Three-dimensional (3D) nondestructive microstructural characterization was performed using full-field transmission X-ray microscopy on an Sn-rich alloy, at a spatial resolution of 60 nm. This study highlights the use of synchrotron radiation along with Fresnel zone plate optics to perform absorption contrast tomography for analyzing nanoscale features of fine second phase particles distributed in the tin matrix, which are representative of the bulk microstructure. The 3D reconstruction was also used to quantify microstructural details of the analyzed volume.

An original high-pressure microscopy chamber has been designed for real-time visualization of biological cell growth during high isostatic (gas or liquid) pressure treatments up to 200 MPa. This new system is highly flexible allowing cell visualization under a wide range of pressure levels as the thickness and the material of the observation window can be easily adapted. Moreover, the design of the observation area allows different microscope objectives to be used as close as possible to the observation window. This chamber can also be temperature controlled. In this study, the resistance and optical properties of this new high-pressure chamber have been tested and characterized. The use of this new chamber was illustrated by a real-time study of the growth of two different yeast strains – Saccharomyces cerevisiae and Candida viswanathii – under high isostatic gas pressure (30 or 20 MPa, respectively). Using image analysis software, we determined the evolution of the area of colonies as a function of time, and thus calculated colony expansion rates.

A microchannel plate was used as an ion sensitive detector in a commercial helium ion microscope (HIM) for dark-field transmission imaging of nanomaterials, i.e. scanning transmission ion microscopy (STIM). In contrast to previous transmission HIM approaches that used secondary electron conversion holders, our new approach detects forward-scattered helium ions on a dedicated annular shaped ion sensitive detector. Minimum collection angles between 125 mrad and 325 mrad were obtained by varying the distance of the sample from the microchannel plate detector during imaging. Monte Carlo simulations were used to predict detector angular ranges at which dark-field images with atomic number contrast could be obtained. We demonstrate atomic number contrast imaging via scanning transmission ion imaging of silica-coated gold nanoparticles and magnetite nanoparticles. Although the resolution of STIM is known to be degraded by beam broadening in the substrate, we imaged magnetite nanoparticles with high contrast on a relatively thick silicon nitride substrate. We expect this new approach to annular dark-field STIM will open avenues for more quantitative ion imaging techniques and advance fundamental understanding of underlying ion scattering mechanisms leading to image formation.

Yttria-stabilized tetragonal zirconia polycrystals (3Y-TZP) is a ceramic material used in indirect dental restorations. However, phase transformation at body temperature may compromise the material’s mechanical properties, affecting the clinical performance of the restoration. The effect of mastication on 3Y-TZP aging has not been investigated. 3Y-TZP specimens (IPS E-max ZirCAD and Z5) were aged in three different modes (n=13): no aging (control), hydrothermal aging (HA), or chewing simulation (CS). Mechanical properties and surface topography were analyzed. Analysis of variance showed that neither aging protocol (p=0.692) nor material (p=0.283) or the interaction between them (p=0.216) had a significant effect on flexural strength, values ranged from 928.8 MPa (IPSHA) to 1,080.6 MPa (Z5HA). Nanoindentation analysis showed that material, aging protocol, and the interaction between them had a significant effect (p<0.001) on surface hardness and reduced Young’s modulus. The compositional analysis revealed similar yttrium content for all the experimental conditions (aging: p=0.997; material: p=0.248; interaction material×aging: p=0.720). Atomic force microscopy showed an effect of aging protocols on phase transformation, with samples submitted to CS exhibiting features compatible with maximized phase transformation, such as increased volume of the material microstructure at the surface leading to an increase in surface roughness.

The nature of nanocrystalline inclusions and dopant distribution in bismuth-doped silicate fibers and preforms are studied by scanning and transmission electron microscopy, and energy and wavelength-dispersive X-ray microanalysis. The core compositions are Bi:SiO2, Bi:Al2O3–SiO2, Bi:GeO2–SiO2, Bi:Al2O3–GeO2–SiO2, and Bi:P2O5–Al2O3–GeO2–SiO2. Nanocrystals of metallic Bi, Bi2O3, SiO2, GeO2, and Bi4(GeO4)3 are observed in these glasses. These inclusions can be the reason for the background optical loss in bismuth-doped optical fibers. The bismuth concentration of 0.0048±0.0006 at% is directly measured in aluminosilicate optical fibers with effective laser generation (slope efficiency of 27% at room temperature).

