Hostname: page-component-cd9895bd7-7cvxr Total loading time: 0 Render date: 2024-12-29T02:31:11.640Z Has data issue: false hasContentIssue false
  • English
  • Français

Low temperature, transient liquid phase sintering of B2O3-SiO2-doped Nd:YAG transparent ceramics

Published online by Cambridge University Press:  28 April 2011

Adam J. Stevenson ,
Elizabeth R. Kupp  and
Gary L. Messing
Adam J. Stevenson*
Affiliation:
Department of Materials Science and Engineering and Materials Research Institute, The Pennsylvania State University, University Park, Pennsylvania 16802
Elizabeth R. Kupp
Affiliation:
Department of Materials Science and Engineering and Materials Research Institute, The Pennsylvania State University, University Park, Pennsylvania 16802
Gary L. Messing
Affiliation:
Department of Materials Science and Engineering and Materials Research Institute, The Pennsylvania State University, University Park, Pennsylvania 16802
*
a)Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

B2O3-SiO2 is shown to act as a transient liquid phase sintering aid that reduces the sintering temperature of Nd:YAG ceramics to 1600 °C. 1 at.% Nd3xY3-3xAl5O12 (Nd:YAG) ceramics were doped with 0.34–1.35 mol% B2O3-SiO2 and sintered between 1100 and 1700 °C. Dilatometric measurements show that B2O3-SiO2 doping increases the densification rate during intermediate-stage sintering relative to SiO2-doped samples. B3+ content is reduced to <5 ppm in samples heated to 1500 °C, as determined by mass spectrometry. For B2O3-SiO2-doped samples, final stage densification and grain growth follow a more densifying sintering trajectory than SiO2-doped 1 at.% Nd:YAG ceramics because there is less SiO2 during final-stage densification. The increased densification kinetics during intermediate-stage sintering lead to highly transparent Nd:YAG ceramics when sintered at 1600 °C in either vacuum or oxygen. Thus, transparent Nd:YAG ceramics can be sintered without the need for expensive refractory metal vacuum furnaces or pressure-assisted densification.

Keywords

SinteringOpticalDensification
Type
Articles
Information
Journal of Materials Research , Volume 26 , Issue 9 , 14 May 2011 , pp. 1151 - 1158
Copyright
Copyright © Materials Research Society 2011

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Ikesue, A., Furusato, I., and Kamata, K.: Fabrication of polycrystalline, transparent YAG ceramics by a solid-state reaction method. J. Am. Ceram. Soc. 78(1), 225 (1995).CrossRefGoogle Scholar
2.Yagi, H., Yanagitani, T., and Ueda, K.-I.: Nd3+:Y3Al5O12 laser ceramics: Flashlamp pumped laser operation with a UV cut filter. J. Alloys Compd. 421(1–2), 195 (2006).CrossRefGoogle Scholar
3.Fabrichnaya, O., Seifert, H.J., Weiland, R., Ludwig, T., Aldinger, F., and Navrotsky, A.: Phase equilibria and thermodynamics in the Y2O3-Al2O3-SiO2-system. Z. Fur Metal. 92(9), 1083 (2001).Google Scholar
4.Boulesteix, R., Maître, A., Baumard, J.-F., Sallé, C., and Rabinovitch, Y.: Mechanism of the liquid-phase sintering for Nd:YAG ceramics. Opt. Mater. 31(5), 711 (2009).CrossRefGoogle Scholar
5.Stevenson, A.J., Li, X., Martinez, M.A., Anderson, J.M., Suchy, D.L., Kupp, E.R., Dickey, E.C., Mueller, K.T., and Messing, G.L.: Effect of SiO2 doping on densification and microstructure in transparent Nd:YAG ceramics. J. Am. Ceram. Soc., 94: doi: 10.1111/j.1551-2916.2010.04260.x (in press).Google Scholar
6.Taylor, D.J., Dent, D.Z., Braski, D.N., and Fabes, B.D.: Boron loss in furnace- and laser-fired, sol-gel derived borosilicate glass films. J. Mater. Res. 11(8), 1870 (1996).CrossRefGoogle Scholar
7.Shelby, J.E.: Introduction to Glass Science and Technology (Royal Society of Chemistry, Cambridge, UK, 2005).CrossRefGoogle Scholar
8.Lee, S.-H., Kupp, E.R., Stevenson, A.J., Anderson, J.M., Messing, G.L., Li, X., Dickey, E.C., Dumm, J.Q., Simonaitis-Castillo, V.K., and Quarles, G.J.: Hot isostatic pressing of transparent Nd:YAG ceramics. J. Am. Ceram. Soc. 92(7), 1456 (2009).CrossRefGoogle Scholar
9.Kochawattana, S.: Phase Formation and Sintering of YAG Ceramics, Ph.D. Dissertation, The Pennsylvania State University, University Park, PA, 2007.Google Scholar
10.Maître, A., Sallé, C., Boulesteix, R., Baumard, J.-F., and Rabinovitch, Y.: Effect of silica on the reactive sintering of polycrystalline Nd:YAG ceramics. J. Am. Ceram. Soc. 91(2), 406 (2008).CrossRefGoogle Scholar
11.Kwon, O.-H. and Messing, G.L.: A theoretical analysis of solution-precipitation controlled densification during liquid phase sintering. Acta Metall. Mater. 39(9), 2059 (1991).CrossRefGoogle Scholar
12.Stebbins, J.F.: Temperature effects on the network structure of oxide melts and their consequences for configurational heat capacity. Chem. Geol. 256(3/4), 80 (2008).CrossRefGoogle Scholar