Hostname: page-component-586b7cd67f-rdxmf Total loading time: 0 Render date: 2024-11-24T15:40:24.000Z Has data issue: false hasContentIssue false
  • English
  • Français

Microstructure and mechanical properties of the hot-rolled Mg–Y–Nd–Zr alloy

Published online by Cambridge University Press:  01 May 2013

Xiao Wang ,
Chuming Liu ,
Lu Xu ,
Hongchao Xiao  and
Liang Zheng
Xiao Wang
Affiliation:
Department of Materials Science and Engineering, Central South University, Changsha 410083, China
Chuming Liu*
Affiliation:
Department of Materials Science and Engineering, Central South University, Changsha 410083, China
Lu Xu
Affiliation:
Department of Materials Science and Engineering, Central South University, Changsha 410083, China
Hongchao Xiao
Affiliation:
Department of Materials Science and Engineering, Central South University, Changsha 410083, China
Liang Zheng
Affiliation:
Department of Materials Science and Engineering, Central South University, Changsha 410083, China
*
a)Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

Microstructures and mechanical properties of the Mg–4Y–2.5Nd–0.6Zr (wt%) alloy in the as-cast, as-rolled, and rolled-T5 conditions have been investigated. Results showed that the as-cast sample mainly consisted of the α-Mg matrix, network-like Mg41Nd5 phase, and cuboid-shaped Mg24Y5 particles. For the as-rolled sample, the thermally stable Mg24Y5 particles located at both grain boundaries and matrix, and the average grain size was greatly refined to about 15 μm. Yield strength, ultimate tensile strength, and elongation of as-rolled samples were 290 MPa, 235 MPa, and 10%, respectively. They were enhanced by 48.7%, 56.7%, and 38.9% correspondingly compared with those of the as-cast sample. After isothermal aging at 250 °C for 4 h, the optimal mechanical properties can be obtained. Besides, the tensile strengths of as-rolled and rolled-T5 samples decreased gradually with a gradual increase of ductility from room temperature to 300 °C. Quasicleavage and cleavage fracture were the fracture patterns of as-rolled and rolled-T5 samples, respectively, at room temperature. For samples under the two conditions, fracture mode similarly changed with the increase of test temperatures, and ductile fracture can be observed at higher temperature.

Type
Articles
Information
Journal of Materials Research , Volume 28 , Issue 10 , 28 May 2013 , pp. 1386 - 1393
Copyright
Copyright © Materials Research Society 2013 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

