Hostname: page-component-586b7cd67f-t7fkt Total loading time: 0 Render date: 2024-11-28T05:11:10.739Z Has data issue: false hasContentIssue false
  • English
  • Français

Highly Conductive Polymer Nanocomposite – Application inInterconnects and Traces

Published online by Cambridge University Press:  28 December 2015

Chenggang Chen ,
Sabyasachi Ganguli ,
Ajit K. Roy  and
Jason Foley
Chenggang Chen*
Affiliation:
Materials and Manufacturing Directorate, Air Force Research Laboratory, Wright Patterson Air Force Base, OH 45431, U.S.A. University of Dayton Research Institute, Dayton, OH 45469, U.S.A.
Sabyasachi Ganguli
Affiliation:
Materials and Manufacturing Directorate, Air Force Research Laboratory, Wright Patterson Air Force Base, OH 45431, U.S.A.
Ajit K. Roy
Affiliation:
Materials and Manufacturing Directorate, Air Force Research Laboratory, Wright Patterson Air Force Base, OH 45431, U.S.A.
Jason Foley
Affiliation:
Munitions Directorate, Air force Research Laboratory, Eglin Air Force Base, FL, 32542 U.S.A.
*
*(Email: [email protected])
Get access

Abstract

Commercial off-the-shelf (COTS) electronics are generally not specificallydesigned to perform in extremely transient high impact scenarios. This researchfocused on the development of a silver-decorated carbon black-based polymericnanocomposite with properties such as high conductivity, flexibility, and shockabsorbency. Polymeric rubber materials are generally very flexible and shockabsorbing, however, most polymeric materials are electrical insulators. Thedispersion of the silver-decorated carbon black into the polymeric matrix couldsignificantly improve the electrical conductivity. The processing andfabrication of Ag-CB (silver-carbon black)/Epoxy (thermosetting epoxy polymer)and Ag-CB/TPU (thermoplastic polyurethane) will be reported. Both Ag-CB/Epoxyand Ag-CB/TPU mixtures with solvents showed the shear-thinning behavior, whichwas an important characteristic for direct printing of traces and AdditiveManufacturing (AM). The mechanical properties of the nanocomposites weremeasured using Dynamic Mechanical Analysis (DMA) over a wide range oftemperatures. These nanocomposite materials were also successfully used to printflexible circuits using a 3D-printing machine. The electrical resistance changefor the Ag-CB/Epoxy on polydimethylsiloxane (PDMS) and Ag-CB/TPU on PDMS understrain was studied, and the results will be discussed.

Keywords

compositeelectronic materialnanostructure
Type
Articles
Information
MRS Advances , Volume 1 , Issue 1: Biomaterials and Soft Materials , 2016 , pp. 9 - 14
Copyright
Copyright © Materials Research Society 2015 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

Custer, W., IPC Outlook (www.ipc.org) (access on August 15, 2014).Google Scholar
Yao, S. and Zhu, Y., Adv. Mater. 27, 1480–1511 (2015).Google Scholar
Vaia, R. A. and Giannelis, E. P., MRS Bull. 26, 394 (2001).CrossRefGoogle Scholar
Luo, X. and Chung, D.D.L., J. Mater. Sci. 34, 273–276 (1999).Google Scholar
Tra-Con, Tra-Duct 2902, www.tra-con.com(access on January, 12, 2015).Google Scholar
EPO-TEK® H20E, www.epotek.com (access on September, 25, 2014).Google Scholar