Hostname: page-component-586b7cd67f-2brh9 Total loading time: 0 Render date: 2024-11-24T08:34:14.895Z Has data issue: false hasContentIssue false

Phase equilibrium and mechanical properties of Cr-Mo-Nb-Si-B alloys Composed of BCC and T2-silicide phase

Published online by Cambridge University Press:  22 February 2019

Daisuke Goto*
Affiliation:
Graduate student, Department of Materials Science and Engineering, Hokkaido University, Kita13 Nishi 8, Kita-ku, Sapporo060-8628, Japan
Ken-ichi Ikeda
Affiliation:
Division of Materials Science and Engineering, Faculty of Engineering, Hokkaido University, Kita13 Nishi 8, Kita-ku, Sapporo060-8628, Japan.
Seiji Miura
Affiliation:
Division of Materials Science and Engineering, Faculty of Engineering, Hokkaido University, Kita13 Nishi 8, Kita-ku, Sapporo060-8628, Japan.
*
*Corresponding author: [email protected])
Get access

Abstract

A new class of high-temperature materials based on refractory elements was investigated with an aim to improve the energy efficiency of thermal power plants. Alloys based on Nb and Mo composed of BCC solid solution (BCCss) (Nb-Mo) and T2-silicide (Nb,Mo)5(Si,B)3 are promising candidates as high-temperature materials. Further investigation on the alloy phase equilibria of this system is required to improve the mechanical properties and oxidation resistance through optimization of the phase compositions. Cr is one candidate to modify the properties of the alloy because Cr is expected to stabilize the T2 compound phase along with B. Here, the phase equilibria among BCCss and the T2 compound are widely investigated in the Cr-Mo-Nb-Si-B system, and a BCCss-T2 two-phase microstructure is found in Mo-rich alloys. The B/Si ratio in the T2 phase increases with the Cr content, while almost no B solubility was found in BCCss. As the Si content increases in alloys, the A15 silicide phase ((Cr, Mo, Nb)3Si) and/or Laves phase appear.

Nanoindentation tests were conducted to investigate the mechanical properties of the BCCss phase of the alloys in the Cr-Mo-Nb-Si-B system. The nanohardness and reduced elastic modulus of these alloys tended to be higher with an increase in Cr.

Type
Articles
Copyright
Copyright © Materials Research Society 2019 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

Dimiduk, D.M. and Perepezko, J.H., Mater. Res. Soc. Bull., Vol. 9, 639-645 (2003).CrossRefGoogle Scholar
Bewlay, B.P., Jackson, M.R., Zhao, J.-C., Subramanian, P.R., Mendiratta, M.G., and Lewandowski, J.J., Mater. Res. Bull., Vol. 9, 646-653 (2003).CrossRefGoogle Scholar
Sakidja, R. and Perepezko, J.H., Metall. Mater. Trans. A, Vol. 36(3), 507-514 (2005).CrossRefGoogle Scholar
Subramanian, P.R., Mendiratta, M.G., Dimiduk, D.M., and Stucke, M.A., Mater. Sci. Eng., A, Vol. 239, 1-13 (1997).CrossRefGoogle Scholar
Constantinides, G., Ravi Chandran, K.S., Ulm, F.-J., and Van Vliet, K.J., Mater. Sci. Eng., A, Vol. 430, 189-202 (2006).CrossRefGoogle Scholar
Genga, J., Shao, G., and Tsakiropoulos, P., Intermetallics, Vol. 14(7), 832-837 (2006).CrossRefGoogle Scholar
Goldschmidt, H.J. and Brand, J. A., J. Less-Common Met., Vol. 3, 44-61 (1961).CrossRefGoogle Scholar