Hostname: page-component-586b7cd67f-dlnhk Total loading time: 0 Render date: 2024-11-24T16:38:11.623Z Has data issue: false hasContentIssue false
  • English
  • Français

The influence of the measurement parameters on the crushing strength of reticulated ceramic foams

Published online by Cambridge University Press:  16 May 2013

Claudia Voigt ,
Johannes Storm ,
Martin Abendroth ,
Christos G. Aneziris ,
Meinhard Kuna  and
Jana Hubálková
Claudia Voigt*
Affiliation:
Department of Ceramics, Glass and Construction Materials Technology, Technical University Bergakademie Freiberg, 09599 Freiberg, Germany
Johannes Storm
Affiliation:
Department for Mechanics and Fluid Dynamics, Technical University Bergakademie Freiberg, 09599 Freiberg, Germany
Martin Abendroth
Affiliation:
Department for Mechanics and Fluid Dynamics, Technical University Bergakademie Freiberg, 09599 Freiberg, Germany
Christos G. Aneziris
Affiliation:
Department of Ceramics, Glass and Construction Materials Technology, Technical University Bergakademie Freiberg, 09599 Freiberg, Germany
Meinhard Kuna
Affiliation:
Technical University Bergakademie Freiberg, Institute for Mechanics and Fluid Dynamics, 09599 Freiberg, Germany
Jana Hubálková
Affiliation:
Department of Ceramics, Glass and Construction Materials Technology, Technical University Bergakademie Freiberg, 09599 Freiberg, Germany
*
a)Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

The crushing strength or compression strength is a fundamental mechanical property for reticulated ceramic foams. There are essential influencing variables such as the rate of the applied load, the size of the applied load area, the sample size, and the strut homogeneity of the samples. In this work, the impact of the variation of the testing parameters on the crushing strength measurement was evaluated with the help of industrially produced ceramic foams made of Al2O3, ZrO2, SiC, and fused silica. The results indicate that the rate of the applied load has no significant influence on the crushing strength of the ceramic foams. Whereas the size of the applied load area and the sample size have an evident influence. The experimental results were compared with the minimum principal stress distribution calculated with FEM.

Type
Articles
Information
Journal of Materials Research , Volume 28 , Issue 17: Focus Issue: Advances in the Synthesis, Characterization, and Properties of Bulk Porous Materials , 14 September 2013 , pp. 2288 - 2299
Copyright
Copyright © Materials Research Society 2013 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

Shaped Insulating Refractory Products – Determination of Cold Crushing Strength. Standard DIN EN ISO 8895, 2006.Google Scholar
Methods of Test for Dense Shaped Refractory Products – Part 5: Determination of Cold Crushing Strength. Standard DIN EN 993–5, 1998.Google Scholar
Brezny, R. and Green, D.J.: Uniaxial strength behavior of brittle cellular materials. J. Am. Ceram. Soc. 76, 9 (1993).CrossRefGoogle Scholar
Wolf, S., Walther, H., Langer, P., and Stoyan, D.: Statistische Untersuchungen der Druckfestigkeit von Porenbeton – Größeneffekt und Umrechnungsfaktoren. Mauerwerk 12, 1 (2008).CrossRefGoogle Scholar
Oliveria, F.A.C., Dias, A., Vaz, M.F., and Fernandes, J.C.: Behavior of open-cell cordierite foams under compression. J. Eur. Ceram. Soc. 26, 169–186 (2006).Google Scholar
Dam, C.Q., Brezny, R., and Green, D.J.: Compressive behavior and deformation-mode map of an open cell alumina. J. Mater. Res. 5, 1 (1990).CrossRefGoogle Scholar
Emmel, M. and Aneziris, C.G.: Development of novel carbon bonded filter compositions for steel melt filtration. Ceram. Int. 38, 5165–5173 (2012).CrossRefGoogle Scholar
Colombo, P., Hellmann, J.R., and Shelleman, D.L.: Mechanical properties of silicon oxycarbide ceramic foams. J. Am. Ceram. Soc. 84, 10 (2001).CrossRefGoogle Scholar
Heness, G., Booth, N., and Ben-Nissan, B.: Does size matter? – The effect of volume on the compressive strength of open cell brittle ceramics. Adv. Mater. Res. 41–42, 221–226 (2008).CrossRefGoogle Scholar
Meille, S., Lombardi, M., Chevalier, J., and Montanaro, L.: Mechanical properties of porous ceramics in compression: On the transition between elastic, brittle, and cellular. J. Eur. Ceram. Soc. 32, 3959–3967 (2012).CrossRefGoogle Scholar
Acchar, W., Souza, F.B.M., Ramalho, E.G., and Torquato, W.L.: Mechanical characterization of cellular ceramics. Mater. Sci. Eng., A 513–514, 340–343 (2009).CrossRefGoogle Scholar
BDG-Richtlinie, VDG Merkblatt P100, Keramische Filter in Schaumstruktur – Schaumkeramikfilter für Eisen- und Stahlguss, September 2012.Google Scholar
Orenstein, R.M. and Green, D.J.: Thermal shock behavior of open-cell ceramic foams. J. Am. Ceram. Soc. 75, 7 (1992).CrossRefGoogle Scholar
Gibson, L.J. and Ashby, M.F.: Cellular Solids: Structure and Properties, 2nd ed. (Cambridge University Press, Cambridge, UK, 1997).CrossRefGoogle Scholar
Voigt, C., Jäckel, E., Aneziris, C.G., and Hubálková, J.: Investigations of reticulated porous alumina foam ceramics based on different coating techniques with the aid of µCT and statistical characteristics. Ceram. Int. 39, 3 (2013).CrossRefGoogle Scholar
Montgomery, D.C., Runger, C.G., and Faris Hubele, N.: Engineering Statistics. 4th ed. (John Wiley & Sons, Inc., Hoboken, NJ, 2007).Google Scholar
Salmang, H. and Scholze, H.: Keramik, 7th ed. (Springer-Verlag Berlin Heidelberg, Germany, 2007).Google Scholar
Ballani, F., Stoyan, D., and Wolf, S.: On two damage accumulation models and their size effects. J. Appl. Probab. 44, 99–114 (2007).CrossRefGoogle Scholar
Brezny, R. and Green, J.: The effect of cell size on the mechanical behavior of cellular materials. Acta Metall. Mater. 38, 12 (1990).CrossRefGoogle Scholar