Hostname: page-component-586b7cd67f-2brh9 Total loading time: 0 Render date: 2024-11-28T11:22:08.876Z Has data issue: false hasContentIssue false
  • English
  • Français

Numerical investigation of indentation fatigue on polycrystalline copper

Published online by Cambridge University Press:  31 January 2011

B.X. Xu ,
Z.F. Yue  and
X. Chen
B.X. Xu*
Affiliation:
School of Mechanics, Civil Engineering and Architecture, Northwestern Polytechnical University, Xi’an 710072, Peoples Republic of China; and Columbia Nanomechanics Research Center, Department of Civil Engineering and Engineering Mechanics, Columbia University, New York, New York 10027-6699
Z.F. Yue
Affiliation:
School of Mechanics, Civil Engineering and Architecture, Northwestern Polytechnical University, Xi’an 710072, Peoples Republic of China
X. Chen
Affiliation:
Columbia Nanomechanics Research Center, Department of Civil Engineering and Engineering Mechanics, Columbia University, New York, New York 10027-6699
*
a) Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

The dynamic indentation response of polycrystalline copper under cyclic fatigue loading is studied with a flat cylindrical indenter. First, a simple analytical model shows that in a purely elastic solid, the indentation depth responds with the same wavelength and frequency as the applied sinusoidal fatigue load. Next, a numerical simulation of an indentation fatigue test on an elastic-plastic solid (polycrystalline copper) is performed. Finite element analyses reveal that the mean indentation depth is controlled by both the mean of the indentation fatigue load and the load amplitude, while the amplitude of the indentation depth is independent of the mean load. Further investigations indicate that with an increased number of cycles, the increment of indentation depth reaches a constant rate. The steady state indentation depth rate is dependent not only on the amplitude of indentation fatigue load but also on the fatigue mean load, which is similar to strain accumulation during a conventional fatigue test. A parallel indentation experiment on annealed polycrystalline copper also confirms the effect of the fatigue mean load, indicating consistency with numerical results.

Keywords

FatigueMetal
Type
Articles
Information
Journal of Materials Research , Volume 24 , Issue 3 , March 2009 , pp. 1007 - 1015
Copyright
Copyright © Materials Research Society 2009

