Hostname: page-component-cd9895bd7-8ctnn Total loading time: 0 Render date: 2024-12-25T18:29:08.125Z Has data issue: false hasContentIssue false
  • English
  • Français

A 3D comprehensive finite element based simulation for bestShrink Fit design process

Published online by Cambridge University Press:  02 April 2013

Hossein Golbakhshi ,
Moslem Namjoo  and
Meisam Mohammadi
Hossein Golbakhshi
Affiliation:
Department of Agricultural Machinery Engineering, Faculty of Agriculture, University of Jiroft, Jiroft, Iran
Moslem Namjoo
Affiliation:
Department of Agricultural Machinery Engineering, Faculty of Agriculture, University of Jiroft, Jiroft, Iran
Meisam Mohammadi*
Affiliation:
Young Researchers and Elites Club, Kerman Branch, Islamic Azad University, Kerman, Iran
*
a Corresponding author:[email protected]
Get access

Abstract

Shrink fits are low-price connections which are widely used in industry and industrialconnections. In designing shrink fits it is important to consider radial interface foroptimized performance and also to choose an accurate method of fabrication and assembling.Parts which have to be assembled are usually exposed to thermo-mechanical loads. Mode andtime duration of heat transfer have a significant effect on required hydraulic force,stress time rate of creation in parts and joint ability to withstand against externalloads. Therefore, planning a set of appropriate thermal and structural procedures hassignificant role in reducing energy consumption, optimized performance and promoting thespeed of parts assembly. Despite of the fact, few researches have been done on shrink fitoperation and design, rather than dimensional design. In this study, shrink fits arestudied in two main processes: first heating and mounting process and then backing to theambient condition. A 3D coupled thermal and structural simulation based on FEM is done oneach process through well-known Solidworks Premium. To evaluate the accuracy, exactanalytical solution of two steel rings shrink fit is compared with the approach outcomes.Results of validated method are used for choosing the most optimum sub processes of shrinkfit fabrication.

Keywords

Shrink fit connectioncoupled thermal–mechanical analysisdesign processfinite elementsolidworks
Type
Research Article
Information
Mechanics & Industry , Volume 14 , Issue 1 , 2013 , pp. 23 - 30
Copyright
© AFM, EDP Sciences 2013

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

Truman, C.E., Booker, J.D., Analysis of a Shrink Fit Failure on a Gear Hub/Shaft Assembly, Eng. Fail. Anal. 14 (2007) 557–572 CrossRefGoogle Scholar
Pedersen, P., On shrink fit analysis and design, Comput. Mech. 37 (2006) 121–130 CrossRefGoogle Scholar
Antoni, N., Gaisne, F., Analytical Modeling for Static Stress Analysis of Pin-Loaded Lugs with Bush-Fitting, Appl. Math. Model. 35 (2011) 1–21 CrossRefGoogle Scholar
K.J. Gohnson, Contact Mechanics, Cambridge University Press, Cambridge, UK, 1985
J.E. Shigley, C.R. Mischke, Standard Handbook of Machine Design, McGraw-Hill, New York, 1985
A.C. Ugural, S.K. Fenseter, Advanced Strength and Applied elasticity, PTR Prentice- Hall, Englewood Cliffs (NJ), 1987
Sen, S., Aksakal, B., Stress Analysis of Interference Fitted Shaft-Hub System under Transient Heat Transfer Conditions, Mater. Des. 25 (2005) 407–417 CrossRefGoogle Scholar
Parasad, N.S., Sashikant, P., Ramamurt, V., Stress Distribution in Interference Joints, J. Compos. Struct. 51 (1994) 535–540 CrossRefGoogle Scholar
Ozel, A., Temiz, S., Aydin, M.D., Sen, S., Stress Analysis of Shrink-fitted Joints for Various Fit Forms via Finite Element Method, Mater. Des. 26 (2005) 281–290 CrossRefGoogle Scholar
Mack, W., Bengri, M., Thermal Assembly of an Elastic-Plastic Shrink Fit with Solid Inclusion, Int. J. Mech. Sci. 36 (1994) 699–705 CrossRefGoogle Scholar
Zhang, Y., McClain, B., Fang, X.D., Design of interference fits via finite element, Int. J. Mech. Sci. 42 (2000) 1835–1850 CrossRefGoogle Scholar
V.T. Morgan, The overall convective heat transfer from smooth circular cylinders, in: T.F. Irvine, Jr, J.P. Hartnett (eds.), Adv. Heat Transf. 11 (1975) 199–264
B.B. Mikic, W.M. Rohsenow, Thermal contact resistance, Department of Mechanical Engineering, Massachusetts Institute of Technology, 1966