Hostname: page-component-78c5997874-dh8gc Total loading time: 0 Render date: 2024-11-08T01:24:23.499Z Has data issue: false hasContentIssue false
  • English
  • Français

Processing of diamond/alumina composites for low wear applications

Published online by Cambridge University Press:  31 January 2011

May-Ying Chu ,
Bharat Bhushan  and
Lutgard C. De Jonghe
May-Ying Chu*
Affiliation:
Department of Materials Science and Mineral Engineering, University of California, Berkeley, California 94720
Bharat Bhushan*
Affiliation:
IBM Research Division, Almaden Research Center, San Jose, California 95120
Lutgard C. De Jonghe
Affiliation:
Department of Materials Science and Mineral Engineering, University of California, Berkeley, California 94720
*
a)Presently at PolyPlus Battery Company, Inc., 809 Bancroft Way, Berkeley, California 94710.
b)Presently at Computer Microtribology and Contamination Laboratory, Department of Mechanical Engineering, The Ohio State University, Columbus, Ohio 43210.
Get access

Abstract

A simple hot-pressing procedure for fabricating composites of diamond particulates in an alumina matrix at moderate applied pressures is described. Dense composites with up to 33 vol. % diamond particles are made by pressure-sintering at applied stress of 35 MPa in vacuum atmosphere. Preliminary wear tests of these composites on magnetic thin-film rigid disks show a low friction comparable to that of single crystalline diamond. Diamond/alumina composites can be an economical alternative to diamond or diamond coated materials for abrasion resistant applications.

Type
Articles
Information
Journal of Materials Research , Volume 7 , Issue 11 , November 1992 , pp. 3010 - 3018
Copyright
Copyright © Materials Research Society 1992

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1Bhushan, B., Tribology and Mechanics of Magnetic Storage Devices (Springer-Verlag, New York, 1990).CrossRefGoogle Scholar
2Chandrasekar, S. and Bhushan, B., J. Trib., Trans. ASME 112, 1–16 (1990).Google Scholar
3Chandrasekar, S. and Bhushan, B., J. Trib., Trans. ASME 113, 313–317 (1991).CrossRefGoogle Scholar
4Backmann, K. P. and Messier, R., Chem. and Eng. News 67 (20), 1–58 (1989).Google Scholar
5Spear, K.E., J. Am. Ceram. Soc. 72 (2), 171–191 (1989).CrossRefGoogle Scholar
6Bhushan, B. and Gupta, B. K., Handbook of Tribology: Materials, Coatings and Surface Treatments (McGraw-Hill, New York, 1991).Google Scholar
7Cho, N-H., Krishnan, K.M., Veirs, D.K., Rubin, M.D., Hopper, C.B., Bhushan, B., and Bogy, D.B., J. Mater. Res. 5, 2543–2554 (1990).CrossRefGoogle Scholar
8Noma, T. and Sawaoka, A., J. Mater. Sci. 19 (7), 2319–2322, (1984).CrossRefGoogle Scholar
9Noma, T. and Sawaoka, A., J. Am. Ceram. Soc. 68 (2), C36–C37 (1985).Google Scholar
10Noma, T. and Sawaoka, A., J. Am. Ceram. Soc. 68 (10), C271–C273 (1985).Google Scholar
11Jorgensen, P. J., J. Am. Ceram. Soc. 48 (4), 207–210 (1965).CrossRefGoogle Scholar
12Smothers, W. J. and Reynolds, H. J., J. Am. Ceram. Soc. 37 (12), P588–595 (1954).CrossRefGoogle Scholar
13Chu, M-Y., Bhushan, B., and Jonghe, L.C. De, Tribology and Mechanics of Magnetic Storage Systems, STLE Special Publication SP–29, 7, 9–16 (1990).Google Scholar
14Jonghe, L. C. De and Rahaman, M. N., in Processing Science of Advanced Ceramics, edited by Aksay, L.A., McVay, G.L., and Ulrich, D. R. (Mater. Res. Soc. Symp. Proc. 155, Pittsburgh, PA, 1989), pp. 353–361.Google Scholar
15Weiser, M.W. and Jonghe, L.C. De, J. Am. Ceram. Soc. 71 (3), C–125 (1988).CrossRefGoogle Scholar
16Lange, F.F., J. Mater. Res. 2, 59–65 (1987).CrossRefGoogle Scholar
17Kapolnek, D. and Jonghe, L. C. De, J. European Ceram. Soc. 7, 345–351 (1991).CrossRefGoogle Scholar