Hostname: page-component-78c5997874-g7gxr Total loading time: 0 Render date: 2024-11-01T15:43:39.074Z Has data issue: false hasContentIssue false
  • English
  • Français

Microstructure evolution and microimpact performance of Sn–Ag–Cu solder joints under thermal cycle test

Published online by Cambridge University Press:  31 January 2011

Y.L. Huang ,
K.L. Lin  and
D.S. Liu
K.L. Lin
Affiliation:
Department of Materials Science and Engineering, National Cheng Kung University, Tainan, Taiwan 70101, Republic of China
D.S. Liu
Affiliation:
Department of Mechanical Engineering, National Chung Cheng University, Chia-Yi, Taiwan 62102, Republic of China
Get access

Abstract

The microstructure and microimpact performance of Sn1Ag0.1Cu0.02Ni0.05In (SAC101NiIn)/AuNi/Cu solder ball joints were investigated after a thermal cycle test (TCT). The joints show complete bulk fracture behavior before TCT. Moreover, TCT facilitated interfacial fracture behavior with lower fracture energy. The intermetallic compounds (IMCs) formed in the solder joints before and after TCT were investigated. TCT induces a variety of structural variations in the solder joints, including slipping bands, whisker formation, the squeezing of the IMC layer, the formation of cavities, the rotation and pop-up of grain, and the deformation and rotation of the entire joint. The variations in fracture behavior induced by TCT are correlated with the structural variations in the solder joints.

Keywords

FatigueMicrostructureFracture
Type
Articles
Information
Journal of Materials Research , Volume 25 , Issue 7 , July 2010 , pp. 1312 - 1320
Copyright
Copyright © Materials Research Society 2010

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Chawla, N.Thermomechanical behaviour of environmentally-benign Pb-free solders. Int. Mater. Rev. 54, 368 (2009)CrossRefGoogle Scholar
2.Liu, X., Lu, G.Q.Effect of solder joint shape and height on thermal fatigue lifetime. IEEE Trans. Compon. Packag. Technol. 26, 455 (2003)Google Scholar
3.Kinyanjui, R., Lehman, L.P., Zavalij, L., Cotts, E.Effect of sample size on the solidification temperature and microstructure of SnAgCu near eutectic alloys. J. Mater. Res. 20, 2914 (2005)CrossRefGoogle Scholar
4.Bieler, T.R., Jiang, H., Lehman, L.P., Kirkpatrick, T., Cotts, E.J., Nandagopal, B.Influence of Sn grain size and orientation on the thermomechanical response and reliability of Pb-free solder joints. IEEE Trans. Compon. Packag. Technol. 31, 370 (2008)CrossRefGoogle Scholar
5.Telang, A.U., Bieler, T.R., Choi, S., Subramanian, K.N.Orientation imaging studies of Sn-based electronic solder joints. J. Mater. Res. 17, 2294 (2002)CrossRefGoogle Scholar
6.Sidhu, R.S., Chawla, N.Microstructure characterization and creep behavior of Sn-rich solder alloys, Part I: Microstructure characterization. Metall. Mater. Trans. A 39, 340 (2008)CrossRefGoogle Scholar
7.Sidhu, R.S., Deng, X., Chawla, N.Microstructure characterization and creep behavior of Sn-rich solder alloys. Part II: Creep behavior. Metall. Mater. Trans. A 39, 349 (2008)CrossRefGoogle Scholar
8.Terashima, S., Tanaka, M., Tasumi, K.Thermal fatigue properties and grain boundary character distribution in Sn–xAg–0.5Cu (x = 1, 1.2, and 3) lead free solder interconnects. Sci. Technol. Weld. Joining 13, 60 (2008)CrossRefGoogle Scholar
9.Teo, J.W.R.Thermal cycling aging effect on the reliability and morphological evolution of SnAgCu solder joints. IEEE Trans. Compon. Packag. Technol. 30, 279 (2007)Google Scholar
10.Lai, Y.S., Chang, H.C., Yeh, C.L.Evaluation of solder joint strengths under ball impact test. Microelectron. Reliab. 47, 2179 (2007)CrossRefGoogle Scholar
11.Zhu, W.H., Xu, L., Pang, J.H.L., Zhang, X.R., Poh, E., Sun, Y.F., Sun, A.Y.S., Wang, C.K., Tan, H.B.Drop reliability study of PBGA assemblies with SAC305, SAC105 and SAC105-Ni solder ball on Cu-OSP and ENIG substrate finishProceedings of the 58th Electron. Comp. Tech. Conf. (Lake Buena Vista, FL 2008)1667Google Scholar
12.Wong, E.H., Selvanayagam, C.S., Seah, S.K.W., Driel, W.D., Caers, J.F.J.M., Zhao, X.J., Owens, N., Tan, L.C., Frear, D.R., Leoni, M., Lai, Y.S., Yeh, C.L.Stress-strain characteristics of tin-based solder alloys for drop-impact modeling. J. Electron. Mater. 37, 829 (2008)CrossRefGoogle Scholar
13.Ou, S.Q., Xu, Y.H., Tu, K.N.Micro-impact test on lead-free BGA balls on Au/electrolytic Ni/Cu bond padProceedings of the 55th Electron. Comp. Tech. Conf. (Reno, NV 2005)467Google Scholar
14.Deng, X., Koopman, M., Chawla, N., Chawla, K.K.Young's modulus of (Cu,Ag)–Sn intermetallics measured by nanoindentation. Mater. Sci. Eng., A 364, 240 (2004)CrossRefGoogle Scholar
15.Huang, Y.L., Lin, K.L., Liu, D.S.The micro-impact fracture behavior of lead-free solder ball joints. J. Mater. Res. 23, 1057 (2008)CrossRefGoogle Scholar
16.Huang, Y.L., Lin, K.L., Liu, D.S.Effect of impact rate on the strength of lead-free solder jointsProceedings of the 10th IEEE Electron. Pack. Tech. Conf. (Singapore 2008)1369Google Scholar
17.Lee, B.Z., Lee, D.N.Spontaneous growth mechanism of tin whiskers. Acta. Mater. 46, 3701 (1998)CrossRefGoogle Scholar
18.Sidhu, R.S., Chawla, N.Thermal fatigue behavior of Sn-rich (Pb-Free) solders. Metall. Mater. Trans. A 39, 799 (2008)CrossRefGoogle Scholar
19.Tai, L.J., Tsai, I., Wu, E.Mechanical properties of Ni3Sn4 and Cu3Sn determined by inverse method. IEEE Trans. Compon. Packag. Technol. 31, 503 (2008)Google Scholar
20.Nousiainen, O., Lehtiniemi, L., Kangasvieri, T., Rautioaho, R., Vahakangas, J.Thermal fatigue endurance of collapsible 95.5Sn4Ag0.5Cu spheres in LTCC/PWB assemblies. Microelectron. Reliab. 48, 622 (2008)CrossRefGoogle Scholar
21.Tsai, M.Y., Chang, H.Y., Pecht, M.Warpage analysis of flip-chip PBGA packages subject to thermal loading. IEEE Trans. Device Mater. Reliab. 9, 419 (2009)CrossRefGoogle Scholar
22.Tsai, M.Y., Hsu, C.H., Wang, C.T.Investigation of thermomechanical behaviors of flip chip BGA packages during manufacturing process and thermal cycling. IEEE Trans. Compon. Packag. Technol. 27, 568 (2004)CrossRefGoogle Scholar