High-pressure die-casting (HPDC) AM50 tensile specimens were used to investigate characteristics of gas pores and its effect on mechanical properties of HPDC AM50 magnesium alloy. Combining microstructure morphology gained from optical microscopy, scanning electron microscopy (SEM), and three-dimensional (3D) reconstruction with the experimental data from uniaxial tensile testing, we pursued the relationship between gas pores and the mechanical properties of HPDC AM50 Mg alloy. Results indicate that comparing with 3D reconstruction models, 2D images like optical metallography images and SEM images have one-sidedness. Furthermore, the size and maximum areal fraction of gas pores have negative effects on the mechanical properties of HPDC AM50 Mg alloy. With increase of the maximum size of gas pores in the specimen, the ultimate tensile strength (UTS) and elongation decrease. In addition, with the maximum areal fraction becoming larger, both the UTS and elongation decrease linearly.

Studies on fixed samples or genome-wide analyses of nuclear processes are useful for generating snapshots of a cell population at a particular time point. However, these experimental approaches do not provide information at the single-cell level. Genome-wide studies cannot assess variability between individual cells that are cultured in vitro or originate from different pathological stages. Immunohistochemistry and immunofluorescence are fundamental experimental approaches in clinical laboratories and are also widely used in basic research. However, the fixation procedure may generate artifacts and prevents monitoring of the dynamics of nuclear processes. Therefore, live-cell imaging is critical for studying the kinetics of basic nuclear events, such as DNA replication, transcription, splicing, and DNA repair. This review is focused on the advanced microscopy analyses of the cells, with a particular focus on live cells. We note some methodological innovations and new options for microscope systems that can also be used to study tissue sections. Cornerstone methods for the biophysical research of living cells, such as fluorescence recovery after photobleaching and fluorescence resonance energy transfer, are also discussed, as are studies on the effects of radiation at the individual cellular level.

The new generation of energy-dispersive X-ray (EDX) detectors with higher count rates than ever before, paves the way for a new approach to quantitative elemental analysis in the scanning transmission electron microscope. Here we demonstrate a method of calculating partial cross sections for use in quantifying EDX data, beneficial especially because of the simplicity of its implementation. Applying this approach to acid-leached PtCo catalyst nanoparticles leads to quantitative determination of the Pt surface enrichment.

Scanning electron microscope-cathodoluminescence (SEM-CL) analysis was performed for neodymium–iron–boron (NdFeB) and samarium–cobalt (Sm–Co) magnets to analyze the rare-earth elements present in the magnets. We examined the advantages of SEM-CL analysis over conventional analytical methods such as SEM-energy-dispersive X-ray (EDX) spectroscopy and SEM-wavelength-dispersive X-ray (WDX) spectroscopy for elemental analysis of rare-earth elements in NdFeB magnets. Luminescence spectra of chloride compounds of elements in the magnets were measured by the SEM-CL method. Chloride compounds were obtained by the dropwise addition of hydrochloric acid on the magnets followed by drying in vacuum. Neodymium, praseodymium, terbium, and dysprosium were separately detected in the NdFeB magnets, and samarium was detected in the Sm–Co magnet by the SEM-CL method. In contrast, it was difficult to distinguish terbium and dysprosium in the NdFeB magnet with a dysprosium concentration of 1.05 wt% by conventional SEM-EDX analysis. Terbium with a concentration of 0.02 wt% in an NdFeB magnet was detected by SEM-CL analysis, but not by conventional SEM-WDX analysis. SEM-CL analysis is advantageous over conventional SEM-EDX and SEM-WDX analyses for detecting trace rare-earth elements in NdFeB magnets, particularly dysprosium and terbium.

