Hostname: page-component-586b7cd67f-t8hqh Total loading time: 0 Render date: 2024-11-24T09:34:52.906Z Has data issue: false hasContentIssue false
  • English
  • Français

Effect of Gradual Precipitation of α2 Particles on Mechanical Properties of Ti–6Al–4V Alloy

Published online by Cambridge University Press:  02 January 2019

Martín Ricardo Barajas-Alvarez ,
Alberto Ruiz  and
Víctor H. López-Morelos
Martín Ricardo Barajas-Alvarez
Affiliation:
Universidad Michoacana de San Nicolás de Hidalgo, Instituto de Investigación en Metalurgia y Materiales, Edificio U, Ciudad Universitaria, Morelia; Michoacán, México.
Alberto Ruiz*
Affiliation:
Universidad Michoacana de San Nicolás de Hidalgo, Instituto de Investigación en Metalurgia y Materiales, Edificio U, Ciudad Universitaria, Morelia; Michoacán, México.
Víctor H. López-Morelos
Affiliation:
Universidad Michoacana de San Nicolás de Hidalgo, Instituto de Investigación en Metalurgia y Materiales, Edificio U, Ciudad Universitaria, Morelia; Michoacán, México.
*
*(Email: [email protected])
Get access

Abstract

The present investigation focused on evaluating the effects of different amounts of precipitates on tension and hardness properties of a Ti–6Al–4V alloy, for this, two sets of samples with bimodal and equiaxed microstructures were obtained by heat treatment process. After this, the samples were aged at 545 °C for holding times of 100 and 200 h. Observation of the aged samples in the scanning electron microscope revealed fine α2 (Ti3Al) particles precipitating in the α matrix of the alloy. Uni-axial tension tests and Vickers microhardness measurements were conducted on the unaged and aged samples. Experimental results show that ultimate strength and hardness of bimodal and equiaxed microstructures are significantly affected by the heat treatment applied to produce such microstructures. Also, it was found that the precipitation of α2 particles drastically reduced the plastic response of the Ti–6Al–4V alloy.

Keywords

embrittlementmicrostructurescanning electron microscopy (SEM)
Type
Articles
Information
MRS Advances , Volume 3 , Issue 62: International Materials Research Congress XXVII , 2018 , pp. 3629 - 3634
Copyright
Copyright © Materials Research Society 2018 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

Jovanovic, M.T., et al. , The effect of annealing temperatures and cooling rates on microstructure and mechanical properties of investment cast Ti-6Al-4V alloy. Materials and Design, 2006. 27(3): p. 192-199.CrossRefGoogle Scholar
Lee, D.-G., et al. , Effects of volume fraction of tempered martensite on dynamic deformation properties of a Ti-6Al-4V alloy having a bimodal microstructure. Metallurgical and Materials Transactions A, 2005. 36 (13): p. 741-748.CrossRefGoogle Scholar
Li, H., Zhang, Y., and Yang, D., Micro-damage of Ti–6Al–4V alloy under hypervelocity projectile impact . Materials Science and Engineering: A, 2000. 292(1): p. 130-132.CrossRefGoogle Scholar
Lee, D.-G., Lee, S., and Lee, Y., Effect of precipitates on damping capacity and mechanical properties of Ti–6Al–4V alloy . Materials Science and Engineering: A, 2008. 486(1): p. 19-26.CrossRefGoogle Scholar
Lütjering, G. and Williams, J.C., Titanium. 2010, Berlin; New York: Springer.Google Scholar