Hostname: page-component-586b7cd67f-gb8f7 Total loading time: 0 Render date: 2024-11-24T12:50:20.919Z Has data issue: false hasContentIssue false
  • English
  • Français

Optimization of the Electrical Performance of Metal Oxide Thin-film Transistors by varying Spray Deposition Parameters

Published online by Cambridge University Press:  11 January 2018

Guilherme R. de Lima ,
João Paulo Braga ,
Giovani Gozzi  and
Lucas Fugikawa Santos
Guilherme R. de Lima
Affiliation:
Departamento de Física, Universidade Estadual Paulista - UNESP, Rua Cristovao Colombo 2265, CEP 15054-000, Sao Jose do Rio Preto, SP, Brazil.
João Paulo Braga
Affiliation:
Departamento de Física, Universidade Estadual Paulista - UNESP, Rua Cristovao Colombo 2265, CEP 15054-000, Sao Jose do Rio Preto, SP, Brazil.
Giovani Gozzi
Affiliation:
Departamento de Física, Universidade Estadual Paulista - UNESP, Avenida 24 A, 1515, CEP: 13500-970, Rio Claro, SP, Brazil.
Lucas Fugikawa Santos*
Affiliation:
Departamento de Física, Universidade Estadual Paulista - UNESP, Rua Cristovao Colombo 2265, CEP 15054-000, Sao Jose do Rio Preto, SP, Brazil. Departamento de Física, Universidade Estadual Paulista - UNESP, Avenida 24 A, 1515, CEP: 13500-970, Rio Claro, SP, Brazil.
*
*(Email: [email protected]; [email protected])
Get access

Abstract

Metal oxides like zinc oxide (ZnO) are promising materials for the active layer of thin-film transistors (TFTs) used in the drive circuit of next-generation large-area active matrix displays due to their high electronic mobility, high transmittance in the optical visible range and processability. Traditional deposition techniques employ RF sputtering or pulsed-laser deposition (PLD), which are relatively sophisticated techniques. The deposition of very thin (less than 50 nm thick) layers of ZnO using soluble organic precursors have been extensively investigated recently as an alternative to traditional deposition methods. Solution-based deposition processes include simple and affordable techniques like dip-coating, spin-coating, spray-pyrolysis and ink-jet printing. Spray-pyrolysis is particularly interesting due to the high film uniformity, low cost and high device performance. We carried out several experiments analyzing the performance of ZnO based devices using zinc acetate as organic precursor to confirm that spray pyrolysis deposition is a suitable technique for production of high-performance and reproducible TFTs. Moreover, we observed that device performance can significantly vary with little modifications on the deposition parameters, even for the same active layer composition and pyrolysis temperature. Electrical parameters, as the electrical mobility and the on/off ratio, varied several orders of magnitude, whereas the threshold voltage varied up to 20 V for the tested devices. Deposition parameters as the nozzle height during the deposition, nozzle air pressure and deposition time were varied until we obtained devices with optimum electrical performance. Optimized devices presented mobilities in the order of 1 cm2.V-1.s-1, on/off ratio of about 106 and relatively low operation voltages. A statistical analysis of a great number of devices manufactured using the same deposition parameters was also carried out to assure the reproducibility of the deposition technique.

Keywords

thin filmspray pyrolysiselectrical properties
Type
Articles
Information
MRS Advances , Volume 3 , Issue 5: Electronics, Magnetics and Photonics , 2018 , pp. 247 - 253
Check for updates
Copyright
Copyright © Materials Research Society 2018 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

Fortunato, E., Barquinha, P. and Martins, R., Adv. Mater. 24, 2945 (2011).Google Scholar
Kamiya, T., Nomura, K. and Hosono, H., Sci. Technol. Adv. Mater. 11, 044305 (2010).Google Scholar
Wang, Y., Liu, S. W., Sun, X. W., Zhao, J. L., Goh, G. K. L., Vu, Q. V., and Yu, H. Y.. J. Sol-Gel Sci. Technol. 55, 322 (2010).CrossRefGoogle Scholar
Kim, G. H., Kim, H. S., Shin, H. S., Du Ahn, B., Kim, K. H., and Kim, H. J.. Thin Solid Films 517, 4007 (2009).Google Scholar
Kim, G. H., Shin, H. S., Du Ahn, B., Kim, K. H., Park, W. J., and Kim, H. J.. J. Electrochem. Soc. 156, H7 (2009).Google Scholar
Zhao, Y., Dong, G., Duan, L., Qiao, J., Zhang, D., Wang, L., and Qiu, Y.. RSC Adv. 2, 5307 (2012).Google Scholar
Su, B.-Y., Chu, S.-Y., and Juang, Y.-D.. IEEE Trans. Electron Devices 59(3), 700 (2012).Google Scholar
Walker, D. E., Major, M., Yazdi, M. B., Klyszcz, A., Haeming, M., Bonrad, K., Melzer, C., Donner, W., and von Seggern, H.. ACS Appl. Mater. Interfaces 4, 6835 (2012).CrossRefGoogle Scholar
Meyers, S. T., Anderson, J. T., Hung, C. M., Thompson, J., Wager, J. F., and Keszler, D. A.. J. Am. Chem. Soc. 130, 17603 (2008).Google Scholar
Perednis, D. and Gauckler, L. J.. J. Electroceramics 14, 103 (2005).CrossRefGoogle Scholar
Krunks, M. and Mellikov, E.. Thin Solid Films 270, 33 (1995).Google Scholar
Banger, K. K., Yamashita, Y., Mori, K., Peterson, R. L., Leedham, T., Rickard, J., and Sirringhaus, H.. Nat. Mater. 10, 45 (2011).Google Scholar