Rokhlin, L.L.: Magnesium Alloys Containing Rear Earth Metals (Taylor and Francis , London, 2003).CrossRefGoogle Scholar
Mordike, B.L. and Ebert, T.: Magnesium: Properties-applications-potential. Mater. Sci. Eng., A 302, 37 (2001).CrossRefGoogle Scholar
Li, W.P., Zhou, H., and Li, Z.F.: Effect of gadolinium on microstructure and rolling capability of AZ31 alloy. J. Alloys Compd. 475, 227 (2009).CrossRefGoogle Scholar
Lin, L., Chen, L.J., and Liu, Z.: Tensile strength improvement of an Mg-12Gd-3Y(wt%) alloy processed by hot extrusion and free forging. J. Mater. Sci. 43, 4493 (2008).CrossRefGoogle Scholar
Ding, W.J., Li, D.Q., Wang, Q.D., and Li, Q.: Microstructure and mechanical properties of hot-rolled Mg-Zn-Nd-Zr alloys. Mater. Sci. Eng., A 483–484, 228 (2008).CrossRefGoogle Scholar
Homma, T., Kunito, N., and Kamado, S.: Fabrication of extraordinary high-strength magnesium alloy by hot extrusion. Scr. Mater. 61, 644 (2009).CrossRefGoogle Scholar
Liu, K. and Meng, J.: Microstructures and mechanical properties of the extruded Mg-4Y-2Gd-xZn-0.4Zr alloys. J. Alloys Compd. 509, 3299 (2011).CrossRefGoogle Scholar
Zhang, J.H., Leng, Z., Liu, S.J., Li, J.Q., Zhang, M.L., and Wu, R.Z.: Microstructure and mechanical properties of Mg-Gd-Dy-Zn alloy with long period stacking ordered structure or stacking faults. J. Alloys Compd. 509, 7717 (2011).CrossRefGoogle Scholar
Nie, J.F. and Muddle, B.C.: Characterisation of strengthening precipitate phases in a Mg-Y-Nd alloy. Acta Mater. 48, 1691 (2000).CrossRefGoogle Scholar
Wu, A.R. and Xia, C.Q.: Study of the microstructure and mechanical properties of Mg-rare earth alloys. Mater. Des. 28, 1963 (2007).CrossRefGoogle Scholar
Wang, L.D., Xing, C.Y., Hou, X.L, Wu, Y.M., Sun, J.F., and Wang, L.M.: Microstructures and mechanical properties of as-cast Mg-5Y-3Nd-Zr-xGd (x=0, 2 and 4 wt.%) alloys. Mater. Sci. Eng., A 527, 1891 (2010).CrossRefGoogle Scholar
Antion, C., Donnadieu, P., Perrard, F., Deschamps, A., Tassin, C., and Pisch, A.: Hardening precipitation in a Mg-4Y-3RE alloy. Acta Mater. 51, 5335 (2003).CrossRefGoogle Scholar
Fu, P.H., Peng, L.M., Jiang, H.Y., Zhang, Z.Y., and Zhai, C.Q.: Fracture behavior and mechanical properties of Mg-4Y-2Nd-1Gd-0.4Zr(wt.%) alloy at room temperature. Mater. Sci. Eng., A 486, 572 (2008).Google Scholar
Mohri, T., Mabuchi, M., Satio, N., and Nakamura, M.: Microstructure and mechanical properties of a Mg-4Y-3RE alloy processed by thermo-mechanical treatment. Mater. Sci. Eng., A 257, 287 (1998).CrossRefGoogle Scholar
Fang, X.Y., Yi, D.Q., Nie, J.F., Zhang, X.J., Wang, B., and Xiao, L.R.: Effect of Zr, Mn and Sc additions on the grain size of Mg-Gd alloy. J. Alloys Compd. 470, 311 (2009).CrossRefGoogle Scholar
Xin, R.L., Li, L., Zeng, K., Song, B., and Liu, Q.: Structural examination of aging precipitation in a Mg-Y-Nd alloy at different temperatures. Mater. Charact. 62, 535 (2011).CrossRefGoogle Scholar
Yamasaki, M., Anan, T., Yoshimoto, S., and Kawamura, Y.: Mechanical properties of warm-extruded Mg-Zn-Gd alloy with coherent 14H long periodic stacking ordered structure precipitate. Scr. Mater. 53, 799 (2005).CrossRefGoogle Scholar
Wang, J.L., Dong, H.W., Wang, L.D., Wu, Y.M., and Wang, L.M.: Effect of hot rolling on the microstructure and mechanical properties of Mg-5Al-0.3Mn-2Nd alloy. J. Alloys Compd. 507, 178 (2010).CrossRefGoogle Scholar
Itoi, T., Seimiya, T., Kawamura, Y., and Hirohashi, M.: Long period stacking structures observed in Mg97Zn1Y2 alloy. Scr. Mater. 51, 107 (2004).CrossRefGoogle Scholar
Anyanwu, I.A., Kamado, S., and Kojima, Y.: Creep properties of Mg-Gd-Y-Zr alloys. Mater. Trans. 42, 1206 (2001).CrossRefGoogle Scholar
Liu, K., Zhang, J.H., Sun, W., Qiu, X., Lu, H.Y., Tang, D.X., Rokhlin, L.L., Elkin, F.M., and Meng, J.: Precipitates formed in a Mg-7Y-4Gd-0.5Zn-0.4Zr alloy during isothermal ageing at 250°C. Mater. Chem. Phys. 117, 107 (2009).CrossRefGoogle Scholar
Gao, X., He, S.M., Zeng, X.Q., Peng, L.M., Ding, W.J., and Nie, J.F.: Microstructure evolution in a Mg-15Gd-0.5Zr(wt.%) alloy during isothermal aging at 250°C. Mater. Sci. Eng., A 431, 322 (2006).CrossRefGoogle Scholar
Mabuchi, M. and Higashi, K.: Strengthening mechanisms of Mg-Si alloys. Acta Mater. 44, 4611 (1996).CrossRefGoogle Scholar
Yang, Z., Li, J.P., Guo, Y.C., Liu, T., Xia, F., Zeng, Z.W., and Liang, M.X.: Precipitation process and effect on mechanical properties of Mg-9Gd-3Y-0.6Zn-0.5Zr alloy. Mater. Sci. Eng., A 454–455, 274 (2007).CrossRefGoogle Scholar
Nie, J.F.: Effects of precipitate shape and orientation on dispersion strengthening in magnesium alloys. Scr. Mater. 48, 1009 (2003).CrossRefGoogle Scholar
He, S.M., Zeng, X.Q., Peng, L.M., Gao, X., Nie, J.F.,and Ding, W.J.: Microstructure and strengthening mechanism of high strength Mg-10Gd-2Y-0.5Zr alloy. J. Alloys Compd. 427, 316 (2007).CrossRefGoogle Scholar
Abe, E., Kawamura, Y., Hayashi, K., and Inoue, A.: Long-period ordered structure in a high-strength nanocrystalline Mg-1at%Zn-2at%Y alloy studied by atomic-resolution Z-contrast STEM. Acta Mater. 50, 3845 (2002).CrossRefGoogle Scholar
Jäger, A., Lukáč, P., Gärtnerová, V., Bohlen, J., and Kainer, K.U.: Tensile properties of hot rolled AZ31 Mg alloy sheets at elevated temperatures. J Alloys Compd. 378, 184 (2004).CrossRefGoogle Scholar
Yi, S.B., Zaefferer, S., and Brokmeier, H-G.: Mechanical behaviour and microstructural evolution of magnesium alloy AZ31 in tension at different temperatures. Mater. Sci. Eng., A 424, 275 (2006).CrossRefGoogle Scholar
Tan, J.C. and Tan, M.J.: Superplasticity and grain boundary sliding characteristics in two stage deformation of Mg-3Al-1Zn alloy sheet. Mater. Sci. Eng., A 339, 81 (2003).CrossRefGoogle Scholar
Li, K-J. and Li, Q-A.: Microstructure and superior mechanical properties of cast Mg-12Gd-2Y-0.5Sm-0.5Sb-0.5Zr alloy. Mater. Sci. Eng., A 528, 5453 (2011).CrossRefGoogle Scholar
Liu, K., Rokhlin, L.L., Elkin, F.M., Tang, D.X., and Meng, J.: Effect of ageing treatment on the microstructures and mechanical properties of the extruded Mg-7Y-4Gd-1.5Zn-0.4Zr alloy. Mater. Sci. Eng., A 527, 828 (2010).CrossRefGoogle Scholar