Hostname: page-component-78c5997874-ndw9j Total loading time: 0 Render date: 2024-11-07T21:18:09.573Z Has data issue: false hasContentIssue false
  • English
  • Français

Indentation Response of Molybdenum Disilicide

Published online by Cambridge University Press:  31 January 2011

A. Newman ,
T. Jewett ,
S. Sampath ,
C. Berndt  and
H. Herman
A. Newman
Affiliation:
Department of Materials Science and Engineering, Stony Brook, State University of New York, Stony Brook, New York 11794-2275
T. Jewett
Affiliation:
Department of Materials Science and Engineering, Stony Brook, State University of New York, Stony Brook, New York 11794-2275
S. Sampath
Affiliation:
Department of Materials Science and Engineering, Stony Brook, State University of New York, Stony Brook, New York 11794-2275
C. Berndt
Affiliation:
Department of Materials Science and Engineering, Stony Brook, State University of New York, Stony Brook, New York 11794-2275
H. Herman
Affiliation:
Department of Materials Science and Engineering, Stony Brook, State University of New York, Stony Brook, New York 11794-2275
Get access

Abstract

The influence of microstructure on the indentation cracking behavior of molybdenum disilicide (MoSi2) has been examined. The indentation response of samples produced by various methods has been measured to examine the elastic/plastic nature, hardness, and fracture toughness. Fracture toughness comparisons were made by measuring indentation crack lengths, observing the elastic/plastic indentation response, and quantifying the differences in the indentation cracking behavior. Further information was gained by monitoring the acoustic activity during indentation for selected specimens. It has been observed that the fine grain size and the dispersion of the silica phase promote microcracking and crack deflection.

Type
Articles
Information
Journal of Materials Research , Volume 13 , Issue 9 , September 1998 , pp. 2662 - 2671
Copyright
Copyright © Materials Research Society 1998

