Hostname: page-component-586b7cd67f-dlnhk Total loading time: 0 Render date: 2024-11-24T15:34:52.832Z Has data issue: false hasContentIssue false
  • English
  • Français

Microindentation of titanium: Dependence of plastic energy on the indentation depth and time-dependent plastic deformation

Published online by Cambridge University Press:  31 January 2011

Rong Chen ,
Fuqian Yang ,
M. Ashraf Imam ,
C.R. Feng  and
Peter Pao
Rong Chen
Affiliation:
Department of Chemical and Materials Engineering, University of Kentucky, Lexington, Kentucky 40506
Fuqian Yang*
Affiliation:
Department of Chemical and Materials Engineering, University of Kentucky, Lexington, Kentucky 40506
M. Ashraf Imam
Affiliation:
Material Science and Technology Division, Naval Research Laboratory, Washington, DC 20375
C.R. Feng
Affiliation:
Material Science and Technology Division, Naval Research Laboratory, Washington, DC 20375
Peter Pao
Affiliation:
Material Science and Technology Division, Naval Research Laboratory, Washington, DC 20375
*
a)Address all correspondence to this author.e-mail: [email protected]
Get access

Abstract

The cavity model and the dislocation mechanics were used to analyze the plastic energy dissipated in an indentation deformation. The plastic energy dissipated in an indentation cycle was proportional to the cube of the residual indentation depth. The experimental results supported the analysis for the indentation of commercially pure titanium by a Vickers indenter. Slip bands around the indentation were observed, suggesting that the indentation deformation was controlled by dislocation motion. The indentation hardness decreased with the indentation load, showing the indentation size effect. The ratio of the total energy to the plastic energy was found to be proportional to the ratio of the maximum indentation depth to the residual indentation depth. The effects of holding time were examined on the time-dependent plastic deformation of the commercially pure titanium at ambient temperature.

Keywords

Hardness
Type
Articles
Information
Journal of Materials Research , Volume 23 , Issue 4 , April 2008 , pp. 1068 - 1075
Copyright
Copyright © Materials Research Society 2008

