Hostname: page-component-586b7cd67f-r5fsc Total loading time: 0 Render date: 2024-11-24T13:00:44.410Z Has data issue: false hasContentIssue false
  • English
  • Français

RETRACTED - High discharge capacities of Ti-based quasicrystal electrodes synthesized by mechanical alloying

Published online by Cambridge University Press:  12 April 2018

DEDETEMO KIMILITA PATRICK ,
AKITO TAKASAKI  and
ALICJA KLIMKOWICZ
DEDETEMO KIMILITA PATRICK*
Affiliation:
Global Course of Science and Engineering, Graduate School of Engineering and Science, Shibaura Institute of Technology, Toyosu, Koto-ku, Tokyo, 135-8548, Japan.
AKITO TAKASAKI
Affiliation:
Department of Engineering Science and Mechanics, Shibaura Institute of Technology, Toyosu, Koto-ku, Tokyo, 135-8548, Japan.
ALICJA KLIMKOWICZ
Affiliation:
Department of Engineering Science and Mechanics, Shibaura Institute of Technology, Toyosu, Koto-ku, Tokyo, 135-8548, Japan.
*
*Dedetemo Kimilita Patrick [email protected]
Get access

Abstract

Ti-based quasicrystals are well known to store a high capacity of hydrogen exceeding the density of liquid hydrogen. This fact is due to that TiZrNi contain a large number of tetrahedral sites formed with Ti and Zr atoms that are chemical affinity with hydrogen. TiZrNi quasicrystal absorbs hydrogen up to host metal ratio (H/M) value near to 2.0. The disadvantage is due to the low equilibrium pressure. To solve this problem, we substituted Ti with a small amount of vanadium (V), with the nominal composition Ti45−x VxZr38Ni17 (x = 5, 10, 15) and synthesized by mechanical alloying. The subsequent annealing in vacuum conditions converted the amorphous into an icosahedral quasicrystal (I-phase) with face-centered cubic (FCC) Ti2Ni-type crystal. As the results, we investigated the discharge capacity for both amorphous and quasicrystal electrodes using three electrodes system (working, reference and counter electrodes) at room temperature. The highest discharge capacities obtained were 81.45 mAh/g recorded for amorphous electrode and 318.4 mAh/g for quasicrystal whose compositions is Ti35V10Zr38Ni17 at discharge current density of 15 mA/g. X-ray diffraction measurement was performed to provide the structural information on materials before and after hydrogenation. Microstructures of the materials were studied using an electron scanning microscope and the chemical compositions were confirmed using an EDX-analysis.

Keywords

hydrogenationquasicrystalamorphousmechanical alloyingelectrochemical synthesis
Type
Articles
Information
MRS Advances , Volume 3 , Issue 38: African Materials Research Society 2017 , 2018 , pp. 2271 - 2279
Copyright
Copyright © Materials Research Society 2018 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES:

Levine, D. and Steinhardt, P.J, Phys. Rev Lett. 53 (1984) 2477–2480.CrossRefGoogle Scholar
Ball, M.D., Lloyd, D.J., Scripta Metall. 19 (1985) 1065–1068.CrossRefGoogle Scholar
Tsai, A.P., Inoue, A., Masumoto, T., Jpn. J. Appl. Phys. 26 (1987) L1505–L1507.CrossRefGoogle Scholar
Kelton, K.F., Kim, W.J., Stroud, R.M., Appl. Phys. Lett. 70 (1997), 3230–3232.CrossRefGoogle Scholar
Sato, T.J., Abe, E., Tsai, A.P., Jpn. J. Appl. Phys. 36 (1997) L1038–L1039.CrossRefGoogle Scholar
Lu, J.. Peter, K. Deffeyes, N.Yao, phys. Rev. Lett. 87 (2001) 275507–1CrossRefGoogle Scholar
Yang, D., Adv. Mat. Res. 510 (2012) 781–785Google Scholar
Takasaki, A., Kuroda, C., Hwa Lee, S., Yong Kim, J., J. Alloys Compd. 509S (2011) S782–S785.CrossRefGoogle Scholar
Takasaki, A., Huett, V.T., Kelton, K.F., J. Non-Crystalline Solids 334-335 (2004) 457–460.CrossRefGoogle Scholar
F Kelton, K., Hartzell, J.J., Hennig, R.G., Huett, V.T., Takasaki, A., Phil. Mag. 86 (2006) 957–964.CrossRefGoogle Scholar
Takasaki, A., Kuroda, Ch., Lee, S.-H., Kim, J.-Y., J. Alloys Comp. 509S (2011) S782–S785.CrossRefGoogle Scholar
Yamramura, S., Kim, HY., Kimura, H., Inoue, A., Arata, Y. J. Alloys Compd 329 (2002) 230–5.CrossRefGoogle Scholar
Takasaki, A., Imai, N., Kelton, K.F., in: Belin-Ferré, E., Feuerbacher, M., Ishi, Y., Sordelet, D.J. (Eds), Materials Research Society Symposium Proceedings, 805 Pittsburgh, PA (2004) 351–356.Google Scholar
Takasaki, A., Zajac, W., Okuyama, T., Szmyd, J.S., J. Electrochem. Soc. 156 (2009) A521–A526.CrossRefGoogle Scholar
Li, S., Zhao, M., Wang, L., Liu, Y., Wang, Y., Mater. Sci. Eng. B, 150 (2008) 168–74.CrossRefGoogle Scholar
Hiroshi, I., Norihiro, K., Masanobu, C., Eiji, H., Int. J. Hydrogen Energ. 41 (2016) 9939–9947.Google Scholar
Fadda, S., Cincotti, A., Concas, A., Pisu, M., Cao, G., Powder Technology. 194(3) (2009) 207–216.CrossRefGoogle Scholar
Bancel, P.A., Meiney, P.A., Stephens, P.W., Goldman, A.I., Horn, P.M., Phys. Rev. Lett. 54 (1985) 2422–2425.CrossRefGoogle Scholar
Takasaki, A., Okuyama, T., Szmyd, J.S., J. Matter. Res. 25(8) (2010) 1575–1582.CrossRefGoogle Scholar
Liu, B., Wu, Y., Wang, L., J. Power Sources 159 (2006) 1458–1463.CrossRefGoogle Scholar
Ariga, Y., Takasaki, A., Kimijima, T., Swierczek, K., J. Alloy. Compds. 645 (2015) S152–S154.CrossRefGoogle Scholar