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1.Shah, D. M., Berczik, D., Anton, D. L., and Hecht, R., Mater. Sci. Eng. A155, 45–58 (1992).CrossRefGoogle Scholar
2.Vasudevan, A. K. and Petrovic, J. J., Mater. Sci. Eng. A155, 1–18 (1992).CrossRefGoogle Scholar
3.Fitzer, E. and Remmale, W., in Proc. 5th Int. Conf. on Composite Materials, ICCM-V (Am. Inst. Min. Engrs., Philadelphia, PA, 1985), pp. 143–156.Google Scholar
4.Wade, R. K. and Petrovic, J. J., J. Am. Ceram. Soc. 75 (6), 1682–1684 (1992).CrossRefGoogle Scholar
5.Hardwick, D. A., Martin, P. L., and Moores, R. J., Scripta Metall. Mater. 27, 391–394 (1992).CrossRefGoogle Scholar
6.Deevi, S. C., J. Mater. Sci. 26, 3343–3353 (1991).CrossRefGoogle Scholar
7.Sampath, S. and Herman, H., in High Temperature Silicides and Refractory Alloys, edited by Briant, C. L., Petrovic, J. J., Bewlay, B. P., Vasudevan, A. K., and Lipsitt, H. A. (Mater. Res. Soc. Symp. Proc. 322, Pittsburgh, PA, 1994), pp. 71–80.Google Scholar
8.Aikin, R. M., Jr., Scripta Metall. Mater. 26, 1025–1030 (1992).CrossRefGoogle Scholar
9.Hardwick, D. A., Martin, P. L., and Moores, R. J., Scripta Metall. Mater. 27, 391–394 (1992).CrossRefGoogle Scholar
10.Cotton, J. D., Kim, Y. S., and Kaufman, M. J., Mater. Sci. Eng. A144, 287–291 (1991).CrossRefGoogle Scholar
11.Silva, A. Costa e and Kaufman, M. J., Met. Trans. A 25A (1), 5–15 (1994).CrossRefGoogle Scholar
12.Chou, T. C. and Nieh, T. G., J. Mater. Res. 8, 214–226 (1993).CrossRefGoogle Scholar
13.Maloy, S., Heuer, A. H., Lewandowski, J., and Petrovic, J., J. Am. Ceram. Soc. 74 (10), 2704–2706 (1991).CrossRefGoogle Scholar
14.Vahldiek, F. W. and Mersol, S. A., J. Less-Comm. Met. 15, 165–176 (1968).CrossRefGoogle Scholar
15.Boldt, P. H., Embury, J. D., and Weatherly, G. C., Mater. Sci. Eng. A155, 251–258 (1992).CrossRefGoogle Scholar
16.Ito, K., Inui, H., Shirai, Y., and Yamaguchi, M., Philos. Mag. A 72 (4), 1075–1097 (1995).CrossRefGoogle Scholar
17.Hebsur, M., in Intermetallic Matrix Composites III, edited by Graves, J. A., Bowman, R. R., and Lewandowski, J. J. (Mater. Res. Soc. Symp. Proc. 350, Pittsburgh, PA, 1994), pp. 77–182.Google Scholar
18.Petrovic, J. J. and Honnell, R. E., J. Mater. Sci. Lett. 9, 1083–1084 (1990).CrossRefGoogle Scholar
19.Aikin, R. M., Jr., in Ceram. Eng. Sci. Proc., 15th Annual Conference on Composites and Advanced Ceramic Materials, edited by Wachtman, J. B. (American Ceramic Society, Westerville, OH, 1991), Vol. 12, No. 9–10, pp. 1643–1655.Google Scholar
20.Petrovic, J. J., Bhattacharya, A. K., Honnell, R. E., Mitchell, T. E., K.Wade, R., and McClellan, K. J., Mater. Sci. Eng. A155, 259–266 (1992).CrossRefGoogle Scholar
21.Gibala, R., Chang, H., and Czarnik, C. M., in High Temperature Silicides and Refractory Alloys, edited by Briant, C. L., Petrovic, J. J., Bewlay, B. P., Vasudevan, A. K., and Lipsitt, H. A. (Mater. Res. Soc. Symp. Proc. 322, Pittsburgh, PA, 1994), pp. 175–184.Google Scholar
22.Baker, I. and Munroe, P. R., J. Met. 40 (2), 28–31 (1988).Google Scholar
23.Darolia, R., Lahrman, D., and Field, R., Scripta Metall. et Mater. 26, 1007–1012 (1992).CrossRefGoogle Scholar
24.Yamaguchi, M. and Umakoshi, Y., Prog. Met. Sci. 34, 22,118 (1990).Google Scholar
25.Umakoshi, Y., Hirano, T., Sakagami, T., and Yamane, T., in High Temperature Aluminides and Intermetallics, edited by Whang, S., Liu, C., Pope, D., and Stiegler, J. (TMS, Warrendale, PA, 1990), pp. 111–129.Google Scholar
26.Stergiou, A. and Tsakiropoulos, P., in High Temperature Ordered Alloys VI, edited by Horton, J. A., Baker, I., Hanada, S., Noebe, R. D., and Schwartz, D. S. (Mater. Res. Soc. Symp. Proc. 364, Pittsburgh, PA, 1995), pp. 911–916.Google Scholar
27.Chin, S., Anton, D. L., and Giamei, A. F., in High Temperature Silicides and Refractory Alloys, edited by Briant, C. L., Petrovic, J. J., Bewlay, B. P., Vasudevan, A. K., Lipsitt, H. A. (Mater. Res. Soc. Symp. Proc. 322, Pittsburgh, PA, 1994), pp. 423–429.Google Scholar
28.Davidson, D. L. and Bose, A., in High Temperature Silicides and Refractory Alloys, edited by Briant, C. L., Petrovic, J. J., Bewlay, B. P., Vasudevan, A. K., and Lipsitt, H. A. (Mater. Res. Soc. Symp. Proc. 322, Pittsburgh, PA, 1994), pp. 431–436.Google Scholar
29.Marshall, D. B., Noma, T., and Evans, A. G., J. Am. Ceram. Soc. 65 (10), C175–176 (1982).Google Scholar
30.Oliver, W. C. and Pharr, G. M., J. Mater. Res. 7, 1565–1570 (1992).CrossRefGoogle Scholar
31.Anstis, G. R., Chantikul, P., Lawn, B. R., and Marshall, D. B., J. Am. Ceram. Soc. 64 (09), 533–538 (1981).CrossRefGoogle Scholar
32.Newman, A., Sampath, S., and Herman, H., in Processing and Design Issues in High Temperature Materials, edited by Stoloff, N. S. and Jones, R. H. (The Minerals, Metals, and Materials Society, Warrendale, PA, 1997), pp. 403–412.Google Scholar
33.Petrovic, J. J. and Honnell, R. E., J. Mater. Sci. 25, 4453–4456 (1990).CrossRefGoogle Scholar
34.Tiwari, R., Herman, H., and Sampath, S., Mater. Sci. Eng. A155, 95–100 (1992).CrossRefGoogle Scholar
35.Bhattacharya, A. K. and Petrovic, J. J., J. Am. Ceram. Soc. 74 (10), 2700–2703 (1991).CrossRefGoogle Scholar
36.Bhaduri, S. B. and Radhakrishnan, R., in Advances in Powder Metallurgy & Particulate Materials, Vol. 9, edited by Capus, J. M. and German, R. M. (Particulate Materials and Processes, Vol. 9, American Powder Metallurgy Institute, Princeton, NJ, 1992), pp. 369–379.Google Scholar
37.Castro, R. G., Smith, R. W., Rollett, A. D., and Stanek, P. W., Scripta Metall. et Mater. 26, 207–212 (1992).CrossRefGoogle Scholar
38.Wade, R. K. and Petrovic, J. J., J. Am. Ceram. Soc. 75 (11), 3160–3162 (1992).CrossRefGoogle Scholar
39.Jeng, Y. L., Wolfenstine, J., and Lavernia, E. J., Scripta Metall. et Mater. 28, 453–458 (1993).CrossRefGoogle Scholar
40.Jayashankar, S., Riddle, S. E., and Kaufman, M. J., in High Temperature Silicides and Refractory Alloys, edited by Briant, C. L., Petrovic, J. J., Bewlay, B. P., Vasudevan, A. K., and Lipsitt, H. A. (Mater. Res. Soc. Symp. Proc. 322, Pittsburgh, PA, 1994), pp. 33–40.Google Scholar
41.Faber, K. T. and Evans, A. G., J. Am. Ceram. Soc. 66, C94–96 (1983).CrossRefGoogle Scholar
42.Scruby, C. B., Jones, C., Titchmarsh, J. M., and Wadley, H. N. G., Metal Science 15, 241–261 (1981).CrossRefGoogle Scholar
43.Evans, A. G. and Linzer, M., J. Am. Ceram. Soc. 56, 575–580 (1973).CrossRefGoogle Scholar
44.Schulson, E. M., Res. Mech. Lett. 1, 111 (1981).Google Scholar
45.Gaydosh, D. J., Jech, R. W., and Titran, R. H., J. Mat. Sci. Lett. 4, 138 (1985).CrossRefGoogle Scholar