Hostname: page-component-586b7cd67f-r5fsc Total loading time: 0 Render date: 2024-11-28T13:18:25.216Z Has data issue: false hasContentIssue false
  • English
  • Français

Gradient nano microstructure and its formation mechanism in pure titanium produced by surface rolling treatment

Published online by Cambridge University Press:  24 February 2014

Qi Wang ,
Yanfei Yin ,
Qiaoyan Sun ,
Lin Xiao  and
Jun Sun
Qi Wang
Affiliation:
State Key Laboratory for Mechanical Behavior of Materials, Xi’an Jiaotong University, Xi’an, Shaanxi 710049, People’s Republic of China
Yanfei Yin
Affiliation:
State Key Laboratory for Mechanical Behavior of Materials, Xi’an Jiaotong University, Xi’an, Shaanxi 710049, People’s Republic of China
Qiaoyan Sun
Affiliation:
State Key Laboratory for Mechanical Behavior of Materials, Xi’an Jiaotong University, Xi’an, Shaanxi 710049, People’s Republic of China
Lin Xiao*
Affiliation:
State Key Laboratory for Mechanical Behavior of Materials, Xi’an Jiaotong University, Xi’an, Shaanxi 710049, People’s Republic of China
Jun Sun
Affiliation:
State Key Laboratory for Mechanical Behavior of Materials, Xi’an Jiaotong University, Xi’an, Shaanxi 710049, People’s Republic of China
*
a)Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

A large depth of 800 μm gradient microstructure was produced in pure titanium (Ti) by means of surface rolling treatment (SRT). The microstructural characteristics with different depths from the top surface were analyzed by optical microscopy, transmission electron microscopy, and electron backscattered diffraction. The results showed that, on the outmost surface, nanograins with an average grain size of ∼100 nm were achieved. In the subsurface, i.e., the deformation twinning region, a large volume fraction of {10$\overline 1$2} deformation twins together with a low fraction of {11$\overline 2$2} and {11$\overline 2$4} twins were identified. Based on the microstructural analysis, the grain refinement mechanisms with increasing strain are summarized as: (i) prior division by deformation twinning, (ii) refinement effect of subgrain boundaries resulting from the accumulation of high density of dislocation, and (iii) transformation effect from low angle grain boundaries to high angle grain boundaries. The results of tension tests also show that the titanium sample after SRT shows higher strength than the as-received titanium sample.

Type
Articles
Information
Journal of Materials Research , Volume 29 , Issue 4 , 28 February 2014 , pp. 569 - 577
Copyright
Copyright © Materials Research Society 2014 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

