Hostname: page-component-586b7cd67f-t7czq Total loading time: 0 Render date: 2024-11-28T05:12:37.149Z Has data issue: false hasContentIssue false

Mechanism of shear band formation and dynamic softening in a two-phase (α2 + γ) titanium aluminide

Published online by Cambridge University Press:  02 June 2020

Nitish Bibhanshu*
Affiliation:
Department of Materials Engineering, Indian Institute of Science, Bangalore 560012, India
Satyam Suwas*
Affiliation:
Department of Materials Engineering, Indian Institute of Science, Bangalore 560012, India
*
a)Address all correspondence to these authors. e-mail: [email protected]
Get access

Abstract

The formation of shear bands during hot deformation of a two-phase (α2 + γ) titanium aluminide and its consequences on dynamics softening has been investigated. The starting material consists of a colony of lamellar grains along with the segregated vanadium and niobium which was subjected to hot deformation in the temperature range 1000–1175 °C at the strain rate 10 s−1. Microstructures of the deformed samples indicate that, with increase in the deformation temperature, the orientation of shear bands changes. Moreover, the extent of dynamic recrystallization also increases with deformation temperature. The softening behaviour and crystallographic orientation change within lamellae during hot deformation have been explored. The nucleation of newly recrystallized grains has been observed at twin–parent grain boundary and within the twined γ phase. Lamellae of the γ and α2 phase have been also observed to be twisted and tilted, leading to the band formations under the load, whose mechanisms have also been explored in the present study.

