Hostname: page-component-78c5997874-s2hrs Total loading time: 0 Render date: 2024-11-02T14:37:09.206Z Has data issue: false hasContentIssue false

Rapid cycle-dependent softening of equal channel angularly pressed Sn–Ag–Cu alloy

Published online by Cambridge University Press:  31 January 2011

Q.S. Zhu
Affiliation:
Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016, China
Z.G. Wang
Affiliation:
Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016, China
Q.L. Zeng
Affiliation:
Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016, China
S.D. Wu
Affiliation:
Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016, China
J.K. Shang*
Affiliation:
Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016, China; and Department of Materials Science and Engineering, University of Illinois at Urbana—Champaign, Urbana, Illinois 61801
*
a)Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

Cyclic stress–strain response of an equal channel angularly pressed Sn-3.8Ag-0.7Cu alloy was investigated to seek a mechanistic understanding of cyclic softening in Sn-rich alloys. The equal channel angular pressing (ECAP) was applied to modify the microstructure of the solder alloy by breaking up the needlelike Ag3Sn intermetallic phase into fine granules and by reducing the large β-Sn dendrites into smaller and equiaxed grains. The extruded alloys were subjected to strain-controlled fatigue test at various strain amplitudes. It was found that the extruded alloy exhibited a sharp decrease of the stress amplitude within the initial few cycles compared with the as-cast alloy. After only a few cycles, the alloy suffered from noticeable surface damage. In situ scanning electron microscopy observations of the cyclic bending specimens revealed an approximately logarithmic relationship between crack density and the number of cycles. A theoretical model of microcrack accumulation was constructed to explain the rapid cyclic softening behavior. The predicted results, based on the model, agreed well with the experimental data and indicated that the rapid softening had resulted from an increased tendency for grain boundary cracking in the ECAPed microstructure due to the increase in the grain boundary area per unit volume and the reduced resistance of Ag3Sn to grain boundary sliding.