Lee, I-S., Kim, D-H., Kim, H-E., Jung, Y-C., and Han, C-H.: Biological performance of calcium phosphate films formed on commercially pure Ti by electron-beam evaporation. Biomaterials 23, 609 (2002).CrossRefGoogle Scholar
Hall, E.O.: The deformation and ageing of mild steel: III discussion of results. Phys. Soc. B 64, 747 (1951).CrossRefGoogle Scholar
Petch, N.J. and Lron, J.: The cleavage strength of polycrystals. Steel Inst. 174, 25 (1953).Google Scholar
Valiev, R.Z., Islamgaliev, R.K., and Alexandrov, I.V.: Bulk nanostructured materials from severe plastic deformation. Prog. Mater. Sci. 45, 103 (2000).CrossRefGoogle Scholar
Tao, N.R., Wang, Z.B., Tong, W.P., Sui, M.L., Lu, J., and Lu, K.: An investigation of surface nanocrystallization mechanism in Fe induced by surface mechanical attrition treatment. Acta Mater. 50, 4603 (2002).Google Scholar
Wang, Y.M. and Ma, E.: High tensile ductility in a nanostructured metal. Appl. Phys. Lett. 80, 2395 (2002).Google Scholar
Roland, T., Retraint, D., Lu, K., and Lu, J.: Fatigue life improvement through surface nanostructuring of stainless steel by means of surface mechanical attrition treatment. Scr. Mater. 54, 1949 (2006).Google Scholar
Fang, T.H., Li, W.L., Tao, N.R., and Lu, K.: Revealing extraordinary intrinsic tensile plasticity in gradient nano-grained copper. Science 331, 1587 (2011).CrossRefGoogle ScholarPubMed
Yang, D.K. and Hodgson, P.D.: Tough ultrafine-grained Ti through multilayering and grading. Scr. Mater. 68, 309 (2013).CrossRefGoogle Scholar
Wen, M., Wen, C., Hodgson, P., and Li, Y.: Improvement of the biomedical properties of titanium using SMAT and thermal oxidation. Colloids Surf., B (2013, in press).Google ScholarPubMed
Li, J. and Soh, A.K.: Modeling of the plastic deformation of nanostructured materials with grain size gradient. Int. J. Plast. 39, 88 (2012).CrossRefGoogle Scholar
Avilés, R., Albizuri, J., Rodríguez, A., and López de Lacalle, L.N.: Influence of low-plasticity ball burnishing on the high-cycle-fatigue strength of medium carbon AISI 1045 steel. Int. J. Fatigue 55, 230 (2013).CrossRefGoogle Scholar
Prevéy, P.S. and Cammett, J.T.: The influence of surface enhancement by low plasticity burnishing on the corrosion fatigue performance of AA7075-T6. Int. J. Fatigue 26, 975 (2004).CrossRefGoogle Scholar
Dheda, S.S. and Mohamed, F.A.: Effect of initial microstructure on the processing of titanium using equal channel angular pressing. Mater. Sci. Eng., A 528, 8179 (2011).Google Scholar
Terada, D., Inoue, S., and Tsuji, N.: Microstructure and mechanical properties of commercial purity titanium severely deformed by ARB process. J. Mater. Sci. 42, 1673 (2007).Google Scholar
Chen, Y.J., Li, Y.J., Walmsley, J.C., Dumoulin, S., and Roven, H.J.: Deformation structures of pure titanium during shear deformation. Metall. Trans. A 41, 787 (2010).CrossRefGoogle Scholar
Yang, D.K., Cizek, P., Hodgson, P.D., and Wen, C.E.: Microstructure evolution and nanograin formation during shear localization in cold-rolled titanium. Acta Mater. 58, 4536 (2010).Google Scholar
Tao, N.R. and Lu, K.: Nanoscale structural refinement via deformation twinning in face-centered cubic metals. Scr. Mater. 60, 1039 (2009).CrossRefGoogle Scholar
Ghaderi, A. and Barnett, M.R.: Sensitivity of deformation twinning to grain size in titanium and magnesium. Acta Mater. 59, 7824 (2011).Google Scholar
Zhao, X.C., Fu, W.J., Yang, X.R., and Langdon, T.G.: Microstructure and properties of pure titanium processed by equal-channel angular pressing at room temperature. Scr. Mater. 59, 542 (2008).CrossRefGoogle Scholar
Zhu, K.Y., Vassel, A., Brisset, F., Lu, K., and Lu, J.: Nanostructure formation mechanism of α-titanium using SMAT. Acta Mater. 52, 4101 (2004).Google Scholar
Li, W.L., Tao, N.R., and Lu, K.: Fabrication of a gradient nano-micro-structured surface layer on bulk copper by means of a surface mechanical grinding treatment. Scr. Mater. 59, 546 (2008).Google Scholar
Chen, W., Sun, Q., Xiao, L., and Sun, J.: Deformation-induced grain refinement and amorphization in Ti-10V-2Fe-3Al alloy. Metall. Mater. Trans. A 43, 316 (2012). CrossRefGoogle Scholar
