Hostname: page-component-586b7cd67f-vdxz6 Total loading time: 0 Render date: 2024-11-28T04:04:40.473Z Has data issue: false hasContentIssue false
  • English
  • Français

Influence of sample thickness and concentration of Ce dopant on the optical properties of YAG:Ce ceramic phosphors for white LEDs

Published online by Cambridge University Press:  08 September 2014

Katja Waetzig ,
Michael Kunzer  and
Isabel Kinski
Katja Waetzig*
Affiliation:
Fraunhofer Institute for Ceramic Technologies and Systems (IKTS),Department of Precursor-Derived Ceramics and Composites, Dresden 01277, Germany
Michael Kunzer
Affiliation:
Fraunhofer Institute for Applied Solid State Physics (IAF), Business Unit Semiconductor Lasers and LEDs, Freiburg D-79108, Germany
Isabel Kinski
Affiliation:
Fraunhofer Institute for Ceramic Technologies and Systems (IKTS), Department of Precursor-Derived Ceramics and Composites, Dresden 01277, Germany
*
a)Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

Translucent, polycrystalline YAG:Ce disks with 0.1, 0.5, and 1 mol% concentrations of cerium as well as different resulting thicknesses of 0.5 and 0.8 mm were prepared by reaction sintering of yttria, alumina, and cerium oxide under vacuum at a temperature of 1800 °C. The obtained samples displayed a microstructure with a Y3Al5O12 main phase interrupted by an intended scattering phase of alumina. Furthermore, the total forward transmittance was between 75 and 78% with the typical absorption bands of cerium at wavelengths of 330 and 460 nm. Phosphor conversion light-emitting diodes (LEDs) with 0.88 W power dissipation have been prepared from these YAG:Ce ceramic disks as converters and blue 455 nm LED chips for excitation. Their color coordinates in the CIE (Commission Internationale de l’Eclairage) diagram determined by spectral photometry depend on the concentration of the Ce dopant and the ceramic converter thickness. The highest luminous flux of 276 lm with an efficiency of 76.6 lm/W was measured for a converter with 0.5 mol% dopant concentration and 0.8 mm thickness emitting a yellowish white light.

Keywords

ceramicopticaltransparentphosphorLED
Type
Articles
Information
Journal of Materials Research , Volume 29 , Issue 19: Focus Issue: Optical Ceramics Science , 14 October 2014 , pp. 2318 - 2324
Copyright
Copyright © Materials Research Society 2014 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

Holonyak, N. Jr. and Bevacqua, S.F.: Coherent (visible) light emission from Ga(As1−xPx) junctions. Appl. Phys. Lett. 1(4), 82 (1962).CrossRefGoogle Scholar
Nakamura, S., Fasol, G., and Pearton, S.J.: The Blue Laser Diode: The Complete Story, 2nd ed.; Springer: Berlin, Germany, 2000; p. 2.Google Scholar
Schlotter, P., Schmidt, R., and Schneider, J.: Luminescence or blue light emitting diodes. Appl. Phys. A 64, 417 (1997).Google Scholar
Nishiura, S., Tanabe, S., Fujioka, K., Fujimoto, Y., and Nakatsuka, M.: Preparation and optical properties of transparent Ce:YAG ceramics for high power white LED. IOP Conf. Ser.: Mater. Sci. Eng. 1, 012031 (2009).CrossRefGoogle Scholar
Bechtel, H., Schmidt, P.J., Tücks, A., Heidemann, M., Chamberlin, D., Mueller-Mach, R., Mueller, G.O., and Shchekin, O.: Fully phosphor-converted LEDs with Lumiramic phosphor technology. In Proceedings of SPIE, Tenth International Conference on Solid State Lighting, Vol. 7784, 2010; p. 77840W.Google Scholar
Ikesue, A., Furusato, I., and Kamata, K.: Fabrication of polycrystalline, transparent YAG ceramics by a solid-state reaction method. J. Am. Ceram. Soc. 78(11), 225 (1995).Google Scholar
Ikesue, A. and Aung, Y.L.: Synthesis and performance of advanced ceramic lasers. J. Am. Ceram. Soc. 89(6), 1936 (2006).Google Scholar
Krames, M.R., Shchekin, O.B., Mueller-Mach, R., Mueller, G.O., Zhou, L., Harbers, G., and Craford, M.G.: Status and future of high-power light-emitting diodes for solid-state lighting. J. Disp. Technol. 3(2), 160 (2007).Google Scholar
Raukas, M., Kelso, J., Zheng, Y., Bergenek, K., Eisert, D., Linkov, A., and Jermann, F.: Ceramic phosphors for light conversion in LEDs. ECS J. Solid State Sci. Technol. 2(2), R3168 (2013).Google Scholar
Nishiura, S., Tanabe, S., Fujioka, K., and Fujimoto, Y.: Properties of transparent Ce:YAG ceramic phosphors for white LED. Opt. Mater. 33, 688 (2011).Google Scholar
BrukerAXS and DIFFRACPlus TOPAS: TOPAS 4.2 User Manual (Bruker-AXS GmbH, Karlsruhe, Germany, 2008).Google Scholar
Krell, A., Hutzler, T., and Klimke, J.: Transmission physics and consequences for materials selection, manufacturing, and applications. J. Eur. Ceram. Soc. 29, 207 (2009).Google Scholar