Hostname: page-component-586b7cd67f-t7fkt Total loading time: 0 Render date: 2024-11-24T15:50:58.776Z Has data issue: false hasContentIssue false
  • English
  • Français

In situ monitoring of cracking behaviors of plasma-sprayed coatings by the laser acoustic emission technique

Published online by Cambridge University Press:  31 January 2011

Koichi Taniguchi ,
Manabu Enoki ,
Makoto Watanabe ,
Seiji Kuroda  and
Kaita Ito
Koichi Taniguchi
Affiliation:
Department of Materials Engineering, The University of Tokyo, Tokyo 153-8902, Japan
Manabu Enoki*
Affiliation:
Department of Materials Engineering, The University of Tokyo, Tokyo 153-8902, Japan
Seiji Kuroda
Affiliation:
Hybrid Materials Center, National Institute for Materials Science, Tsukuba, Ibaraki 305-0044, Japan
Kaita Ito
Affiliation:
Department of Materials Engineering, The University of Tokyo, Tokyo 153-8902, Japan; and Hybrid Materials Center, National Institute for Materials Science, Tsukuba, Ibaraki 305-0044, Japan
*
a) Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

Multichannel acoustic emission (AE) measurements by four laser interferometers were developed and applied during a plasma-spray coating process that is known as being a high-temperature process and an extremely noisy environment in both mechanical and electrical domains. The AE signals could be successfully detected during the cooling period after the deposition, and it was clearly indicated that a higher preheating temperature resulted in the improvement of bonding between splats and/or at the interface of the coating and the substrate. The maximum principal stress generated during the deposition process was calculated by the transient heat and stress analysis and the obtained AE events. The critical stress for crack initiation of the alumina coating on a steel substrate with an NiCr bond coat layer was estimated as 30∼45 MPa. The developed techniques were shown to be a potential tool for in situ monitoring of the thermal spray process, by which an increase in the reliability of thermal spray coatings can be expected.

Keywords

Acoustic emissionCoatingSpray deposition
Type
Articles
Information
Journal of Materials Research , Volume 24 , Issue 10 , October 2009 , pp. 3182 - 3189
Copyright
Copyright © Materials Research Society 2009