Youssef, K., Sakaliyska, M., Bahmanpour, H., Scattergood, R., and Koch, C.: Effect of stacking fault energy on mechanical behavior of bulk nanocrystalline Cu and Cu alloys. Acta Mater. 59, 5758 (2011).CrossRefGoogle Scholar
Yang, D.K., Cizek, P., Fabijanic, D., Wang, J.T., and Hodgson, P.D.: Work hardening in ultrafine-grained titanium: Multilayering and grading. Acta Mater. 61, 2840 (2013).CrossRefGoogle Scholar
Xiao, L.: Twinning behavior in the Ti–5at.% Al single crystals during cyclic loading along [0001]. Mater. Sci. Eng., A 394, 168 (2005).CrossRefGoogle Scholar
Hong, S-G., Park, S.H., and Lee, C.S.: Role of {10-12} twinning characteristics in the deformation behavior of a polycrystalline magnesium alloy. Acta Mater. 58, 5873 (2010).Google Scholar
Obara, T., Yoshinaga, H., and Morozumi, A.: {1122} <1123> slip system in magnesium. Acta Metall. 21, 845 (1973).Google Scholar
Li, B., Joshi, S.P., Almagri, O., Ma, Q., Ramesh, K.T., and Mukai, T.: Rate-dependent hardening due to twinning in an ultrafine-grained magnesium alloy. Acta Mater. 60, 1818 (2012).CrossRefGoogle Scholar
Zener, C. and Hollomon, J.H.: Effect of strain rate upon plastic flow of steel. J. Appl. Phys. 15, 22 (1944).Google Scholar
Li, Y.S., Zhang, Y., Tao, N.R., and Lu, K.: Effect of the Zener–Hollomon parameter on the microstructures and mechanical properties of Cu subjected to plastic deformation. Acta Mater. 57, 761 (2009).Google Scholar
Christian, J.W. and Mahajan, S.: Deformation twinning. Prog. Mater. Sci. 39, 1 (1995).Google Scholar
Kim, I., Kim, J., Shin, D.H., Liao, X.Z., and Zhu, Y.T.: Deformation twins in pure titanium processed by equal channel angular pressing. Scr. Mater. 48, 813 (2003).CrossRefGoogle Scholar
Ma, Q., El Kadiri, H., Oppedal, A.L., Baird, J.C., Horstemeyer, M.F., and Cherkaoui, M.: Twinning and double twinning upon compression of prismatic textures in an AM30 magnesium alloy. Scr. Mater. 64, 813 (2011).CrossRefGoogle Scholar
Li, Y.P., Wu, S., Bian, H.K., Tang, N., Liu, B., Koizumi, Y., and Chiba, A.: Grain refinement due to complex twin formation in rapid hot forging of magnesium alloy. Scr. Mater. 68, 171 (2013).Google Scholar
Ulacia, I., Dudamell, N.V., Galvez, F., Yi, S., Perez-Prado, M.T., and Hurtado, I.: Mechanical behavior and microstructural evolution of a Mg AZ31 sheet at dynamic strain rates. Acta Mater. 58, 2988 (2010).Google Scholar
Barnett, M.R., Keshavarz, Z., Beer, A.G., and Atwell, D.: Influence of grain size on the compressive deformation of wrought Mg–3Al–1Zn. Acta Mater. 52, 5093 (2004).CrossRefGoogle Scholar
Shin, D.H., Kim, I., Kim, J., Kim, Y.S., and Semiatin, S.L.: Microstructure development during equal-channel angular pressing of titanium. Acta Mater. 51, 983 (2003).Google Scholar
Chen, Y.J., Li, Y.J., Walmsley, J.C., Dumoulin, S., Gireesh, S.S., Armada, S., Skaret, P.C., and Roven, H.J.: Quantitative analysis of grain refinement in titanium during equal channel angular pressing. Scr. Mater. 64, 904 (2011).Google Scholar
Gorkaya, T., Molodov, K.D., Molodov, D.A., and Gottstein, G.: Concurrent grain boundary motion and grain rotation under an applied stress. Acta Mater. 59, 5674 (2011).CrossRefGoogle Scholar
Lim, A.T., Haataja, M., Cai, W., and Srolovitz, D.J.: Stress-driven migration of simple low-angle mixed grain boundaries. Acta Mater. 60, 1395 (2012).Google Scholar
Janssens, K.G.F., Olmsted, D., Holm, E.A., Foiles, S.M., Plimpton, S.J., and Derlet, P.M.: Computing the mobility of grain boundaries. Nat. Mater. 5, 124 (2006).Google Scholar
Olmsted, D.L., Holm, E.A., and Foiles, S.M.: Survey of computed grain boundary properties in face-centered cubic metals—II: Grain boundary mobility. Acta Mater. 57, 3704 (2009).Google Scholar
Guo, Z., Miodownik, A.P., Saunders, N., and Schille, J.P.: Influence of stacking-fault energy on high temperature creep of alpha titanium alloys. Scr. Mater. 54, 2175 (2006).Google Scholar
Chun, Y.B., Yu, S.H., Semiatin, S.L., and Hwang, S.K.: Effect of deformation twinning on microstructure and texture evolution during cold rolling of CP-titanium. Mater. Sci. Eng., A 398, 209 (2005).Google Scholar
Zherebtsov, S.V., Dyakonov, G.S., Salem, A.A., Sokolenko, V.I., Salishchev, G.A., and Semiatin, S.L.: Formation of nanostructures in commercial-purity titanium via cryorolling. Acta Mater. 61, 1167 (2013).Google Scholar