Hostname: page-component-78c5997874-8bhkd Total loading time: 0 Render date: 2024-11-02T20:01:42.386Z Has data issue: false hasContentIssue false
  • English
  • Français

Lead Zirconate Titanate Via Reaction Sintering of Hydroxide Precursors

Published online by Cambridge University Press:  31 January 2011

Xue Junmin  and
John Wang
Xue Junmin
Affiliation:
Department of Materials Science, Faculty of Science, National University of Singapore, 119260 Singapore
John Wang*
Affiliation:
Department of Materials Science, Faculty of Science, National University of Singapore, 119260 Singapore
*
a)Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

Lead zirconate titanate (PZT) has been successfully fabricated via a unique one-step sintering processing route, which is simpler than the traditional precursor-calcinationmilling- pelleting-sintering route and is able to deliver an enhanced sintered density at a much reduced sintering temperature. The hydroxide precursor was prepared by coprecipitation from a mixed nitrate solution containing Pb2+, Zr4+, and Ti4+ ions, and it was then compacted into pellets without being calcined at a low temperature. The precursor pellets were dehydrated at 400, 500, and 600 °C for 4 h, respectively, followed by an isostatic pressing at 350 MPa, prior to being sintered at a high temperature. Dehydration temperature has a large impact on the sintering behavior of these hydroxide-derived PZT ceramics. The PZT dehydrated at 400 °C was seriously cracked when sintered at temperatures ranging from 950 to 1150 °C, due to the incomplete dehydration. A sintered density of 99.2% theoretical density was obtained at 1050 °C for 2 h for the powder pellet dehydrated at 500 °C for 4 h. It exhibits a dielectric constant of 1024 and a dielectric loss of 2.1% at a frequency of 1 kHz at room temperature. A calcination at a too-high temperature, e.g., 600 °C, results in a reduction in the sinterability of the precipitate-derived PZT ceramic.

Type
Articles
Information
Journal of Materials Research , Volume 14 , Issue 4 , April 1999 , pp. 1503 - 1509
Copyright
Copyright © Materials Research Society 1999

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Kingon, A.I. and Clark, J. B., J. Am. Ceram. Soc. 66 (4), 253–256 (1983).CrossRefGoogle Scholar
2.Leite, E. R., Cerqueira, M., Parazoli, L. A., Nasar, R. S., Longo, E., and Varela, J. A., J. Am. Ceram. Soc. 79 (6), 1563–1568 (1996).CrossRefGoogle Scholar
3.Ramji, L., Krishnan, R., and Ramakrishnan, P., Mater. Sci. Eng. 96, 1250–1255 (1987).Google Scholar
4.Choy, J. H., Han, Y. S., and Kim, J. T., J. Mater. Chem. 5 (1), 65–69 (1995).CrossRefGoogle Scholar
5.Cheng, H.M., Ma, J.M., Zhu, B., and Cui, Y.H., J. Am. Ceram. Soc. 76 (3), 625–629 (1993).CrossRefGoogle Scholar
6.Ogihara, T., Kaneko, H., Mizutani, N., and Kato, M., J. Mater. Sci. Lett. 7, 867–869 (1988).CrossRefGoogle Scholar
7.Tandon, R. P., Singh, V., and Singh, R., J. Mater. Sci. Lett. 13, 810–812 (1994).CrossRefGoogle Scholar
8.Tuan, W.H. and Lin, M.C., J. Mater. Sci. Lett. 15, 735–737 (1996).CrossRefGoogle Scholar
9.Rahaman, M. N. and Jonghe, L.C. D., J. Am. Ceram. Soc. 76 (7), 1739–1744 (1993).CrossRefGoogle Scholar
10.Hong, W.S., Jonghe, L.C.D, Yang, X., and Rahaman, M.N., J. Am. Ceram. Soc. 78 (12), 3217–3224 (1995).CrossRefGoogle Scholar
11.Boch, P. and Giny, J. P., Mater. Sci. Eng. 71, 39–48 (1985).CrossRefGoogle Scholar
12.Shrout, T.R., Papet, P., Kim, S., and Lee, G., J. Am. Ceram. Soc. 73 (7), 1862–1867 (1990).CrossRefGoogle Scholar
13.Kim, S., Lee, G. S., Shrout, T. R., and Venktanari, S., J. Mater. Soc. 26, 4411–4415 (1991).CrossRefGoogle Scholar
14.Chandratreya, S.S., Fulrath, R. M., and Pask, J.A., J. Am. Ceram. Soc. 64 (7), 422–425 (1981).CrossRefGoogle Scholar
15.Infrared and Raman Spectra of Inorganic and Coordination Compounds, edited by Nakamoto, K. (New York, 1986), p. 228.Google Scholar
16.Lucuta, D.G., Coustantinescu, F., and Barb, D., J. Am. Ceram. Soc. 68 (10), 533–537 (1985).CrossRefGoogle Scholar
17.Sintering Theory and Practice, edited by Kolar, D., Pejovnik, S., and Ristic, M.M. (Amsterdam, 1982), p. 145.Google Scholar
18.Young, R.J., Wu, T. B., and Lin, I. N., J. Mater. Sci. 25, 3566–3572 (1990).CrossRefGoogle Scholar
19.Tuan, W. H., Gilbart, E., and Brook, R. J., J. Mater. Sci. 24, 1062–1067 (1989).CrossRefGoogle Scholar
20.Phule, P.P. and Risbud, S. H., J. Mater. Sci. 25, 1169–1183 (1990).CrossRefGoogle Scholar