Hostname: page-component-586b7cd67f-dlnhk Total loading time: 0 Render date: 2024-11-28T09:03:35.676Z Has data issue: false hasContentIssue false
  • English
  • Français

In situ synthesis of paper-derived Ti3SiC2

Published online by Cambridge University Press:  02 May 2017

Hannes Lorenz ,
Johannes Thäter ,
Mylena Mayara Matias Carrijo ,
Carlos R. Rambo ,
Peter Greil  and
Nahum Travitzky
Hannes Lorenz*
Affiliation:
Department of Material Science, Institute of Glass and Ceramics, University of Erlangen-Nuremberg, Erlangen 91058, Germany
Johannes Thäter
Affiliation:
Department of Material Science, Institute of Glass and Ceramics, University of Erlangen-Nuremberg, Erlangen 91058, Germany
Mylena Mayara Matias Carrijo
Affiliation:
Department of Material Science, Institute of Glass and Ceramics, University of Erlangen-Nuremberg, Erlangen 91058, Germany; and Graduate Program on Materials Science and Engineering, Federal University of Santa Catarina (UFSC), Florianópolis 88040-900, SC, Brazil
Carlos R. Rambo
Affiliation:
Graduate Program on Materials Science and Engineering, Federal University of Santa Catarina (UFSC), Florianópolis 88040-900, SC, Brazil; and Department of Electrical and Electronic Engineering, Federal University of Santa Catarina (UFSC), Florianópolis 88040-900, SC, Brazil
Peter Greil
Affiliation:
Department of Material Science, Institute of Glass and Ceramics, University of Erlangen-Nuremberg, Erlangen 91058, Germany
Nahum Travitzky
Affiliation:
Department of Material Science, Institute of Glass and Ceramics, University of Erlangen-Nuremberg, Erlangen 91058, Germany
*
a)Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

A novel approach based on the preceramic paper method was used for the fabrication of Ti3SiC2-based material. Elemental powders of Ti, TiC, Si, C, and organic additives were used as starting materials. The Rapid Köthen process was used to fabricate the preceramic papers. The high-loaded green body of preceramic papers was heat-treated up to varying temperatures of 1300, 1400, 1500, and 1600 °C for 1 h in an Ar atmosphere. By using an excess amount of Si powder in the basic composition, the amount of Ti3SiC2 in the sintered specimen could be increased while the amount of TiC could be reduced. X-ray analysis showed that the paper-derived sample with the basic powder composition 3Ti/3TiC/3Si/C was a single phase within the resolution limit of the instrument used. The high purity of Ti3SiC2 can be explained by the partial formation of amorphous C which could not be detected by X-ray diffraction. Scanning electron microscopy analysis of fracture surfaces showed the characteristic lamellar structure of the paper-derived MAX phase.

Keywords

ceramicmicrostructurereactivity
Type
Invited Articles
Information
Journal of Materials Research , Volume 32 , Issue 17: Focus Issue: Achieving Superior Ceramics and Coating Properties through Innovative Processing , 14 September 2017 , pp. 3409 - 3414
Check for updates
Copyright
Copyright © Materials Research Society 2017 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

Footnotes

b)

This author was an editor of this journal during the review and decision stage. For the JMR policy on review and publication of manuscripts authored by editors, please refer to http://www.mrs.org/editor-manuscripts/.

