Hostname: page-component-586b7cd67f-2brh9 Total loading time: 0 Render date: 2024-11-24T19:45:35.779Z Has data issue: false hasContentIssue false
  • English
  • Français

Numerical Simulation Study on Battery-Casing Sealing Considering Rubber Aging

Published online by Cambridge University Press:  14 October 2020

Yijie Huang ,
Fei Guo Open the ORCID record for Fei Guo [Opens in a new window] ,
Yuchao Ke ,
Fangyong Wu ,
Xiaohong Jia  and
Yuming Wang
Yijie Huang
Affiliation:
State Key Laboratory of Tribology, Tsinghua University, Beijing, China Joint Research Center for Rubber and Plastic Seals, Tsinghua University, Beijing, China
Fei Guo*
Affiliation:
State Key Laboratory of Tribology, Tsinghua University, Beijing, China Joint Research Center for Rubber and Plastic Seals, Tsinghua University, Beijing, China
Yuchao Ke
Affiliation:
Joint Research Center for Rubber and Plastic Seals, Tsinghua University, Beijing, China Anhui Zhongding Sealing Parts Co., Ltd., Ningguo, China
Fangyong Wu
Affiliation:
Zhejiang Hangze Intelligent Technology Co., Ltd.Wenzhou, China
Xiaohong Jia
Affiliation:
State Key Laboratory of Tribology, Tsinghua University, Beijing, China Joint Research Center for Rubber and Plastic Seals, Tsinghua University, Beijing, China
Yuming Wang
Affiliation:
State Key Laboratory of Tribology, Tsinghua University, Beijing, China Joint Research Center for Rubber and Plastic Seals, Tsinghua University, Beijing, China
*
*Corresponding author ([email protected])
Get access

Abstract

Battery-casing sealing is the key factor for secure travel of new energy vehicles. We constructed a relatively accurate mechanical-simulation model by selecting a constitutive model, analyzing the influence of thermal elongation, verifying the grid-independence and comparing numerically by the pressure-measurement film on the basis of studying the physical performance of a certain type of sealing material that had been used in battery-casings after aging. Based on a porous-media model and combined with changes of macroscopic and microscopic contact characteristics of materials at different times after aging, the evolution rule of sealing performance with time was analyzed quantitatively by calculating the leakage. By analyzing the structure of circular arc bulge on the surface of sealing material, the radius of circular arc bulge with better sealing performance was obtained, which could reduce the leakage of sealing structure during the material’s lifecycle.

Keywords

battery-casingmechanical-simulation modelagingleakagesealing performance
Type
Research Article
Information
Journal of Mechanics , Volume 36 , Issue 6 , December 2020 , pp. 955 - 969
Copyright
Copyright © 2020 The Society of Theoretical and Applied Mechanics

