Hostname: page-component-586b7cd67f-r5fsc Total loading time: 0 Render date: 2024-11-28T07:49:35.298Z Has data issue: false hasContentIssue false
  • English
  • Français

Influence of TiN particles on the wear behavior of silicon nitride–based composites

Published online by Cambridge University Press:  03 March 2011

Chien-Cheng Liu  and
Jow-Lay Huang
Chien-Cheng Liu
Affiliation:
Department of Material Science and Engineering, National Cheng-Kung University, Tainan, Taiwan 701, Republic of China
Jow-Lay Huang
Affiliation:
Department of Material Science and Engineering, National Cheng-Kung University, Tainan, Taiwan 701, Republic of China
Get access

Abstract

The friction and wear behavior of Si3N4-based composites against AISI-52100 steel were investigated in the ball-on-disk mode in a nonlubrication reciprocation motion. It has been found that under the conditions used, all the ceramic components exhibited rather low friction and wear coefficients. For monolithic silicon nitride materials, high friction coefficients between 0.6 and 0.7 and wear coefficients between 1.63 × 10−8 and 1.389 × 10−6 mm3/N · m were measured. The contact load was varied from 100 to 300 N. By adding titanium nitride, the friction coefficients were reduced to a value between 0.4 and 0.5 and wear coefficients between 1.09 × 10−8 and 0.32 × 10−6 mm3/ N · m at room temperature. All materials and worn surfaces as well as wear debris were investigated by means of scanning electron microscopy, energy dispersive spectroscopy, x-ray diffraction, and transmission electron microscopy (TEM) before or after the tribological tests. The TEM micrographs of wear track revealed plastic deformation through twins and cracking along grain boundary which play an important role in the fracture mechanism.

Keywords

Hot pressingCeramicMicrostructure
Type
Articles
Information
Journal of Materials Research , Volume 19 , Issue 2 , February 2004 , pp. 542 - 549
Copyright
Copyright © Materials Research Society 2004

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1Kleebe, H.J., Pezzotti, G. and Ziegler, G.: J. Am. Ceram. Soc. 82, 1857 (1999).CrossRefGoogle Scholar
2Lee, W.H. and Kim, H.E.: J. Am. Ceram. Soc. 80, 2737 (1997).CrossRefGoogle Scholar
3Park, H. and Kim, H.E.: J. Am. Ceram. Soc. 80, 750 (1997).CrossRefGoogle Scholar
4Schneider, J.A. and Mukherjee, A.K.: J. Am. Ceram. Soc. 82, 761 (1999).CrossRefGoogle Scholar
5Lee, S.Y.: J. Am. Ceram. Soc. 81, 1262 (1998).CrossRefGoogle Scholar
6Takahashi, H., Shinohara, N., Uematsu, K. and Junichiro, T.: J. Am. Ceram. Soc. 79, 843 (1996).CrossRefGoogle Scholar
7Gogotsi, Y.U. and Grathwohl, G.: J. Mater. Sci. 28, 4279 (1993).CrossRefGoogle Scholar
8Shew, B.Y. and Huang, J.L.: Mater. Sci. Eng. A 159, 127 (1992).CrossRefGoogle Scholar
9Choi, H.J., Cho, K.S. and Lee, J.G.: J. Am. Ceram. Soc. 80, 2681 (1997).CrossRefGoogle Scholar
10Lee, S.K., Lee, K.S., Lawn, B.R. and Kim, D.K.: J. Am. Ceram. Soc. 81, 2061 (1998).CrossRefGoogle Scholar
11Faber, K.T. and Evans, A.G.: Acta. Metall. 31, 565 (1983).CrossRefGoogle Scholar
12Evans, A.G. and Charles, E.A.: J. Am. Ceram. Soc. 59, 371 (1976).CrossRefGoogle Scholar
13Liu, C.C. and Huang, J.L.: Br. Ceram. Trans. 99, 149 (2000).CrossRefGoogle Scholar
14Ramulu, M.: Adv. Ceram. Mater. 3, 324 (1988).CrossRefGoogle Scholar
15Rak, Z.S. and Czechowski, J.: J. Eur. Ceram. Soc. 18, 373 (1998).CrossRefGoogle Scholar
16Childs, T.H.C. and Mimaroglu, A.: Wear 162–164, 890 (1993).CrossRefGoogle Scholar
17Skopp, A., Woydt, M. and Habig, K.H.: Wear 181–183, 571 (1995).Google Scholar
18Effner, U. and Woydt, M.: Wear 216, 123 (1998).CrossRefGoogle Scholar
19Imada, Y., Kanamura, K., Honda, F. and Nakajima, K.: J. Tribol. 114, 230 (1992).CrossRefGoogle Scholar
20Ravikiran, A. and Bai, B.N.P.: J. Am. Ceram. Soc. 78, 3025 (1995).CrossRefGoogle Scholar
21Vizintin, J., Kalin, M., Novak, S., Drazic, G., Ives, L.K. and Peterson, M.B.: Wear 192, 11 (1996).CrossRefGoogle Scholar
22Dogan, C.P. and Hawk, J.A.: Wear 250, 256 (2001).CrossRefGoogle Scholar
23Novak, S., Drazic, G., Kalin, M. and Vizintin, J.: Wear 225–229, 1276 (1999).CrossRefGoogle Scholar
24Cranmer, D.C.: J. Mater. Sci. 20, 2029 (1985).CrossRefGoogle Scholar
25Dong, X. and Jahanmir, S.: Wear 165, 169 (1993).CrossRefGoogle Scholar
26Gomes, J.R., Miranda, A.S., Silva, R.F. and Vieira, J.M.: J. Am. Ceram. Soc. 82, 953 (1999).CrossRefGoogle Scholar
27Wang, Y. and Hsu, S.M.: Wear 195, 112 (1996).CrossRefGoogle Scholar
28Meyers, M.A. and Chawla, K.K. in Mechanical Metallurgy Principles and Applications, edited by Kurtz, B., Soler, T., Krivanek, N., and Enterprises, E. (Prentice-Hall, Englewood Cliffs, NJ, 1984), pp. 284–288.Google Scholar
29Verhoeven, J.D.: Fundamentals of Physical Metallurgy (John Wiley & Sons, New York, 1975), pp. 459–464.Google Scholar
30Nagaoka, T., Yasuoka, M., Hirao, K. and Kanzaki, S.: J. Ceram. Soc. Jpn. 100, 617 (1992).CrossRefGoogle Scholar
31Sharma, V., Nasser, S.N. and Vecchio, K.S.: J. Am. Ceram. Soc. 81, 129 (1998).CrossRefGoogle Scholar
32Pezzotti, G., Okamoto, Y., Nishida, T. and Sakai, M.: Acta Metall. Mater. 43, 1323 (1995).CrossRefGoogle Scholar
33He, Y.J., Winnubst, A.J.A., Schipper, D.J., Bakker, P.M.V., Burggraaf, A.J. and Verweij, H.: Wear 184, 33 (1995).CrossRefGoogle Scholar
34Tuchinskiy, L., Veksler, E. and Loutfy, R.: Tribo. Trans. 43, 603 (2000).CrossRefGoogle Scholar