Contributing Editor: Xiaowei Yin

References

REFERENCES

Gao, N.F., Li, J.T., Zhang, D., and Miyamoto, Y.: Rapid synthesis of dense Ti3SiC2 by spark plasma sintering. J. Eur. Ceram. Soc. 22, 2365 (2002).CrossRefGoogle Scholar
El-Raghy, T. and Barsoum, M.W.: Diffusion kinectics of the carburization and silicidation of Ti3SiC2 . J. Appl. Phys. 83, 112 (1998).CrossRefGoogle Scholar
El-Raghy, T. and Barsoum, M.W.: Synthesis and characterization of a remarkable ceramic: Ti3SiC2 . J. Am. Ceram. Soc. 79, 1953 (1996).Google Scholar
Lis, J., Pampuch, R., Rudnik, T., and Wegrzyn, Z.: Reaction sintering phenomena of self-propagating high-temperature synthesis-derived ceramic powders in the Ti–Si–C system. Solid State Ionics 101–103, 59 (1997).Google Scholar
El-Raghy, T. and Barsoum, M.W.: Processing and mechanical properties of Ti3SiC2: II, effect of grain size and deformation temperature. J. Am. Ceram. Soc. 82, 2855 (1999).CrossRefGoogle Scholar
Tong, X., Okano, T., Iseki, T., and Yano, T.: Synthesis and high temperature mechanical properties of Ti3SiC2/SiC composite. J. Mater. Sci. 30, 3087 (1995).Google Scholar
Sun, W., Dcosta, D.J., Lin, F., and El-Raghy, T.: Freeform fabrication of Ti3SiC2. Powder based structures part I: Integrated fabrication process. J. Mater. Process. Technol. 127, 343 (2002).Google Scholar
Carrijo, M.M.M., Lorenz, H., Filbert-Demut, I., Barra, G.M.O., Hotza, D., Yin, X., Greil, P., and Travitzky, N.: Fabrication of Ti3SiC2-based composites via three-dimensional printing: Influence of processing on the final properties. Ceram. Int. 42, 9557 (2016).CrossRefGoogle Scholar
El-Raghy, T. and Barsoum, M.W.: Processing and mechanical properties of Ti3SiC2: I, reaction path and microstructure evolution. J. Am. Ceram. Soc. 82, 2849 (1999).Google Scholar
Goto, T. and Hirai, T.: Chemically vapor deposited Ti3SiC2 . Mater. Res. Bull. 22, 1195 (1987).Google Scholar
Pickering, E., Lackey, W.J., and Crain, S.: CVD of Ti3SiC2 . Chem. Vapor Deposition 6, 289 (2000).Google Scholar
Racault, C., Langlais, F., and Bernard, C.: On the chemical vapor deposition of Ti3SiC2 from TiCl4–SiCl4–CH4–H2 gas mixtures. J. Mater. Sci. 29, 5023 (1994).CrossRefGoogle Scholar
Zhou, Y., Sun, Z., Chen, S., and Zhang, Y.: In situ hot pressing/solid-liquid reaction synthesis of dense titanium silicon carbide bulk ceramics. Mater. Res. Innovations 2, 142 (1998).Google Scholar
Yongming, L., Wei, P., Shuqin, L., Jian, C., Ruigang, W., and Jianqiang, L.: Synthesis of high-purity Ti3SiC2 polycrystals by hot-pressing of the elemental powders. Mater. Lett. 52, 245 (2002).CrossRefGoogle Scholar
Li, J.F. and Matsuki, T.: Combustion reaction during mechanical alloying synthesis of Ti3SiC2 ceramics from 3Ti/Si/2C powder mixture. J. Am. Ceram. Soc. 88, 1318 (2005).Google Scholar
Li, S.B. and Zhai, H.X.: Synthesis and reaction mechanism of Ti3SiC2 by mechanical alloying of elemental Ti, Si and C powders. J. Am. Ceram. Soc. 88, 2092 (2005).Google Scholar
Li, J.F., Matsuki, T., and Watanabe, R.: Fabrication of highly dense Ti3SiC2 ceramics by pressureless sintering of mechanically alloyed elemental powders. J. Mater. Sci. 38, 2661 (2003).Google Scholar
Racault, C.: Solid-state synthesis and characterization of the ternary phase Ti3SiC2 . J. Mater. Sci. 29, 3384 (1994).Google Scholar
Emmerlich, J., Högberg, H., Sasvári, S., Persson, P.O.A., Hultman, L., Palmquist, J-P., Jansson, U., Molina-Aldareguia, J.M., and Czigány, Z.: Growth of Ti3SiC2 thin films by elemental target magnetron sputtering. J. Appl. Phys. 96, 4817 (2004).Google Scholar
Arunajatesan, S. and Carim, A.H.: Synthesis of titanium silicon carbide. J. Am. Ceram. Soc. 78, 667 (1995).Google Scholar
Schultheiß, J., Dermeik, B., Filbert-Demut, I., Hock, N., Yin, X., Greil, P., and Travitzky, N.: Processing and characterization of paper-derived Ti3SiC2 based ceramic. Ceram. Int. 41, 12595 (2015).Google Scholar
Weisensel, L., Travitzky, N., Sieber, H., and Greil, P.: Laminated objective manufacturing (LOM) of Si–SiC composite. Adv. Eng. Mater. 6, 899 (2004).Google Scholar
Windsheimer, H., Travitzky, N., Hofenauer, A., and Greil, P.: Laminated objective manufacturing of preceramic-paper-derived Si–SiC composites. Adv. Mater. 19, 4515 (2007).Google Scholar
Travitzky, N., Windsheimer, H., Fey, T., and Greil, P.: Preceramic paper-derived ceramics. J. Am. Ceram. Soc. 91, 3477 (2008).Google Scholar
Gutbrod, B., Haas, D., Travitzky, N., and Greil, P.: Preceramic paper derived alumina/zirconia ceramics. Adv. Eng. Mater. 13, 494 (2011).CrossRefGoogle Scholar
Stares, S.L., Kirilenko, A., Fredel, M.C., Greil, P., Wondraczek, L., and Travitzky, N.: Paper-derived bioactive glass tape. Adv. Eng. Mater. 15, 230 (2013).Google Scholar
Lorenz, H., Bonet, A., Ayrikyan, A., Greil, P., and Travitzky, N.: Paper-derived bioactive ceramics for complex shape bone implants. Adv. Biomater. Dev. Med. 2, 88 (2015).Google Scholar
Schlordt, T., Dermeik, B., Beil, V., Freihart, M., Hofenauer, A., Travitzky, N., and Greil, P.: Influence of calendering on the properties of paper-derived alumina ceramics. Ceram. Int. 40, 4917 (2014).Google Scholar
Dasgupta, S. and Das, S.K.: Paper pulp waste—a new source of raw material for the synthesis of a porous ceramic composite. B. Mater. Sci. 25, 381 (2002).Google Scholar
Park, C-S., Zheng, F., Salamone, S., and Bordia, R.K.: Processing of composites in the Ti–Si–C system. J. Mater. Sci. 36, 3313 (2001).Google Scholar
Radhakrishnan, R., Williams, J.J., and Akinc, M.: Synthesis and high-temperature stability of Ti3SiC2 . J. Alloys Compd. 285, 85 (1999).Google Scholar
Sato, F., Li, J-F., and Watanabe, R.: Reaction synthesis of Ti3SiC2 from mixture of elemental powders. Mater. T. JIM 41, 605 (2000).Google Scholar
Zhang, J., Wang, L., Jiang, W., and Chen, L.: Reaction path and microstructures of Ti3SiC2/Si composite by spark plasma sintering. Scr. Mater. 56, 241 (2007).Google Scholar