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Oliver, W.C. and Pharr, G.M.: Measurement of hardness and elastic modulus by instrumented indentation: Advances in understanding and refinements to methodology., J. Mater. Res. 19, 3 (2004).Google Scholar
2.Cheng, Y.T. and Cheng, C.M.: Scaling dimensional analysis and indentation measurements. Mater. Sci. Eng., R 44, 91 (2004).Google Scholar
3.Chen, X., Ogasawara, N., Zhao, M., and Chiba, N.: On the uniqueness of measuring elastoplastic properties from indentation: The indistinguishable mystical materials., J. Mech. Phys. Solids 55, 1618 (2007).Google Scholar
4.Xia, Z.H., Curtin, W.A., and Sheldon, B.W.: A new method to evaluate the fracture toughness of thin films. Acta Mater. 52, 3507 (2004).CrossRefGoogle Scholar
5.Chen, X., Xiang, Y., and Vlassak, J.J.: A novel technique to measure mechanical properties of porous materials by nanoindentation. J. Mater. Res. 21, 715 (2006).Google Scholar
6.Mason, J.K., Lund, A.C., and CSchuh, A.: Determining the activation energy and volume for the onset of plasticity during nanoindentation. Phys. Rev. B 73, 054102 (2006).CrossRefGoogle Scholar
7.Gouldstone, A., Chollacoop, N., Dao, M., Li, J., Minor, A.M., and Shen, Y.L.: Indentation across size scales and disciplines: Recent developments in experimentation and modeling. Acta Mater. 55, 4015 (2007).CrossRefGoogle Scholar
8.Zhao, M.H., Chen, X., Yan, J., and Karlsson, A.M.: Determination of uniaxial residual stress and mechanical properties by instrumented indentation. Acta Mater. 54, 2823 (2006).Google Scholar
9.Pane, I. and Blank, E.: Role of plasticity on indentation behavior: Relations between surface and subsurface responses. Int. J. Solids Struct. 43, 2014 (2006).Google Scholar
10.Li, X.D. and Bhushan, B.: A review of nanoindentation continuous stiffness measurement technique and its applications. Mater. Charact. 48, 11 (2002).Google Scholar
11.Fischer-Cripps, A.C.: Multiple-frequency dynamic nanoindentation testing. J. Mater. Res. 19, 2981 (2004).CrossRefGoogle Scholar
12.Ossa, E.A., Deshpande, V.S., and Cebon, D.: Spherical indentation behaviour of bitumen. Acta Mater. 53, 3103 (2005).Google Scholar
13.Saraswati, T., Sritharan, T., Mhaisalkar, S., CBreach, D., and Wulf, F.: Cyclic loading as an extended nanoindentation technique. Mater. Sci. Eng., A 423, 14 (2006).Google Scholar
14.VanVliet, K.J. and Suresh, S.: Simulations of cyclic normal indentation of crystal surfaces using the bubble-raft model. Philos. Mag. A 82, 1993 (2002).Google Scholar
15.Shiari, B. and Miller, R.E.: Multiscale modeling of ductile crystals at the nanoscale subjected to cyclic indentation. Acta Mater. 56, 2799 (2008).Google Scholar
16.Cairney, J.M., Tsukano, R., Hoffman, M.J., and Yang, M.: Degradation of TiN coatings under cyclic loading. Acta Mater. 52, 3229 (2004).CrossRefGoogle Scholar
17.Raju, T.D., Nakasa, K., and Kato, M.: Relation between delamination of thin films and backward deviation of load–displacement curves under repeating nanoindentation. Acta Mater. 51, 457 (2003).CrossRefGoogle Scholar
18.Cheng, Y.T., Ni, W.Y., and Cheng, C.M.: Nonlinear analysis of oscillatory indentation in elastic and viscoelastic solids. Phys. Rev. Lett. 97, 075506 (2006).Google Scholar
19.Mencik, J., Rauchs, G., Bardon, J., and Riche, A.: Determination of elastic modulus and hardness of viscoelastic-plastic materials by instrumented indentation under harmonic load. J. Mater. Res. 20, 2660 (2005).CrossRefGoogle Scholar
20.Odegard, G.M., Gates, T.S., and Herring, H.M.: Characterization of viscoelastic properties of polymeric materials through nanoindentation. Exp. Mech. 45, 2005130 (2005).Google Scholar
21.VanLandingham, M.R., Chang, N.K., Drzal, P.L., White, C.C., and Chang, S.H.: Viscoelastic characterization of polymers using instrumented indentation. I. Quasi-static testing. J. Polym. Sci., Part B: Polym. Phys. 43, 1794 (2005).Google Scholar
22.Li, J.C.M. and Chu, S.N.G.: Impression fatigue. Scr. Mater. 13, 1021 (1979).Google Scholar
23.Xu, B.X. and Yue, Z.F.: A study of the ratcheting by the indentation fatigue method with a flat cylindrical indenter: Part I. Experimental study., J. Mater. Res. 21, 1793 (2006).Google Scholar
24.Xu, B.X. and Yue, Z.F.: A study of the ratcheting by the indentation fatigue method with a flat cylindrical indenter: Part II. Finite element simulation. J. Mater. Res. 22, 186 (2007).CrossRefGoogle Scholar
25.Sneddon, I.N.: The relation between load and penetration in the axisymmetric Boussinesq problem for a punch of arbitrary profile. Int. J. Eng. Sci. 3, 47 (1965).CrossRefGoogle Scholar
26.ABAQUS User's Manual, Version 6.2 (Hibbitt, Karlsson and Sor-ensen, Inc., Pawtucket, RI, 2001).Google Scholar
27.Chaboche, J.L. and Nouaihas, D.: Constitutive modelling of ratchetting effects—Part I: Experimental facts and properties of the classical models. J. Eng. Mater. Technol. 111, 384 (1989).CrossRefGoogle Scholar
28.Chaboche, J.L. and Nouaihas, D.: Constitutive modelling of ratchetting effects—Part II: Possibilities of some additional kinematic rules., J. Eng. Mater. Technol. 111, 409 (1989).Google Scholar
29.Ohno, N. and Wang, J.D.: On modelling of kinematic hardening for retcheting behaviour. Nucl. Eng. Des. 153, 205 (1995).Google Scholar
30.Delobelle, P., Robinet, P., and Bocher, L.: Experimental study and phenomenological modelization of ratchet under uniaxial and biaxial loading on an austenitic stainless steel. Int. J. Plast. 11, 295 (1995).Google Scholar
31.Jiang, Y. and Kurath, P.: Characteristics of the Armstrong-Frederick type plasticity models. Int. J. Plast. 12, 387 (1996).Google Scholar
32.Moosbrugger, J.C. and Morrison, D.J.: Nonlinear kinematic hardening rule parameters—Direct determination from completely reversed proportional cycling. Int. J. Plast. 13, 633 (1997).Google Scholar
33.Abdel-Karim, M. and Ohno, N.: Kinematic hardening model suitable for ratchetting with steady-state. Int. J. Plast. 16, 225 (2000).Google Scholar
34.Mclean, D.: Mechanical Properties of Metals (Wiley, New York, 1965), p. 112.Google Scholar
35.Yokouchi, Y., Greenfield, I.G., Chou, T.W., and Iturbe, E.B.: Elastic-plastic analysis of indentation damage: Cyclic loading of copper. J. Mater. Sci. 22, 3087 (1987).Google Scholar
36.Xu, B.X., Wang, X.M., and Yue, Z.F.: Indentation behavior of polycrystalline copper under fatigue peak overloading. J. Mater. Res. 22, 1585 (2007).Google Scholar
37.Xu, B.X., Yue, Z.F., and Wang, J.: Indentation fatigue behaviour of polycrystalline copper. Mech. Mater. 39, 1066 (2007).Google Scholar
38.Chandlera, H.D. and Kwofie, S.: A description of cyclic creep under conditions of axial cyclic and mean stresses. Int. J. Fatigue 27, 541 (2005).Google Scholar
39.Megahed, M., Ponter, A.R.S., and Morrison, C.J.: Experimental investigations into the influence of cyclic phenomena of metals on structural ratchetting behavior. Int. J. Mech. Sci. 26, 625 (1984).Google Scholar