Hostname: page-component-586b7cd67f-dsjbd Total loading time: 0 Render date: 2024-11-24T02:42:32.080Z Has data issue: false hasContentIssue false
  • English
  • Français

High-Temperature Properties of Si3N4 Ceramics

Published online by Cambridge University Press:  29 November 2013

M.J. Hoffmann
Get access

Extract

Silicon nitride is a highly covalent bonded compound which decomposes at 1877°C. Therefore, it is impossible to densify Si3N4 without sintering additives. Densification is achieved by liquid-phase sintering usually using metal oxides such as MgO, Y2O3, A12O3, and most of the rare-earth oxides as sintering additives. The oxides react with SiO2—always present at the surface of Si3N4 particles—to form an oxide melt and, with increasing temperature, an oxynitride melt by dissolution of Si3N4. The resulting microstructure consists of elongated Si3N4 needles embedded in a matrix of smaller equiaxed Si3N4 grains and a grain boundary phase, as shown in Figure 1. The amount and chemistry of the sintering aids determine the volume fraction of the grain boundary phase. The content required for complete densification depends on the sintering techniques: 2–5 vol% additives are sufficient if densification is supported by a high external pressure (hot pressing [HP] or hot isostatic pressing [HIP]); pressureless-sintered and gas-pressure-sintered (10-MPa nitrogen pressure) materials have additive contents of up to 15 vol%. Today, silicon nitride ceramics are regarded as a class of material comparable to steel. Different qualities depend on the size and shape of the silicon nitride grains and the amount and chemistry of the grain boundary phase. Materials with a high room-temperature strength exhibit a finegrained, elongated microstructure, while materials with a high fracture toughness are more coarse-grained. In both cases, a weak interface is required to induce transgranular fracture. (See Becher et al. in this issue.) Since all Si3N4 grains are completely wetted by the grain boundary phase, the interface strength is determined by the additive composition. Nevertheless, a contradiction arises between the development of high-strength and high-toughness Si3N4 ceramics and high-temperature resistant materials because the grain boundary phase is responsible for the excellent properties at low temperatures, but limits the properties at temperatures above its softening point.

Type
Silicon-Based Ceramics
Information
MRS Bulletin , Volume 20 , Issue 2 , February 1995 , pp. 28 - 32
Copyright
Copyright © Materials Research Society 1995