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

Song, L, Lu, A, Feng, P, Lu, Z, “Preparation of silicone rubber foam using supercritical carbon dioxide”, Materials Letters, 121, pp. 126-128 (2014).CrossRefGoogle Scholar
Wu, J, Niu, K, Su, B, Wang, Y, “Effect of combined UV thermal and hydrolytic aging on micro-contact properties of silicone elastomer”, Polymer Degradation and Stability, 151, pp. 126-135 (2018).CrossRefGoogle Scholar
Huang, Y J, et al, “The deterioration of foamed silicone rubber in humid and hot environments”, Journal of Cellular Plastics, 55, pp. 633-654 (2019).Google Scholar
Sharma, B.K., Krishnanand, K., Mahanwar, P.A., Sarma, K.S.S., Ray Chowdhury, S., “Gamma radiation aging of EVA/EPDM blends: Effect of vinyl acetate (VA) content and radiation dose on the alteration in mechanical, thermal, and morphological behavior”, Journal of Applied Polymer Science, 135, (2018).CrossRefGoogle Scholar
Ismail, H., Che Mat, N.S., Othman, N., “Curing characteristics, tear, fatigue, and aging properties of bentonite-filled ethylene-propylene-diene (EPDM) rubber composites”, Journal of Vinyl and Additive Technology, 24, pp. 77-84 (2018).CrossRefGoogle Scholar
Aoyagi, Y., Giese, U., Jungk, J., Beck, K., “The analysis of aging processes of EPDM elastomers using low field NMR with inverse laplace transform and stress relaxation measurements”, KGK Kautschuk Gummi Kunststoffe, 71, pp. 26-35 (2018).Google Scholar
Rahmah, M., Ahmad Khusyairi, A.R., Nur Khairunnisya, H., Siti Nurbalqis, M., “Oven Ageing versus UV Ageing Properties of Natural Rubber Cup Lump/EPDM Rubber Blend with Mangosteen Powder (MPP) as Natural Antioxidant”, IOP Conference Series: Materials Science and Engineering, 548, (2019).CrossRefGoogle Scholar
Bencherif, Y.A., Mekhaldi, A., Lobry, J., Olivier, M., Poorteman, M., “Molecular Macroscopic Characterization of EPDM’s Aging Used for Outdoor High Voltage Insulators”, Proceedings of 2018 3rd International Conference on Electrical Sciences and Technologies in Maghreb, CISTEM, (2019).Google Scholar
Redline, E.M., et al, “Anomalous aging of EPDM and FEPM under combined thermo-oxidative and hydrolytic conditions”, Polymer Degradation and Stability, 146, pp. 317-326 (2017).CrossRefGoogle Scholar
Pourmand, P., Hedenqvist, M.S., Furó, I., Gedde, U.W., “Deterioration of highly filled EPDM rubber by thermal ageing in air: Kinetics and non-destructive monitoring”, Polymer Testing, 66, pp. 267-276 (2017).CrossRefGoogle Scholar
Nykvist, B, Nilsson, M, “Rapidly falling costs of battery packs for electric? vehicles”, Nature Climate Change, 05, pp. 329-332 (2015).Google Scholar
Cooper, A, Furakawa, J, Lam, L, Kellaway, M., “The UltraBattery—A new battery design for a new beginning in hybrid electric vehicle energy storage”, Journal of Power Sources, 188, pp. 642-649 (2009).CrossRefGoogle Scholar
Scanlan, J, Watson, W F, “The interpretation of stress-relaxation measurements made on rubber during ageing”, Transactions of the Faraday Society, 54, pp. 740-750 (1958).CrossRefGoogle Scholar
Gates, T S, Veazie, D R, Brinson, L C, “Creep and Physical Aging in a Polymeric Composite: Comparison of Tension and Compression”, Journal of Composite Materials, 31, pp. 2478-2505 (1997).CrossRefGoogle Scholar
Ohki, Y, Hanada, S, Miyamoto, M, Hirai, N., Yang, L., “Aging mechanism of silicone rubber by heat and gamma-rays”, Conference on Electrical Insulation and Dielectric Phenomena. IEEE, pp. 869-872 (2016).Google Scholar
Patel, M, et al, “Complexities associated with moisture in foamed polysiloxane composites”, Polymer Degradation and Stability, 93, pp. 513-519 (2008).CrossRefGoogle Scholar
Kottner, R, Hynek, R, Mandys, T, Bartošek, J., “Material property determination of the lining layers of a versatile helmet”, MATEC Web of Conferences, 157, (2018).Google Scholar
Saotome, K, Matsurbara, K, Yatomi, T, “The Improvement of Humidity Resistance in High Resilient Polyurethane Foam”, Journal of Cellular Plastics, 13, pp. 203-209 (1977).CrossRefGoogle Scholar
Chang, H, et al, “Temperature and humidity effect on aging of silicone rubbers as sealing materials for proton exchange membrane fuel cell applications”, Applied Thermal Engineering, 104, pp. 472-478 (2016).CrossRefGoogle Scholar
