Hostname: page-component-586b7cd67f-rcrh6 Total loading time: 0 Render date: 2024-11-24T12:47:15.636Z Has data issue: false hasContentIssue false
  • English
  • Français

Characterization of the texture evolution in AISI 430 and AISI 433 ferritic stainless steels during simulated hot rolling

Published online by Cambridge University Press:  29 April 2018

K. A. Annan ,
C.W. Siyasiya  and
W.E. Stumpf
K. A. Annan*
Affiliation:
Department of Materials Science and Metallurgical Engineering, University of Pretoria0002, South Africa.
C.W. Siyasiya
Affiliation:
Department of Materials Science and Metallurgical Engineering, University of Pretoria0002, South Africa.
W.E. Stumpf
Affiliation:
Department of Materials Science and Metallurgical Engineering, University of Pretoria0002, South Africa.
*
*Corresponding author: KA Annan, e-mail: [email protected]
Get access

Abstract

Multi-pass compression tests were carried out on the Gleeble-1500D® and Gleeble-3800TM® thermo-mechanical simulators to investigate the effect of temperature, strain rate and inter-pass time on the development of the texture in ferritic stainless steels (FSS) AISI 430 and 433, the latter an Al-containing variant. Orientation Distribution Functions (ODFs) through the electron backscattered diffraction (EBSD) technique was employed to characterise and study the texture present in the steels after hot working. The mean flow stress analysis showed that, the dynamic recrystallization to dynamic recovery transition temperature decreases with an increase in strain rate in both grades of stainless steels possibly allowing texture optimisation at lower hot rolling temperatures. Higher finishing rolling temperatures, lower strain rates and longer inter-pass times led to improvement in the formation of the desired γ-fibre texture which contributes to ductility or drawability in these steels. Dynamic recrystallization which promotes the formation of the desired γ-fibre texture was found to occur in both AISI 430 and 433 at temperatures above 1000 °C and strain rates less than 5 s-1. Generally AISI 433 develops a stronger gamma texture than the AISI 430 when hot rolled under similar conditions.

Keywords

crystallizationmicrostructurescanning electron microscopy (SEM)texture
Type
Articles
Information
MRS Advances , Volume 3 , Issue 34-35: African Materials Research Society 2017 , 2018 , pp. 1985 - 2002
Copyright
Copyright © Materials Research Society 2018 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

Wu, P.D, Lloyd, D.J, Bosl, A., Jin, H., McEwen, S.R, Acta Materialia. 51 (2003) 1945–1957.Google Scholar
Shin, H.J, An, J.K, Park, S.H, Lee, D.N, Acta Mater. 51(2003) 4693–4706.CrossRefGoogle Scholar
Wu, P.D, Lloyd, D.J, Huang, Y., J. Materials Science and Engineering. 427(2006) 241–245.Google Scholar
Wu, P.D, Jin, H, Shi, Y, Lloyd, D.J, J. Materials Science and Engineering 423(2006) 300–305.Google Scholar
Raabe, D., Lucke, K., J. Materials Technology. 10 (1992) 457–464.Google Scholar
Raabe, D., Ylitalo, M., J. Metallurgical Transactions. 27A (1996) 49–57.Google Scholar
Hamada, J., Ono, N., Inoue, H., ISIJ Int. 51(2011)1740–1748.Google Scholar
Jinxia, L., Zhanying, L., Cairu, G., Zhaodong, W., Xianghua, L., Guodong, W., J. Materials Processing Technology. 2005; 167: 132–137.Google Scholar
Mirzadeh, H., Najafizadeh, A., J. Materials Science and Engineering; 527 (2010): 1160–1164.Google Scholar
McQueen, H.J, Jonas, J.J, Treatise on Materials Science and Technology. 6 (1975) 393.Google Scholar
Columbus Technical data CS430, 2012. www.columbusstainless.co.zaGoogle Scholar
Dieter, G., Mechanical Metallurgy. SI edition, McGraw – Hill, 1988. Pp. 78.Google Scholar
Engler, O., Randle, V. Introduction to texture analysis. 2ND ed. New York: Taylor and Francis Group, LLC, 2010.Google Scholar
Cabrera, J.M, Omar, A.A, Jonas, J.J, Prado, J.M, J. Metallurgical and Materials Transactions 28A (1997) 2233 – 2243.CrossRefGoogle Scholar
Stumpf, W.E, Lecture notes: Advanced course on phase transformations in metals and their alloys. University of Pretoria, Pretoria 2010, p 5.1-5 – 5.6-8Google Scholar
Bai, D.Q, Yue, S., W.P Sun, , Jonas, J.J, J. Metallurgical Transactions. 24(1993) 2151–2159.Google Scholar
Ryan, N.D, McQueen, H.J, J. of Mechanical Working Technology. 12(1986) 323–349.Google Scholar