, S.L., Schwartz, P., and Robinson, H.H. IV, Compos. Sci. Technol. 32 (1988) p. 81.CrossRefGoogle Scholar
26.Christensen, R.M. and Wu, E.M., Eng. Tract. Mech. 14 (1981) p. 215.CrossRefGoogle Scholar
27.Glaser, R.E., Christensen, R.M., and Chiao, T.T., Compos. Rev. 6 (1984) p. 164.Google Scholar
28.Christensen, R.M., J. Rheol. 25 (5) (1981) p. 529.CrossRefGoogle Scholar
29.Liu, C.Y. and Chamis, C.C., in Proc. 20th Annual Meeting of the Society of the Plastics Industry, Section 5-D (Society of the Plastics Industry, Washington, DC, 1965) p. 1.Google Scholar
30.Reuter, R.C. Jr., ASTM STP 521: Analysis and Test Methods for High Modulus Fibers and Composites (American Society for Testing and Materials, Philadelphia, 1973) p. 264.Google Scholar
31.Tarnopolskii, Y. M. and Roze, A.V., Features of the Calculation of Reinforced Plastic Parts, AD-772 721 (National Technical Information Service, Springfield, VA 1973) p. 165.Google Scholar
32.Lee, S.-Y., “Filament Winding Process Model,” PhD thesis, Stanford University, 1989.Google Scholar
33.Pardoen, G.C., Nudenberg, R.D., and Wartout, B.E., in Proc. 1980 Flywheel Technology Symp. (National Technical Information Service, Springfield, VA, 1980) p. 159.Google Scholar