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1.Kawashima, T., Okamoto, H., Yamamoto, H., and Kitamura, A., J. Ceram. Soc. Jpn. 99 (1991) p. 1.CrossRefGoogle Scholar
2.Becher, P.F., Hwang, S-L., Lin, H.T., and Tiegs, T.N., in Tailoring of Mechanical Properties of Si3N4 Ceramics, edited by Hoffmann, M.J. and Petzow, G. (NATO ASI Series, Kluwer Academic Publishers, Dordrecht, 1994) p. 87.CrossRefGoogle Scholar
3.Gaukler, L.J. and Petzow, G., in Nitrogen Ceramics, edited by Riley, F.R. (NATO Advanced Study Institute, Canterbury, 1976).Google Scholar
4.Gaukler, L.J., Hohnke, H., and Tien, T-Y., J. Amer. Ceram. Soc. 63 (1980) p. 35.CrossRefGoogle Scholar
5.Hoffmann, M.J. and Petzow, G., in Silicon Nitride Ceramics: Scientific and Technological Advances, edited by Chen, I-W., Becher, P.F., Mitomo, M., Petzow, G., and Yen, T-S. (Mater. Res. Soc. Symp. Proc. 287, Pittsburgh, PA, 1993) p. 3.CrossRefGoogle Scholar
6.Patel, J.K. and Thompson, D.P., Brit. Ceram. Trans. J. 87 (1988) p. 70.Google Scholar
7.Mahoney, F.M., Hoffmann, M.J., Petzow, G., and Boberski, C., in Proc. 4th Int. Symp. Ceramics Mater, and Components for Engines, edited by Carlsson, R., Johansson, T., and Kahlman, L. (Elsevier Applied Science, London and New York, 1992) p. 649.CrossRefGoogle Scholar
8.Lewis, M.H., in Silicon Nitride Ceramics: Scientific and Technological Advances, edited by Chen, I-W., Becher, P.F., Mitomo, M., Petzow, G., and Yen, T-S. (Mater. Res. Soc. Symp. Proc. 287, Pittsburgh, PA, 1993) p. 159.Google Scholar
9.Kleebe, H-J., Hoffmann, M.J., and Ruhle, M., Z. Metallkde 83 (8) (1992) p. 610.Google Scholar
10.Kleebe, H-J., J. Mater. Sci. 29 (1994) p. 1265.CrossRefGoogle Scholar
11.Clarke, D.R., J. Amer. Ceram. Soc. 70 (1) (1987) p. 15.CrossRefGoogle Scholar
12.Kleebe, H-J., Cinibulk, M.K., Tanaka, I., Bruley, J., Vetrano, J.S., and Ruhle, M., in Tailoring of Mechanical Properties of Si3N4 Ceramics, edited by Hoffmann, M.J. and Petzow, G. (NATO ASI Series, Kluwer Academic Publishers, Dordrecht, 1994) p. 259.CrossRefGoogle Scholar
13.Pompe, W. and Kessler, H., in Tailoring of Mechanical Properties of Si3N4 Ceramics, edited by Hoffmann, M.J. and Petzow, G. (NATO ASI Series, Kluwer Academic Publishers, Dordrecht, 1994) p. 353.CrossRefGoogle Scholar
14.Kim, D.J., Greil, P., and Petzow, G., Adv. Ceram. Mater. 2 (1987) p. 817.CrossRefGoogle Scholar
15.Jack, K.H., J. Mater. Sci. 11 (1976) p. 1135.CrossRefGoogle Scholar
16.Weiss, J., Annu. Rev. Mater. Sci. 11 (1981) p. 381.CrossRefGoogle Scholar
17.Hampshire, S., Park, H.K., Thompson, D.P., and Jack, K.H., Nature 274 (1978) p. 880.CrossRefGoogle Scholar
18.Mitomo, M., Tanaka, H., Muramatsu, K., Ji, N., and Fujii, Y., J. Mat. Sci. Lett. 15 (1980) p. 2661.CrossRefGoogle Scholar
19.Ekström, T., in Silicon Nitride Ceramics: Scientific and Technological Advances, edited by Chen, I-W, Becher, P.F., Mitomo, M., Petzow, G., and Yen, T-S. (Mater. Res. Soc. Symp. Proc. 287, Pittsburgh, PA, 1993) p. 122.Google Scholar
20.Jack, K.H., in Silicon Nitride Ceramics: Scientific and Technological Advances, edited by Chen, I-W, Becher, P.F., Mitomo, M., Petzow, G., and Yen, T-S. (Mater. Res. Soc. Symp. Proc. 287, Pittsburgh, PA, 1993) p. 15.Google Scholar
21.Hoffmann, M.J., in Tailoring of Mechanical Properties of Si3N4 Ceramics, edited by Hoffmann, M.J. and Petzow, G. (NATO ASI Series, Kluwer Academic Publishers, Dordrecht, 1994) p. 233.CrossRefGoogle Scholar
22.Quinn, G.D. and Wirth, G., J. Euro. Ceram. Soc. 6 (1990) p. 169.CrossRefGoogle Scholar
23.Wiederhorn, S.M., Hockey, B.J., and Chuang, T-J., in Toughening Mechanisms in Quasi-Brittle Materials, edited by Shah, S.P. (Kluwer Academic Publishers, Netherlands, 1991) p. 555.CrossRefGoogle Scholar
24.Wilkinson, D., in Tailoring of Mechanical Properties of Si3N4 Ceramics, edited by Hoffmann, M J. and Petzow, G. (NATO ASI Series, Kluwer Academic Publishers, Dordrecht, 1994) p. 327.CrossRefGoogle Scholar
25.Wiederhorn, S.M., Luecke, W.E., Hockey, B.J., and Long, G.G., in Tailoring of Mechanical Properties of Si3N4 Ceramics, edited by Hoffmann, M J. and Petzow, G. (NATO ASI Series, Kluwer Academic Publishers, Dordrecht, 1994) p. 305.CrossRefGoogle Scholar