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1.Lima, R.S., Kruger, S.E., Lamouche, G., and Marple, B.R.: Elasticmodulus measurements via laser-ultrasonic and Knoop indentation techniques in thermally sprayed coatings. J. Therm. Spray Technol. 14, 52 (2005).CrossRefGoogle Scholar
2.Roge, B., Fahr, A., Giguere, J.S.R., and McRae, K.I.: Nondestructive measurement of porosity in thermal-barrier coatings. J. Therm. Spray Technol. 12, 530 (2003).CrossRefGoogle Scholar
3.Fahr, A., Roge, B., and Thornton, J.: Detection of thermally grown oxides in thermal-barrier coatings by nondestructive evaluation. J. Therm. Spray Technol. 15, 46 (2006).CrossRefGoogle Scholar
4.Fabbri, L. and Oksanen, M.: Characterization of plasma-sprayed coatings using nondestructive evaluation techniques: Roundrobin test results (Reprinted from Journal of the British Institute of Non-Destructive Testing, vol. 39, 1997). J. Therm. Spray Technol. 8, 263 (1999).CrossRefGoogle Scholar
5.Allen, A.J., Ilavsky, J., Long, G.G., Wallace, J.S., Berndt, C.C., and Herman, H.: Microstructural characterization of yttria-stabilized zirconia plasma-sprayed deposits using multiple small-angle neutron scattering. Acta Mater. 49, 1661 (2001).CrossRefGoogle Scholar
6.Wang, Z., Kulkarni, A., Deshpande, S., Nakamura, T., and Herman, H.: Effects of pores and interfaces on effective properties of plasma sprayed zirconia coatings. Acta Mater. 51, 5319 (2003).CrossRefGoogle Scholar
7.Kulkarni, A., Goland, A., Herman, H., Allen, A.J., Dobbins, T., DeCarlo, F., Ilavsky, J., Long, G.G., Fang, S., and Lawton, P.: Advanced neutron and x-ray techniques for insights into the microstructure of EB-PVD thermal-barrier coatings. Mater. Sci. Eng., A 426, 43 (2006).CrossRefGoogle Scholar
8.Kuroda, S., Fukushima, T., and Kitahara, S.: Simultaneous measurement of coating thickness and deposition stress during thermal spraying. Thin Solid Films 164, 157 (1988).CrossRefGoogle Scholar
9.Kuroda, S. and Clyne, T.W.: The quenching stress in thermally sprayed coatings. Thin Solid Films 200, 49 (1991).CrossRefGoogle Scholar
10.Matejicek, J. and Sampath, S.: In situ measurement of residual stresses and elastic moduli in thermal sprayed coatings: Part 1: Apparatus and analysis. Acta Mater. 51, 863 (2003).CrossRefGoogle Scholar
11.Matejicek, J., Sampath, S., Gilmore, D., and Neiser, R.: In situ measurement of residual stresses and elastic moduli in thermal sprayed coatings: Part 2: Processing effects on properties of Mo coatings. Acta Mater. 51, 873 (2003).CrossRefGoogle Scholar
12.Kishi, T. and Ohira, T.: Dynamic crack-growth during pop-in fracture in 7075 aluminum-alloy. Trans. Japan Inst. Metals 24, 255 (1983).CrossRefGoogle Scholar
13.Ohira, T. and Kishi, T.: Effect of iron content on fracture-toughness and cracking processes in high-strength Al-Zn-Mg-Cu alloy. Mater. Sci. Eng. 78, 9 (1986).CrossRefGoogle Scholar
14.Enoki, M. and Kishi, T.: Theory and analysis of deformation moment tensor due to microcracking. Int. J. Fract. 38, 295 (1988).CrossRefGoogle Scholar
15.Watanabe, M., Enoki, M., and Kishi, T.: Evaluation of microfracture location at elevated temperature by four-channel AE measurements using laser interferometer. J. Mater. Sci. Lett. 22, 1091 (2003).CrossRefGoogle Scholar
16.Watanabe, M., Enoki, M., and Kishi, T.: Fracture behavior of ceramic coatings during thermal cycling evaluated by acoustic emission method using laser interferometers. Mater. Sci. Eng., A 359, 368 (2003).CrossRefGoogle Scholar
17.Nishinoiri, S., Enoki, M., and Tomita, K.: In situ monitoring of microfracture during plasma-spray coating by laser AE technique. Sci. Technol. Adv. Mater. 4, 623 (2003).CrossRefGoogle Scholar
18.Liu, Y., Nakamura, T., Srinivasan, V., Vaidya, A., Gouldstone, A., and Sampath, S.: Non-linear elastic properties of plasma-sprayed zirconia coatings and associated relationships with processing conditions. Acta Mater. 55, 4667 (2007).CrossRefGoogle Scholar
19.Nakamura, T. and Liu, Y.J.: Determination of nonlinear properties of thermal sprayed ceramic coatings via inverse analysis. Int. J. Solids Struct. 44, 1990 (2007).CrossRefGoogle Scholar
20. JSME: Heat Transfer Engineering Handbook (The Japan Society of Mechanical Engineering, Tokyo, Japan, 1959).Google Scholar
21.Erdogan, F.: Fracture-mechanics of functionally graded materials. Compos. Eng. 5, 753 (1995).CrossRefGoogle Scholar
22.Mellali, M., Fauchais, P., and Grimaud, A.: Influence of substrate roughness and temperature on the adhesion/cohesion of alumina coatings. Surf. Coat. Technol. 81, 275 (1996).CrossRefGoogle Scholar
23.Irisawa, T. and Matsumoto, H.: Thermal shock resistance and adhesion strength of plasma-sprayed alumina coating on cast iron. Thin Solid Films 509, 141 (2006).CrossRefGoogle Scholar
24.Hasui, J.: Youshakougaku (Sanpo Publications, Tokyo, Japan, 1996).Google Scholar