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1Akhtar, A.Teghtsoonian, E.: Prismatic slip in alpha-titanium single-crystals. Metall. Trans. A 6, 2201 1975CrossRefGoogle Scholar
2Akhtar, A.: Basal slip and twinning in alpha-titanium single-crystals. Metall. Trans. A 6, 1105 1975CrossRefGoogle Scholar
3Nemat-Nasser, S., Guo, W.G.Cheng, J.Y.: Mechanical properties and deformation mechanism of a commercially pure titanium. Acta Mater. 47, 3705 1999CrossRefGoogle Scholar
4Tsuchiya, T., Hirata, M.Chiba, N.: Young’s modulus, fracture strain, and tensile strength of sputtered titanium thin films. Thin Solid Films 484, 245 2005CrossRefGoogle Scholar
5Lütjering, G., Williams, J.C.Gysler, A.: Microstructure and mechanical properties of titanium alloys in Microstructure and Properties of Materials, Vol. 2 edited by J.C.M. Li World Scientific Hackensack, NJ 2000 1Google Scholar
6Huang, L., Lu, J.Troyon, M.: Nanomechanical properties of nanostructured titanium prepared by SMAT. Surf. Coat. Technol. 201, 208 2006CrossRefGoogle Scholar
7Mante, F.K., Baran, G.R.Lucas, B.: Nanoindentation studies of titanium single crystals. Biomaterials 20, 1051 1999CrossRefGoogle ScholarPubMed
8Bishop, R.F., Hill, R.Mott, N.F.: The theory of indentation and hardness tests. Proc. Phys. Soc. 57, 147 1945CrossRefGoogle Scholar
9Marsh, D.M.: Plastic flow in glass. Proc. R. Soc. London Ser. A 279, 420 1964Google Scholar
10Johnson, K.L.: Correlation of indentation experiments. J. Mech. Phys. Solids 18, 115 1970CrossRefGoogle Scholar
11Ai, K.Dai, L.H.: A new modified expanding cavity model for characterizing the spherical indentation behaviour of bulk metallic glass with pile-up. Scripta Mater. 56, 761 2007CrossRefGoogle Scholar
12Gao, X.L.: An expanding cavity model incorporating strain-hardening and indentation size effects. Int. J. Solids Struct. 43, 6615 2006CrossRefGoogle Scholar
13Gao, X.L., Jing, X.N.Subhash, G.: Two new expanding cavity models for indentation deformations of elastic strain-hardening materials. Int. J. Solids Struct. 43, 2193 2006CrossRefGoogle Scholar
14Ashby, M.F.: Deformation of plastically non-homogeneous materials. Philos. Mag. 21, 399 1970CrossRefGoogle Scholar
15Conrad, H., Okazaki, K., Gadgil, V.Jon, M.: Electron Microscopy and Strength of Materials Univ. California Press Berkeley, CA 1972 453Google Scholar
16Yang, F.Q., Peng, L.L.Okazaki, K.: Microindentation of aluminum. Metall. Mater. Trans. A 35, 3323 2004CrossRefGoogle Scholar
17Hill, R.: The Mathematical Theory of Plasticity The Clarendon Press Oxford, UK 1967 106Google Scholar
18Meyers, M.A.Chawla, K.K.: Mechanical Behavior of Materials Prentice Hall Englewood Cliffs, NJ 2002 212Google Scholar
19Hosford, W.F.: Physical Metallurgy Taylor & Francis New York 2005 Chap. 9,Google Scholar
20Oliver, W.C.Pharr, G.M.: An improved technique for determining hardness and elastic-modulus using load and displacement sensing indentation experiments. J. Mater. Res. 7, 1564 1992CrossRefGoogle Scholar
21Hay, J.L., Oliver, W.C., Bolshakv, A.Pharr, G.M.: Using the ratio of loading slope and elastic stiffness to predict pile-up and constraint factor during indentation in Fundamentals of Nanoindentation and Nanotribology, edited by N.R. Moody, W.W. Gerberich, N. Burnham, and S.P. Baker (Mater. Res. Soc. Symp. Proc. 522, Warrendale, PA, 1998), p. 101CrossRefGoogle Scholar
22Yang, F.Q., Geng, K., Liaw, P.K., Fan, G.Choo, H.: Deformation in a Zr57Ti5Cu20Ni8Al10 bulk metallic glass during nanoindentation. Acta Mater. 55, 321 2007CrossRefGoogle Scholar
23Chen, R., Yang, F.Q., Liaw, P.K., Fan, G.Choo, H.: Microindentation of a Zr57Ti5Cu20Ni8Al10 bulk metallic glass. Mater. Trans. 48, 1743 2007CrossRefGoogle Scholar
24Dieter, G.E.Mechanical Metallurgy, 2nd ed.McGraw-Hill, Inc. New York 1976 392Google Scholar
25Pugno, N.M.: A general shape/size-effect law for nanoindentation. Acta Mater. 55, 1947 2007CrossRefGoogle Scholar
26Nowak, R.Sakai, M.: Energy principle of indentation contact - the application to sapphire. J. Mater. Res. 8, 1068 1993CrossRefGoogle Scholar
27Menčik, J.Swain, M.V.: Micro-indentation tests with pointed indenters. Mater. Forum 18, 277 1994Google Scholar
28Cheng, Y.T.Cheng, C.M.: Scaling, dimensional analysis, and indentation measurements. Mater. Sci. Eng., R 44, 91 2004CrossRefGoogle Scholar
29Argon, A.S.Backer, S.McClintock, F.A.Reichenbach, G.S.Orowan, E.Shaw, M.C.Rabinowicz, E.: Mechanical Behavior of Materials Addison-Wesley Publishing Co., Inc. Reading, MA 1966 637Google Scholar