Hostname: page-component-586b7cd67f-2brh9 Total loading time: 0 Render date: 2024-11-24T08:21:52.476Z Has data issue: false hasContentIssue false
  • English
  • Français

Fabrication of porous SiC-based ceramic microchannels via pyrolysis of templated preceramic polymers

Published online by Cambridge University Press:  01 June 2006

Quoc Dat Nghiem ,
Amit Asthana ,
In-Kyung Sung  and
Dong-Pyo. Kim
Quoc Dat Nghiem
Affiliation:
Department of Fine Chemical Engineering and Chemistry, Chungnam National University,Yuseong Gu, Daejeon 305-764, Republic of Korea
Amit Asthana
Affiliation:
Department of Fine Chemical Engineering and Chemistry, Chungnam National University,Yuseong Gu, Daejeon 305-764, Republic of Korea
In-Kyung Sung
Affiliation:
Department of Fine Chemical Engineering and Chemistry, Chungnam National University,Yuseong Gu, Daejeon 305-764, Republic of Korea
Dong-Pyo. Kim*
Affiliation:
Department of Fine Chemical Engineering and Chemistry, Chungnam National University,Yuseong Gu, Daejeon 305-764, Republic of Korea
*
a) Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

This article reports conversion chemistry of preceramic polymer to ceramic phase during the fabrication of high-temperature stable silicon carbide and silicon carbonitride monolithic porous microchannels. The micromolding in capillariesmethod is used to fabricate porous channels by the initial infiltration of a solution of 1.5-μm diameter silica spheres or 1-μm diameter polystyrene spheres into polydimethylsiloxane channels followed by filling the void space among the spheres by using viscous commercial polymeric precursors. Subsequently, the polymer-sphere composite channel was cured and pyrolysed at 1200 °C under inert atmosphere, and final wet etching step of silica spheres with 10% hydrofluoric acid solution developed the pore structures by removing the silica spheres, whereas polystyrene sphere decomposes at the early stage of pyrolysis.

Keywords

LithographyMicrostructurePorous ceramic
Type
Articles
Information
Journal of Materials Research , Volume 21 , Issue 6 , June 2006 , pp. 1543 - 1549
Copyright
Copyright © Materials Research Society 2006

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Madou, M.: Fundamentals of Microfabrication (CRC Press, New York, 1997).Google Scholar
2.Liew, L.A., Zhang, W., An, L., Shah, S., Luo, R., Liu, Y., Cross, T., Anseth, K., Dunn, M.L., Bright, V.M., Daily, J.W., Raj, R.: Ceramic MEMS: New materials, innovative processing and future applications. Am. Ceram. Soc. Bull. 80, 25 (2001).Google Scholar
3.Liew, L.A., Bright, V.M., Raj, R.: A novel micro-glow plug fabricated from polymer-derived ceramics: In situ measurement of high-temperature properties and application to ultrahigh-temperature ignition. Sens. Actuators, A 104, 246 (2003).CrossRefGoogle Scholar
4.Sung, I-K., Mitchell, M.C., Kim, D-P., Kenis, P.J.A.: Tailored macroporous SiC and SiCN structures for high temperature fuel reforming at the microscale. Adv. Funct. Mater. 15, 1336 (2005).CrossRefGoogle Scholar
5.Mehregany, M., Zorman, C.A., Rajan, N., Wu, C.H.: Silicon carbide MEMS for harsh environments. IEEE 86, 1594 (1998).CrossRefGoogle Scholar
6.Yang, H., Deschatelets, P., Brittain, S.T., Whitesides, G.M.: Fabrication of high performance ceramic microstructures from a polymeric precursor using soft lithography. Adv. Mater. 13, 54 (2001).3.0.CO;2-Y>CrossRefGoogle Scholar
7.Han, Y.H., Uekawa, N., Saito, T., Kakegawa, K.: Bonding of silicon nitride using preceramic polymer and germanium powders for potential fuel-cell applications. Adv. App. Ceram. 104, 239 (2005).CrossRefGoogle Scholar
8.Miele, P., Toury, B., Cornu, D., Bernard, S.: Borylborazines as new precursors for boron nitride fibres. J. Organomet. Chem. 690, 2809 (2005).CrossRefGoogle Scholar
9.Sung, I-K., Yoon, S-B., Yu, J-S., Kim, D-P.: Fabrication of macroporous SiC from templated preceramic polymers. Chem. Commun. 14, 1480 (2002).CrossRefGoogle Scholar
10.Park, K-H., Sung, I-K., Kim, D-P.: A facile fabrication of mesoporous SiC from templated preceramic polymers. J. Mater. Chem. 14, 3436 (2004).CrossRefGoogle Scholar
11.Stankiewicz, A.I., Moulijn, J.A. Process intensification: Transforming chemical engineering. Chem. Eng. Prog. (2000), p. 21.Google Scholar
12.Liu, W.: Ministructured catalyst bed for gas-liquid-solid multiphase catalytic reaction. AIChE J. 48, 1519 (2002).CrossRefGoogle Scholar
13.Gates, B., Xia, Y.: Fabrication and characterization of chirped 3D photonic crystals. Adv. Mater. 12, 1329 (2000).3.0.CO;2-V>CrossRefGoogle Scholar
14.Witula, T., Holmberg, K.: Use of a mesoporous material for organic synthesis. Langmuir 21, 3782 (2005).CrossRefGoogle ScholarPubMed
15.Williams, J.: Monolith structures, materials, properties and uses. Catal. Today 69, 3 (2001).CrossRefGoogle Scholar
16.Duffy, D.C., McDonald, J.C., Schueller, O.J.A., Whitesides, G.M.: Rapid prototyping of microfluidic systems in poly(dimethylsiloxane). Anal. Chem. 70, 4974 (1998).CrossRefGoogle ScholarPubMed
17.Kroke, E., Li, Y-L., Konetschny, C., Lecomte, E., Fasel, C., Riedel, A.: Silazane-derived ceramics and related materials. Mater. Sci. Eng. R 26, 97 (2000).CrossRefGoogle Scholar
18.Berndt, F., Jahn, P., Rendtel, A., Motz, G., Ziegler, G.: Monolithic SiOC ceramics with tailored porosity. Key Eng. Mater. 206–213, 1927 (2002).Google Scholar