Wu, J, Dong, J, Wang, Y, Gond, B.K., “Thermal oxidation ageing effects on silicone rubber sealing performance”, Polymer Degradation and Stability, 135, pp. 43-53 (2017).CrossRefGoogle Scholar
Zamfirova, G, Cherneva, S, Gaydarov, V, Vladkova, T., “Influence of Crosslinking on Micromechanical Characteristics of Liquid Silicone rubber. Numerical Simulations of Microindentation Process”, Bulgarian Chemical Communications, 47, pp. 433-441 (2015).Google Scholar
Belforte, G, Manuello, A, Mazza, L, “Optimization of the Cross Section of an Elastomeric Seal for Pneumatic Cylinders”, Journal of Tribology, 128, pp. 406-413 (2006).CrossRefGoogle Scholar
Song, G X, Wang, L, Park, Y C, “Analysis and optimization of nitrile butadiene rubber sealing mechanism of ball valve”, Transactions of Nonferrous Metals Society of China, 19, pp. 220-224 (2009).CrossRefGoogle Scholar
Sui, P C, Anderle, S, “Optimization of contact pressure profile for performance improvement of a rotary elastomeric seal operating in abrasive drilling environment”, Wear, 271, pp. 2466-2470 (2011).CrossRefGoogle Scholar
Lesinigo, M, Carlo, D’Angelo, Quarteroni, A, “A multiscale Darcy–Brinkman model for fluid flow in fractured porous media”, Numerische Mathematic, 117, pp. 717-752 (2011).CrossRefGoogle Scholar
Bottiglione, F, Carbone, G, Mantriota, G, “Fluid leakage in seals: An approach based on percolation theory”, Tribology International, 42, pp. 731-737 (2009).CrossRefGoogle Scholar
Lo, S-W, “A Study on Flow Phenomena in Mixed Lubrication Regime by Porous Medium Model”, Journal of Tribology, 116, pp. 640-647 (1994).CrossRefGoogle Scholar
Oliveira-Salmazo, L, Lopez-Gil, A, Silva-Bellucci, F, Job, A.E., Rodriguez-Perez, M.A., “Natural rubber foams with anisotropic cellular structures: Mechanical properties and modeling”, Industrial Crops and Products, 80, pp. 26-35 (2016).CrossRefGoogle Scholar
Hamilton, A R, et al, “Evaluation of the anisotropic mechanical properties of reinforced polyurethane foams”, Composites Science and Technology, 87, pp. 210-217 (2013).CrossRefGoogle Scholar
Gisi, S L D, Neet, T E, “Predicting the compressive properties of rigid urethane foam”, Journal of Applied Polymer Science, 20, pp. 2011-2029 (2010).CrossRefGoogle Scholar
Daghigh, V, Lacy, T E, Pittman, C U, Daghigh, H., “Influence of maleated polypropylene coupling agent on mechanical and thermal behavior of latania fiber-reinforced PP/EPDM composites”, Polymer Composites, 39, pp. 1751-1759 (2018).CrossRefGoogle Scholar
Vallet, C, Lasseux, D, Sainsot, P, Zahouani, H., “Real versus synthesized fractal surfaces: Contact mechanics and transport properties”, Tribology International, 42, pp. 250-259 (2009).CrossRefGoogle Scholar
Etsion, I, Front, I, “A Model for Static Sealing Performance of End Face Seals”, Tribology Transactions, 37, pp. 111-119 (1994).CrossRefGoogle Scholar
Zhang, M., Suo, S., Jiang, Y., Meng, G., “Experimental Measurement Method for Contact Stress of Elastic Metal Sealing Ring Based on Pressure Sensitive Paper”, Metals, 08, pp. 942 (2018).CrossRefGoogle Scholar
Xin, L, Gaoliang, P, “Research on leakage prediction calculation method for static seal ring in underground equipments”, Journal of Mechanical Science and Technology, 30, pp. 2635-2641 (2016).Google Scholar
Xiang, C, Guo, F, Jia, X, Wang, Y., Huang, X., “Thermo-elastohydrodynamic mixed-lubrication model for reciprocating rod seals”, Tribology International, 140, (2019).CrossRefGoogle Scholar
Xiang, C, et al, “Numerical algorithm for fluid-solid coupling in reciprocating rod seals”, Tribology International, 143, (2020).CrossRefGoogle Scholar
Guo, F., Jia, X., Suo, S., Salant, R.F., Wang, Y., “A mixed lubrication model of a rotary lip seal using flow factors”, Tribology International, 57, pp. 195–201 (2013).Google Scholar
Teale, J L, Lebeck, A O, “An Evaluation of the Average Flow Model [1] for Surface Roughness Effects in Lubrication”, Journal of Lubrication Technology, 102, pp. 360-366 (1980).CrossRefGoogle Scholar
Tripp, J H, “Surface Roughness in Effects in Hydrodynamic Lubrication: The Flow Factor Method”, Journal of Lubrication Technology, 105, pp. 458-463 (1983).CrossRefGoogle Scholar