Type
Article
Copyright
Copyright © Materials Research Society 2020

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

Semiatin, S.L., Seetharaman, V., and Jain, V.K.: Microstructure development during conventional and isothermal hot forging of a near-gamma titanium aluminide. Metall. Mater. Trans. A 25, 2753 (1994).CrossRefGoogle Scholar
Dey, S.R., Bouzy, E., and Hazotte, A.: Features of feathery gamma structure in a near gamma TiAl alloy. Acta Mater. 56, 2051 (2008).CrossRefGoogle Scholar
Kanani, M., Hartmaier, A., and Janisch, R.: Stacking fault based analysis of shear mechanisms at interfaces in lamellar TiAl alloys. Acta Mater. 106, 208 (2016).CrossRefGoogle Scholar
Bibhanshu, N., Bhattacharjee, A., and Suwas, S.: Hot deformation response of titanium aluminides Ti–45Al–(5, 10)Nb–0.2B–0.2C with pre-conditioned microstructures. J. Alloys Compd. 832, 154584 (2020).10.1016/j.jallcom.2020.154584CrossRefGoogle Scholar
Fergus, J.W.: Review of the effect of alloy composition on the growth rates of scales formed during oxidation of gamma titanium aluminide alloys. Mater. Sci. Eng., A 338, 108 (2002).CrossRefGoogle Scholar
Donchev, A., Richter, E., Schütze, M., and Yankov, R.: Improvement of the oxidation behaviour of TiAl-alloys by treatment with halogens. Intermetallics 14, 1168 (2006).10.1016/j.intermet.2005.11.032CrossRefGoogle Scholar
Imayev, V., Oleneva, T., Imayev, R., Christ, H-J., and Fecht, H-J.: Microstructure and mechanical properties of low and heavy alloyed γ-TiAl + α2-Ti3Al based alloys subjected to different treatments. Intermetallics 26, 91 (2012).CrossRefGoogle Scholar
Franzén, S.F. and Karlsson, J.: γ-Titanium Aluminide Manufactured by Electron Beam Melting (Gothenburg, Sweden 2010); p. 89.Google Scholar
Gerling, R., Schimansky, F.P., Stark, A., Bartels, A., Kestler, H., Cha, L., Scheu, C., and Clemens, H.: Microstructure and mechanical properties of Ti 45Al 5Nb + (0–0.5C) sheets. Intermetallics 16, 689 (2008).CrossRefGoogle Scholar
Nochovnaya, N.A., Panin, P.V., Kochetkov, A.S., and Bokov, K.A.: Modern refractory alloys based on titanium gamma-aluminide: Prospects of development and application. Met. Sci. Heat Treat. 56, 364 (2014).CrossRefGoogle Scholar
Estrada, C.A.: New technology used in gas turbine blade materials. Sci. Tech. Año XIII 36, 297 (2007).Google Scholar
Lasalmonie, A.: Intermetallics: Why is it so difficult to introduce them in gas turbine engines? Intermetallics 14, 1123 (2006).CrossRefGoogle Scholar
Ohnuma, I., Fujita, Y., Mitsui, H., Ishikawa, K., Kainuma, R., and Ishida, K.: Phase equilibria in the Ti–Al binary system. Acta Mater. 48, 3113 (2000).CrossRefGoogle Scholar
Hu, D., Yang, C., Huang, A., Dixon, M., and Hecht, U.: Grain refinement in beta-solidifying Ti44Al8Nb1B. Intermetallics 23, 49 (2012).10.1016/j.intermet.2011.12.022CrossRefGoogle Scholar
Appel, F., Paul, J.D.H., and Oehring, M.: Gamma Titanium Aluminide Alloys, First (WILEY-VCH Verlag GmbH & Co. KGaA, Germany, 2011).CrossRefGoogle Scholar
Roy, S. and Suwas, S.: The influence of temperature and strain rate on the deformation response and microstructural evolution during hot compression of a titanium alloy Ti–6Al–4V–0.1B. J. Alloys Compd. 548, 110 (2013).10.1016/j.jallcom.2012.08.123CrossRefGoogle Scholar
Liu, B., Li, J., and Hu, D.: Solidification and grain refinement in Ti(48–50)Al2Mn2Nb1B alloys. Intermetallics 101, 99 (2018).CrossRefGoogle Scholar
Zhou, H., Kong, F., Wang, X., and Chen, Y.: Hot deformation behavior and microstructural evolution of as-forged Ti–44Al–8Nb–(W, B, Y) alloy with nearly lamellar microstructure. Intermetallics 81, 6272 (2017).CrossRefGoogle Scholar
Bibhanshu, N. and Suwas, S.: Hot deformation and dynamic recrystallization in titanium aluminide. Mater. Sci. Forum 941, 13911396 (2018).CrossRefGoogle Scholar
Bibhanshu, N., Bhattacharjee, A., and Suwas, S.: Influence of temperature and strain rate on microstructural evolution during hot compression of Ti–45Al–xNb–0.2C–0.2B titanium aluminide alloys. Jom 71, 35523564 (2019).10.1007/s11837-019-03722-2CrossRefGoogle Scholar
Prasad, N., Bibhanshu, N., Nayan, N., Avadhani, G.S., and Suwas, S.: Hot deformation behavior of the high-entropy alloy CoCuFeMnNi. J. Mater. Res. 34, 744755 (2019).CrossRefGoogle Scholar
