Hostname: page-component-cd9895bd7-gxg78 Total loading time: 0 Render date: 2024-12-25T06:01:25.207Z Has data issue: false hasContentIssue false
  • English
  • Français

Comparison of Fatigue Tensile Properties of Scrimp-Gfrp and Hlup-Gfrp

Published online by Cambridge University Press:  05 May 2011

H.-J. Lin  and
C.-I Liao
H.-J. Lin*
Affiliation:
Dept. of Engineering Science and Ocean Engineering, National Taiwan University, Taipei, Taiwan 10617, R.O.C. Department of Electrical Engineering, National Panghu University, Penghu, Taiwan 88046, R.O.C.
C.-I Liao*
Affiliation:
Department of Engineering Science and Ocean Engineering, National Taiwan University, Taipei, Taiwan 10617, R.O.C.
*
*Professor
**Ph.D.
Get access

Abstract

Seemann Composites Resin Infusion Molding Process (called SCRIMPTM for short) is a resin transfer molding process which is commonly used in the manufacture of yachts. Fiber-Reinforced Plastic (called FRP for short) manufactured by using SCRIMP has higher fiber-volume-content than that manufactured by using Hand Lay-Up Process (called HLUP for short). In general, the tensile strength and fatigue strength are used to compare the tensile properties of SCRIMP-FRP and HLUP-FRP. In this paper, another viewpoint of comparison is used to compare their tensile properties, especially their fatigue tensile properties. Experiments on the fatigue life and damage phenomena in SCRIMP-FRP and HLUP-FRP were performed. Experimental results show that if the same fibers are used in SCRIMP-FRP and HLUPFRP, SCRIMP-FRP will be much thinner than HLUP-FRP and few air bubbles exist inside SCRIMP-FRP. Although SCRIMP-FRP has higher tensile strength than HLU-FRP, the tensile forces they can bear are approached. That means, processes do not affect the tensile load carrying capacities of FRP. However, SCRIMP-FRP exhibits shorter fatigue life than HLUP-FRP. The reason for that is discussed in this paper and qualitative analysis is performed to explain the author's contentions.

Keywords

FRPFatigueSCRIMP.
Type
Articles
Information
Journal of Mechanics , Volume 24 , Issue 3 , September 2008 , pp. 215 - 222
Copyright
Copyright © The Society of Theoretical and Applied Mechanics, R.O.C. 2008

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1.Abd Allah, M. H., Abdin, E. M., Selmy, A. I. and Khashaba, U. A., “Effect of Fiber Volume Fraction on the Fatigue Behavior of GRP Pultruded Rod Composites,” Composites Science and Technology, 56, pp. 23–29 (1996).CrossRefGoogle Scholar
2.Williams, C. D., Grove, S. M. and Summerscales, J., “The Compression Response of Fiber-Reinforced Plastic Plate During Manufacture by the Resin Infusion Under Flexible Tooling Method,” Composites Part A, 29, pp. 111–114(1998).CrossRefGoogle Scholar
3.Ferreira, J. A. M., Costa, J. D. M., Reis, P. N. B. and Richardson, M. O. W., “Analysis of Fatigue and Damage in Glass-Fibre-Reinforced Polypropylene Composite Materials,” Composites Science and Technology, 59, pp. 1461–1467 (1999).CrossRefGoogle Scholar
4.Mandell, J. F. and Samborsky, D. D., “Effects of Materials Parameters and Design Details on the Fatigue of Composite Materials for Wind Turbine Blades,” EWEC, Nice, France, pp. 1–5 (1999).Google Scholar
5.Liou, K. J., “Study on the Fatigue of Bolted Joints in Composite Materials: The Effects of Various Joint Geometry Parameters,” Master Thesis, Department of Engineering Science and Ocean Engineering, National Taiwan University (in Chinese) (2003).Google Scholar
6.Aidoo, J., Harries, K. A. and Petrou, M. F., “Fatigue Behavior of Carbon Fiber Reinforced Polymer- Strengthened Reinforced Concrete Bridge Girders,” Journal of Composites for Construction, 8, pp. 501–509 (2004).CrossRefGoogle Scholar
7.Natarajan, V., GangaRao, H. V. S. and Shekar, V., “Fatigue Response of Fabric-Reinforced Polymeric Composites,” Journal of Composite Materials, 39, pp. 1541–1559 (2005).CrossRefGoogle Scholar
8.Harries, K. A. and Aidoo, J., “Debonding- and Fatigue-Related Strain Limits for Externally Bonded FRP,” Journal of Composites for Construction, 10, pp. 87–90 (2006).CrossRefGoogle Scholar
9.Setiadi, Y., Jar, P.-Y. B., Kuboki, T. and Chenq, J.-J. R., “Comparison of Damage Development in Random Fiber-Reinforced Polymers (FRPS) Under Cyclic Loading,” Journal of Composite Materials, 40, pp. 71–91 (2006).CrossRefGoogle Scholar
10.Ni, J., Li, S. and Lee, L. J., “Analysis of Vacuum Infusion Resin Transfer Molding with Resin Distribution System,” Annual Technical Conference – ANTEC, Conference Proceedings,2, pp. 2406–2410 (1997).Google Scholar
11.Yang, H. and Lee, L. J., “Cure of Polyester and Vinylester Resins in SCRIMP,” International SAMPE Technical Conference, 31, pp. 487–498 (1999).Google Scholar
12.Shih, C. H., Liu, Q. F. and Lee, L. J., “Tackified SCRIMP for Aerospace Applications,” International SAMPE Symposium and Exhibition (Proceedings), 45, pp. 776–787 (2000).Google Scholar
13.Han, K., Jiang, S., Zhang, C. and Wang, B., “Flow Modeling and Simulation of SCRIMP for Composites Manufacturing,” Composites, Part A, 31, pp. 79–86 (2000).CrossRefGoogle Scholar
14.Liou, G. H., “Study on Fatigue Strength of SCRIMP and HLU Specimens,” Master Thesis, Department of Engineering Science and Ocean Engineering, National Taiwan University (in Chinese) (2003).Google Scholar
15.Stoven, T., Weyrauch, F., Mitschang, P. and Neitzel, M., “Continuous Monitoring of Three-Dimensional Resin Flow Through a Fibre Perform,” Composites, Part A, Applied Science and Manufacturing, 34, pp. 475–480 (2003).CrossRefGoogle Scholar
16.Boh, J. W., Louca, L. A., Choo, Y. S. and Mouring, S. E., “Damage Modelling of SCRIMP Woven Roving Laminated Beams Subjected to Transverse Shear,” Composites, Part B, Engineering, 36, pp. 427–438 (2005).CrossRefGoogle Scholar