Keywords

Type
Articles
Copyright
Copyright © Materials Research Society 2008

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1Abtew, M., Selvaduray, G.: Lead-free solders in microelectronics. Mater. Sci. Eng., R 27, 95 2000Google Scholar
2Zeng, K., Tu, K.N.: Six cases of reliability study of Pb-free solder joints in electronic packaging technology. Mater. Sci. Eng., R 38, 55 2002CrossRefGoogle Scholar
3Salam, B., Ekere, N.N., Rajkumar, D.: 2001 Electronic Components and Technology Conference IEEE Piscataway, NJ 2001 471Google Scholar
4Glazer, J.: Metallurgy of low-temperature Pb-free solders for electronic assembly. Int. Mater. Rev. 40, 65 1995CrossRefGoogle Scholar
5Plumbridge, W.J.: Solders in electronics. J. Mater. Sci. 31, 2501 1996CrossRefGoogle Scholar
6Chio, S., Subramanian, K.N., Lucas, J.P., Bieler, T.R.: Thermomechanical fatigue behavior of Sn–Ag solder joints. J. Electron. Mater. 29, 1249 2000Google Scholar
7Kanchanomai, C., Miyashita, Y., Mutoh, Y.: Low-cycle fatigue behavior of Sn–Ag, Sn–Ag–Cu, and Sn–Ag–Cu–Bi lead-free solders. J. Electron. Mater. 31, 456 2002Google Scholar
8Kanchanomai, C., Yamamoto, S., Miyashita, Y., Mutoh, Y., McEvily, A.J.: Low cycle fatigue test for solders using non-contact digital image measurement system. Int. J. Fatigue 24, 57 2002CrossRefGoogle Scholar
9Pang, J.H.L., Xiong, B.S., Low, T.H.: Low cycle fatigue study of lead free 99.3Sn-0.7Cu solder alloy. Int. J. Fatigue 26, 865 2004CrossRefGoogle Scholar
10Zeng, Q.L., Wang, Z.G., Xian, A.P., Shang, J.K.: Cyclic softening of the Sn-3.8Ag-0.7Cu lead-free solder alloy with equiaxed grain structure. J. Electron. Mater. 34, 62 2005CrossRefGoogle Scholar
11Shang, J.K., Zeng, Q.L., Zhang, L., Zhu, Q.S.: Mechanical fatigue of Sn-rich Pb-free solder alloys. J. Mater. Sci. 18, 211 2007Google Scholar
12Liang, J., Gollhardt, N., Lee, P.S., Schroeder, S.A., Morris, W.L.: A study of fatigue and creep behavior of four high temperature solders. Fatigue Fract. Eng. Mater. Struct. 19, 1401 1996CrossRefGoogle Scholar
13Segal, V.M.: Materials processing by simple shear. Mater. Sci. Eng., A 197, 157 1995CrossRefGoogle Scholar
14Valiev, R.Z., Islamgaliev, R.K., Alexandrov, I.V.: Bulk nanostructured materials from severe plastic deformation. Prog. Mater. Sci. 45, 103 2000Google Scholar
15Tsuji, N., Saito, Y., Utsunomiya, H., Tanigawa, S.: Ultra-fine grained bulk steel produced by accumulative roll-bonding (ARB) process. Scr. Mater. 40, 795 1999CrossRefGoogle Scholar
16Zhu, Y.T., Koloboy, Y.R., Graboyetskaya, G.P., Stolyarov, V.V., Girsova, N.V., Valiev, R.Z.: Microstructures and mechanical properties of ultrafine-grained Ti foil processed by equal-channel angular pressing and cold rolling. J. Mater. Res. 18, 1011 2003CrossRefGoogle Scholar
17Ochoa, F., Williams, J.J., Chawla, N.: Effects of cooling rate on the microstructure and tensile behavior of a Sn-3.5wt%Ag solder. J. Electron. Mater. 32, 1414 2003Google Scholar
18Murayama, M., Horita, Z., Hono, K.: Microstructure of two-phase Al–1.7 at.% Cu alloy deformed by equal-channel angular pressing. Acta Mater. 49, 21 2001Google Scholar
19Vinogradov, A., Patlan, V., Suzuki, Y., Kitagawa, K., Kopylov, V.I.: Structure and properties of ultra-fine grain Cu–Cr–Zr alloy produced by equal-channel angular pressing. Acta Mater. 50, 1639 2002Google Scholar
20Kim, H.K., Choi, M.I., Chung, C.S., Shin, D.H.: Fatigue properties of ultrafine grained low carbon steel produced by equal channel angular pressing. Mater. Sci. Eng., A 340, 243 2003CrossRefGoogle Scholar
21Zhu, Q.S., Zhang, L., Wang, Z.G., Wu, S.D., Shang, J.K.: Effect of intermetallics Ag3Sn on the tensile property of Sn3.8Ag0.7Cu solder alloy. Acta Metall. Sinica 43(1), 41 2007Google Scholar
22Feltner, C.E., Laird, C.: Cyclic stress-strain response of F.C.C. metals and alloys: Dislocation structure and mechanisms. Acta Metall. 15, 1633 1967CrossRefGoogle Scholar
23Agnew, S.R., Weertman, J.R.: Cyclic softening of ultrafine grain copper. Mater. Sci. Eng., A 244, 145 1998Google Scholar
24Fine, M.E.: Fatigue resistance of metals. Metall. Trans. A 11, 365 1980Google Scholar
25Stolkarts, V., Keer, L.M., Fine, M.E.: Demage evolution governed by microcrack nucleation with application to the fatigue of 63Sn-37Pb solder. J. Mech. Phys. Solids 47, 2451 1999CrossRefGoogle Scholar
26Kachanov, L.M.: Introduction to Continuum Damage Mechanics Kluwers Academic Publishers Boston, MA 1986Google Scholar
27Budiansky, B., O’Connel, R.J.: Elastic moduli of a cracked solid. Int. J. Solids Struct. 12, 81 1976CrossRefGoogle Scholar
28Subramanian, K.N., Lee, J.G.: Effect of anisotropy of tin on thermomechanical behavior of solder joints. J. Mater. Sci.-Mater. Electron. 15, 235 2004Google Scholar
29Henderson, D.W., Woods, J.J., Gosselin, T.A., Bartelo, J., King, D.E., Korhonen, T.M., Korhonen, M.A., Lehman, L.P., Cotts, E.J., Kang, S.K., Lauro, P., Shih, D.Y., Goldsmith, C., Puttlitz, K.J.: The microstructure of Sn in near-eutectic Sn–Ag–Cu alloy solder joints and its role in thermomechanical fatigue. J. Mater. Res. 19, 1608 2004CrossRefGoogle Scholar
30Lee, J.G., Telang, A., Subramanian, K.N., Bieler, T.R.: Modeling thermomechanical fatigue behavior of Sn–Ag solder joints. J. Electron. Mater. 31, 1152 2002CrossRefGoogle Scholar
31Matin, M.A., Coenen, E.W.C., Vellinga, W.P., Geers, M.G.D.: Correlation between thermal fatigue and thermal anisotropy in a Pb-free solder alloy. Scr. Mater. 53, 927 2005Google Scholar