Hostname: page-component-cd9895bd7-jn8rn Total loading time: 0 Render date: 2024-12-27T07:17:24.990Z Has data issue: false hasContentIssue false
  • English
  • Français

Investigating the effect of titanium addition on the wearresistance of Hadfield steel

Published online by Cambridge University Press:  12 December 2014

V.N. Najafabadi ,
K. Amini  and
M.B. Alamdarlo
V.N. Najafabadi
Affiliation:
Department of Materials Science and Engneering, NajafAbad Branch, Islamic Azad University, Isfahan, Iran
K. Amini
Affiliation:
Department of Mechanical Engineering, Tiran Branch, Islamic Azad University, Isfahan, Iran. e-mail: [email protected]
M.B. Alamdarlo
Affiliation:
Department of Materials Science and Engneering, NajafAbad Branch, Islamic Azad University, Isfahan, Iran
Get access

Abstract

In this study, the effect of titanium addition on the microstructure and wear behavior ofHadfield steel was investigated. To do so, four groups of samples with different titaniumcontents of 0, 0.2, 0.4 and 0.6 wt% were prepared. After casting, the samples wereaustenitized at 1100 °C for 3h and quenched in water subsequently for solution treatment. Themicrostructure of the samples was investigated using an optical microscope (OM) andscanning electron microscope (SEM). For more studies the carbide composition was analyzedvia energy-dispersive spectroscopy (EDX). A wear test was performed via a pin-on-disk weartesting machine. The results show that after heat treatment the microstructure of thetitanium-free sample is fully austenitic, while the other samples show an austeniticstructure with non-continuous carbide precipitates. It was also revealed that titaniumaddition improves the hardness and wear resistance of the samples. The highest wearresistance was observed in the sample with 0.6 wt% titanium content. It was also shownthat the predominant wear mechanisms are adhesive and tribo-chemical. Beyond this, theeffect of cold working via a hammering treatment was studied on the samples and revealedthat austenite-to-martensite transformation improves the hardness and wear resistancesignificantly.

Keywords

Hadfield steeltitanium carbidewear resistancehardness
Type
Research Article
Information
Metallurgical Research & Technology , Volume 111 , Issue 6 , 2014 , pp. 375 - 382
Copyright
© EDP Sciences 2014

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

S., Hofer, M., Hartl, G., Schestak, R., Schneider, E., Arenholz, L., Samek, Journal of Mining, Metallurgical, Materials, Geotechnical, and Plant Engineering 156 (2011) 99-104
Dastur, Y.N., Leslie, W.C., Metall. Mater. Trans. A 18 (1987) 1629-1639
Smith, R.W., DeMonte, A., Mackay, W.B.F., J. Mater. Process. Tech. 153-154 (2004) 589-595
Rama, R., Kutumbarao, V.V., Int. Mater. Rev. 34 (1989) 69-86
A. Andreussi, P. Andreussi, E. Veneroso, E. Pontelli, Method to obtain manganese steel alloy, United states patent, No. 11, 2007
Srivastava, A.K., DAS, K., ISIJ Int. 49 (2009) 1372-1377
Bedolla-Jacuinde, A., Correa, R., Quezada, J.G., Maldonado, C., Mat. Sci. Eng. A 398 (2005) 297-308
Jiang, W.H., Pan, W.D., Ren, Y.L., Han, X.L., Mater. Sci. Lett. 17 (1998) 1527-1529
O.V., Yablokova, S.N., Kul’kov, Powder Metall. Met. C+ 29 (1990) 520-522
Liu, Y.J., Ye, Y., Yang, Z., He, D.S., Surf. Coat. Tech. 204 (2009) 705-712
A.A., Astaf’ev, Met. Sci. Heat Treat. 39 (1997) 198-201
G.A., Fontalvo, R., Humer, C., Mitterer, K., Sammt, I., Schemmel, Wear 260 (2006) 1028-1034