Roy, S. and Suwas, S.: Orientation dependent spheroidization response and macro-zone formation during sub β-transus processing of Ti–6Al–4V alloy. Acta Mater. 134, 283 (2017).CrossRefGoogle Scholar
Niu, H.Z., Chen, Y.Y., Kong, F.T., and Lin, J.P.: Microstructure evolution, hot deformation behavior and mechanical properties of Ti–43Al–6Nb–1B alloy. Intermetallics 31, 249 (2012).CrossRefGoogle Scholar
Zhang, S.Z., Zhang, C.J., Du, Z.X., Hou, Z.P., Lin, P., Kong, F.T., and Chen, Y.Y.: Deformation behavior of high Nb containing TiAl based alloy in α + γ two phase field region. Mater. Des. 90, 225 (2016).CrossRefGoogle Scholar
Stepanov, N.D., Shaysultanov, D.G., Yurchenko, N.Y., Zherebtsov, S.V., Ladygin, A.N., Salishchev, G.A., and Tikhonovsky, M.A.: High temperature deformation behavior and dynamic recrystallization in CoCrFeNiMn high entropy alloy. Mater. Sci. Eng., A 636, 188 (2015).CrossRefGoogle Scholar
Nicolaou, P.D. and Semiatin, S.L.: High-temperature deformation and failure of an orthorhombic titanium aluminide sheet material. Metall. Mater. Trans. A 27, 3675 (1996).CrossRefGoogle Scholar
Li, M., Xiao, S., Chen, Y., Xu, L., and Tian, J.: The effect of boron addition on the deformation behavior and microstructure of β-solidify TiAl alloys. Mater. Charact. 145, 312 (2018).CrossRefGoogle Scholar
Liu, H., Rong, R., Gao, F., Liu, Y., Li, Z., and Wang, Q.: Hot deformation mechanisms of an as-extruded TiAl alloy with large amount of remnant lamellae. J. Mater. Eng. Perform. 26, 3151 (2017).CrossRefGoogle Scholar
Ji, Z.W., Lu, S., miao Hu, Q., Kim, D., Yang, R., and Vitos, L.: Mapping deformation mechanisms in lamellar titanium aluminide. Acta Mater. 144, 835 (2018).CrossRefGoogle Scholar
Prokoshkina, D., Klinger, L., Moros, A., Wilde, G., Rabkin, E., and Divinski, S.V.: Effect of recrystallization on diffusion in ultrafine-grained Ni. Acta Mater. 69, 314 (2014).10.1016/j.actamat.2014.02.002CrossRefGoogle Scholar
Edalati, K., Matsuda, J., Iwaoka, H., Toh, S., Akiba, E., and Horita, Z.: High-pressure torsion of TiFe intermetallics for activation of hydrogen storage at room temperature with heterogeneous nanostructure. Int. J. Hydrogen Energy 38, 4622 (2013).CrossRefGoogle Scholar
Kaibyshev, R. and Malopheyev, S.: Mechanisms of dynamic recrystallization in aluminum alloys. Mater. Sci. Forum 794–796, 784 (2014).CrossRefGoogle Scholar
Dey, S.R., Morawiec, A., Fundenberger, J.J., Hazotte, A., and Bouzy, E.: Variant orientation distribution in a near-γ Ti–Al alloy with a lamellar microstructure. Solid State Phenom. 105, 145 (2005).10.4028/www.scientific.net/SSP.105.145CrossRefGoogle Scholar
Seetharaman, V. and Semiatin, S.L.: Effect of the lamellar grain size on plastic flow behavior and microstructure evolution during hot working of a gamma titanium aluminide alloy. Metall. Mater. Trans. A 33, 3817 (2002).CrossRefGoogle Scholar
Li, T.R., Liu, G.H., Xu, M., Wang, B.X., Misra, R.D.K., and Wang, Z.D.: High temperature deformation and control of homogeneous microstructure during hot pack rolling of Ti-44Al-5Nb-(Mo, V, B) alloys: The impact on mechanical properties, Mater. Sci. Eng., A 751, 1 (2019).CrossRefGoogle Scholar
Roy, S., Sarkar, A., and Suwas, S.: On characterization of deformation microstructure in Boron modified Ti–6Al–4V alloy. Mater. Sci. Eng., A 528, 449 (2010).CrossRefGoogle Scholar
Du, Z., Jiang, S., and Zhang, K.: The hot deformation behavior and processing map of Ti–47.5Al–Cr–V alloy. Mater. Des. 86, 464 (2015).CrossRefGoogle Scholar
Chaudhuri, A., Sarkar, A., Kapoor, R., Singh, R.N., Chakravartty, J.K., and Suwas, S.: Microstructural features of hot deformed Nb–1Zr–0.1C alloy. Jom 66, 1923 (2014).CrossRefGoogle Scholar
Suwas, S. and Ray, R.K.: Evolution of texture in the β(B2) phase of a two-phase titanium aluminide intermetallic alloy Ti–24Al–11Nb. Metall. Mater. Trans. A 31, 2339 (2000).CrossRefGoogle Scholar
Roy, S., Suwas, S., Tamirisakandala, S., Srinivasan, R., and Miracle, D.B., Processing response of boron modified Ti-6A1-4V alloy in (alpha+beta) working regime, TMS 2009 - 138th Annu. Meet. Exhib (Location - San Francisco, California). February. 15 - 19, 2009. 3 (2009) 6370.Google Scholar
An, Q., Reddy, K.M., Qian, J., Hemker, K.J., Chen, M.W., and Goddard, W.A. III: Nucleation of amorphous shear bands at nanotwins in boron suboxide. Nat. Commun. 7, 11001 (2016).CrossRefGoogle ScholarPubMed