Iron is an essential trace element that plays important roles in the cellular function of all organs and systems. However, the function of Fe(II) in mammalian embryo development is unknown. In this study, we investigated the role of Fe(II) during preimplantation embryo development. Depletion of Fe(II) using thiosemicarbazone-24 (TSC24), a specific Fe(II) chelator, rescued quenching of the Fe(II)-sensitive fluorophore phen green-SK. After in vitro fertilization, TSC24 significantly reduced the cleavage rate as well as blastocyst formation. The hatch rate of blastocysts was also reduced with 1 pM TSC24 treatment (20.25±1.86 versus 42.28±12.96%, p<0.05). Blastocysts were cultured in leukemia inhibitory factor-free mouse embryonic stem cell culture medium with or without TSC24, and those with depleted Fe(II) displayed delayed attachment and lost the ability to induce embryoid body formation. To further explore the mechanism of Fe(II) in embryo development, we assessed the expression of 5-hydroxymethylcytosine (5hmC) and OCT4 in the pronuclear and blastocyst stages, respectively. We observed that Fe(II) reduced 5hmC and OCT4 expression, which could be explained by low ten-eleven translocation (TET) enzyme activity induced by TSC24 treatment. These findings demonstrate that Fe(II) is required for mammalian embryo development and that it facilitates the process via regulation of TET activity.

Grain boundaries (GB) are characterized by disorientation of the neighboring grains and the direction of the boundary plane between them. A new approach presented here determines the projection of GB that can be used to determine the latter one. The novelty is that an additional parameter of GB is quantified in addition to the ones provided by the orientation maps, namely the width of the projection of the GB is measured from the same set of diffraction patterns that were recorded for the orientation map, without the need to take any additional images. The diffraction patterns are collected in nanobeam diffraction mode in a transmission electron microscope, pixel-by-pixel, from an area containing two neighboring grains and the boundary between them. In our case, the diffraction patterns were recorded using the beam scanning function of a commercially available system (ASTAR). Our method is based on non-negative matrix factorization applied to the mentioned set of diffraction patterns. The method is encoded in a MATLAB environment, making the results easy to interpret and visualize. The measured GB-projection width is used to determine the orientation of the GB-plane, as given in the study by Kiss et al.

The aim of this study was to compare surface structures of laser-irradiated dental hard tissues using confocal (CFM), atomic force (AFM), and scanning electron microscopy (SEM). The general potential of the AFM in analyzing laser-irradiated surfaces was determined in this context. Specimens of human enamel and dentin were irradiated using an 8.6 W Nd:YVO4 laser with a pulse duration of 8 ps, λCenter=1,064 nm, and a pulse repetition rate of 500 kHz. Surface topology of irradiated areas (1 mm2) was investigated using AFM, CFM, and SEM. Surface roughness Rz was measured only with the AFM and the CFM. For non-irradiated enamel and dentin surfaces, roughnesses for CFM and AFM are in the nanometer range. However, major differences in roughness were determined for laser-prepared surfaces. For enamel, Rz(CFM)=2.33 μm is much higher compared with Rz(AFM)=0.09 μm; in the case of dentin, Rz(CFM)=5.35 μm is also much higher compared with Rz(AFM)=0.093 μm. Information regarding structural properties of surfaces needs real dimensions, particularly for use in dentistry. In this respect, AFM technology provides no additional results that lead to a significant improvement.

In this paper, the change detection of a fast turning specimen is studied at micro-level, whereas the images are acquired without stopping the rotation. In the beginning of the experiment, the imaging system is focused on the surface of the specimen. By starting the rotation of the specimen, the diameter of the specimen changes due to wear, which results in de-focusing of the imaging system. So the amount of blur in the images can be used as evidence of the wear phenomenon. Due to the properties of the microscope, the corners of the frames were dark and had to be cropped. So, each micrograph reflects only a small area of the surface. Nevertheless, techniques like stitching of multiple images can provide a significant surface area for micro-level investigation which increases the effectiveness of analyzing the material modification. Based on the results computer vision could detect a change of about 1.2 µm in the diameter of the specimen. More important is that we could follow the same locations of the surface in the microscopic images despite blurring, uneven illumination, change on the surface, and relatively a high-speed rotation.