Hostname: page-component-586b7cd67f-rdxmf Total loading time: 0 Render date: 2024-11-24T12:34:34.187Z Has data issue: false hasContentIssue false
  • English
  • Français

Interfacial characteristics and mechanical properties of a modified Nb-containing Zr-based bulk metallic glass composite reinforced with W fiber

Published online by Cambridge University Press:  31 January 2011

M.L. Wang ,
X. Hui  and
G.L. Chen
M.L. Wang
Affiliation:
State Key Laboratory for Advanced Metals and Materials, University of Science and Technology Beijing, Beijing 100083, China
X. Hui*
Affiliation:
State Key Laboratory for Advanced Metals and Materials, University of Science and Technology Beijing, Beijing 100083, China
G.L. Chen
Affiliation:
State Key Laboratory for Advanced Metals and Materials, University of Science and Technology Beijing, Beijing 100083, China
*
a) Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

Tungsten (W) fiber reinforced Zr47Ti13Cu11Ni10Be16Nb3 bulk metallic glass composite has been prepared by melt infiltration casting. Interfacial characteristics of the composite were analyzed by sessile drop technique, x-ray diffraction (XRD), scanning electron microscopy (SEM), electron probe x-ray microanalysis (EPMA), and nanoindenter. Results indicate that Zr47Ti13Cu11Ni10Be16Nb3 melt wets the W substrate, and the interfacial bond composed of a diffusion–dissolution layer between Zr47Ti13Cu11Ni10Be16Nb3 matrix and W fiber is in good condition. Due to these excellent interfacial characteristics, the mechanical properties of the composite are considerably enhanced with increasing volume fraction of W fiber. It was found that the compressive strength of 70% volume fraction of W fiber composite is 2.6 GPa, which is 58% higher than the value exhibited by the unreinforced matrix. At the same time, the reinforced matrix exhibits 13% plastic deformation when tested under quasi-static compression conditions. Instead of shear mode seen for the unreinforced matrix, the failure mode of the 70% volume fraction W fiber composite is mainly caused by fiber splitting and buckling. Also, the W fiber hinders localized shear bands from propagating and gives rise to multiple shear bands, which results in the enhancement of the compressive strength and plastic deformation.

Keywords

Composite
Type
Articles
Information
Journal of Materials Research , Volume 23 , Issue 2 , February 2008 , pp. 320 - 327
Copyright
Copyright © Materials Research Society 2007

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1Hufnagel, T.C., EI-Deiry, P.Vinci, R.P.: Development of shear band structure during deformation of a Zr57Ti5Cu20Ni8Al10 bulk metallic glass. Scripta Mater. 43(12), 1071 2002CrossRefGoogle Scholar
2Li, J.X., Shan, G.B.Gao, K.W.: In situ SEM study of formation and growth of shear bands and microcracks in bulk metallic glasses. Mater. Sci. Eng., A 354, 337 2003CrossRefGoogle Scholar
3Leng, Y.Courtney, T.H.: Fracture behavior of laminated metal-metallic glass composites. Metall. Trans. A 21A, 2159 1990CrossRefGoogle Scholar
4Leng, Y.Courtney, T.H.: Some tensile properties of metal-metallic glass laminates. J. Mater. Sci. 24, 2006 1989CrossRefGoogle Scholar
5Leng, Y.Courtney, T.H.: Multiple shear band formation in metallic in composites. J. Mater. Sci. 26, 588 1991CrossRefGoogle Scholar
6Hufnagel, T.C., Fan, C., Ott, R.T., Li, J.Brennan, S.: Controlling shear band behavior in metallic glassed through microstructure design. Intermetallics 10, 1163 2002CrossRefGoogle Scholar
7Kim, H.S.: Strengthening mechanisms of Zr-based devitrified amorphous alloy nanocomposites. Scripta Mater. 48, 43 2003CrossRefGoogle Scholar
8Eckert, J., Kuhn, U.Mattern, N.: Structural bulk metallic glasses with different length-scale of constituent phases. Intermetallics 10, 1183 2002CrossRefGoogle Scholar
9Leonhard, A., Xing, L.Q.Heilmaier, M.: Effect of crystalline precipitations on the mechanical behavior of bulk glass forming Zr-based alloys. Nanostruct. Mater. 10(5), 805 1998CrossRefGoogle Scholar
10Conner, R.D., Dandliker, R.B.Johnson, W.L.: Mechanical properties of tungsten and steel fiber reinforced ZrTiCuNiBe metallic glass matrix composites. Acta Mater. 46(17), 6089 1998CrossRefGoogle Scholar
11Qiu, K.Q., Wang, A.M.Zhang, H.F.: Mechanical properties of tungsten fiber reinforced ZrAlNiCuSi metallic glass matrix composite. Intermetallic 10, 1283 2002CrossRefGoogle Scholar
12Schroers, J.: Characterization of the interface between the bulk glass forming alloy ZrTiCuNiBe with metals and ceramics. J. Mater. Res. 15(7), 1679 2000CrossRefGoogle Scholar
13Wang, M., Hui, X.Chen, G.: Influence of Nb on the interface structure of tungsten fiber reinforced Zr-based metallic glass composites. Mater. Sci. Forum 475–479, 3389 2005CrossRefGoogle Scholar
14Sylvan, Z. Beer: Liquid Metals—Chemistry and Physics Marcel Dekker, Inc. New York 1972 200–205Google Scholar
15Dandliker, R.B., Conner, R.D.Johnson, W.L.: Melt infiltration casting of bulk metallic-glass matrix composites. J. Mater. Res. 13, 2896 1998CrossRefGoogle Scholar
16Eustathopoulos, N.: Dynamics of wetting in reactive metal/ceramic system. Acta Mater. 46(7), 2319 1998Google Scholar
17Siewert, T.A., Heine, R.W.Lagally, M.G.: Braze alloy spreading on steel. Weld. J. 57, 31 1978Google Scholar
18Qiao, D-C., Zhang, H-F.Qin, F-X.: Wetting behaviors of molten Zr55Al10Ni5Cu30 on 1Cr18Ni9Ti. Chin. J. Nonferrous Met. 14(3), 484 2004Google Scholar
19Wang, M.L., Chen, G.L.Hui, X.D.: Optimized interface and mechanical properties of tungsten fiber/Zr-based bulk metallic glass composites. Intermetallics 15(10), 1309 2007CrossRefGoogle Scholar
20Metcalfe, A.G.: Interface in Metallic Matrix Composites Academic Press, Inc. New York 1974 2–3Google Scholar