Hostname: page-component-78c5997874-t5tsf Total loading time: 0 Render date: 2024-11-16T11:19:14.337Z Has data issue: false hasContentIssue false
  • English
  • Français

Fabrication, formation mechanism and properties of three-dimensional nanoporous titanium dealloyed in metallic powders

Published online by Cambridge University Press:  02 February 2017

Faming Zhang ,
Ping Li ,
Jin Yu ,
Lili Wang ,
Farhad Saba ,
Ge Dai  and
Siyuan He
Faming Zhang*
Affiliation:
Jiangsu Key Lab for Advanced Metallic Materials, School of Materials Science and Engineering, Southeast University, 211189 Nanjing, China; and State Key Laboratory for Powder Metallurgy, Central South University, Changsha 410083, China
Ping Li
Affiliation:
Jiangsu Key Lab for Advanced Metallic Materials, School of Materials Science and Engineering, Southeast University, Nanjing 211189, China
Jin Yu
Affiliation:
Jiangsu Key Lab for Advanced Metallic Materials, School of Materials Science and Engineering, Southeast University, Nanjing 211189, China
Lili Wang
Affiliation:
Jiangsu Key Lab for Advanced Metallic Materials, School of Materials Science and Engineering, Southeast University, Nanjing 211189, China
Farhad Saba
Affiliation:
Jiangsu Key Lab for Advanced Metallic Materials, School of Materials Science and Engineering, Southeast University, Nanjing 211189, China
Ge Dai
Affiliation:
Jiangsu Key Lab for Advanced Metallic Materials, School of Materials Science and Engineering, Southeast University, Nanjing 211189, China
Siyuan He
Affiliation:
School of Biological Science and Medical Engineering, Southeast University, Nanjing 210096, China
*
a) Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

We present a novel route to fabricate 3D nanoporous α-Ti foams by dealloying of TiCu master alloy in solid state using Mg powders. Pure open-cell nanoporous α-Ti foams are fabricated with BET surface area of 34.4 ± 0.8 m2/g and pore size in the range of 2–50 nm. The dealloying using powders is a solid state chemical reaction process to form Cu2Mg phase and Ti/Mg nanocomposites. The constituent of Cu in the TiCu alloy was dissolved into Mg powders thanks to the kinetics of interface reaction and volume diffusion. The pore-forming mechanism is a solid-state interdiffusion process. The ligament coarsening is from 492 to 650 nm with increasing of the dealloying temperature. The hardness and elastic modulus in nanoporous α-Ti foam follow linear decay fit with ligament size increasing. Our results demonstrate a facile strategy for the fabrication of nanoporous Ti foams with novel nanostructures and tailored properties.

Keywords

Nanoporous metalsDealloyingTitaniumMetal foamSpark plasma sintering
Type
Articles
Information
Journal of Materials Research , Volume 32 , Issue 8 , 28 April 2017 , pp. 1528 - 1540
Check for updates
Copyright
Copyright © Materials Research Society 2017 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

Footnotes

Contributing Editor: Jürgen Eckert

References

REFERENCES

Tappan, B.C., Steiner, S.A. III, and Luther, E.P.: Nanoporous metal foams. Angew. Chem., Int. Ed. 49, 4544 (2010).Google Scholar
Jin, H.J., Wang, X.L., Parida, S., Wang, K., Seo, M., and Weissmuller, J.: Nanoporous Au–Pt alloys as large strain electrochemical actuators. Nano Lett. 10, 187 (2010).CrossRefGoogle ScholarPubMed
Li, X., Chen, Q., McCue, I., Snyder, J., Crozier, P., Erlebacher, J., and Sierzdzki, K.: Dealloying of noble-metal alloy nanoparticles. Nano Lett. 14, 2569 (2014).CrossRefGoogle ScholarPubMed
Ghosh, S.: Switching magnetic order in nanoporous Pd–Ni by electrochemical charging. J. Mater. Res. 28, 3010 (2013).Google Scholar
Qi, Z. and Weissmueller, J.: Hierarchical nested-network nanostructure by dealloying. ACS Nano 7, 5948 (2013).Google Scholar
Erlebacher, J., Aziz, M.J., Karma, A., Dimitrov, N., and Sieradzk, K.: Evolution of nanoporosity in dealloying. Nature 410, 450 (2001).Google Scholar
Shin, K., Leach, K.A., Goldbach, J.T., Kim, D.H., Jho, J.Y., Tuominen, M., Hawker, C.J., and Russell, T.P.: A simple route to metal nanodots and nanoporous metal films. Nano Lett. 2, 933 (2002).CrossRefGoogle Scholar
Naeth, O., Stephen, A., Roesler, J., and Vollertsen, F.: Structuring of nanoporous nickel-based superalloy membranes via laser etching. J. Mater. Process. Technol. 209, 4739 (2009).Google Scholar
Tappan, B.C., Huynh, M.H., Hiskey, M.A., Chavez, D.E., Luther, E.P., Mang, J.T., and Son, S.F.: Ultralow-density nanostructured metal foams: combustion synthesis, morphology, and composition. J. Am. Chem. Soc. 128, 6589 (2006).Google Scholar
Qi, Z., Vainio, U., Kornowski, A., Ritter, M., Weller, H., Jin, H., and Weissmueller, J.: Porous gold with a nested-network architecture and ultrafine structure. Adv. Funct. Mater. 25, 2530 (2015).CrossRefGoogle Scholar
Thorp, J.C., Sieradzki, K., Tang, L., Crozier, P.A., Misra, A., Nastasi, M., Mitlin, D., and Picraux, S.T.: Formation of nanoporous noble metal thin films by electrochemical dealloying of Pt x Si1x . Appl. Phys. Lett. 88, 033110 (2006).Google Scholar
Hakamada, M. and Mabuchi, M.: Fabrication of nanoporous palladium by dealloying and its thermal coarsening. J. Alloys Compd. 479, 326 (2009).Google Scholar
Tang, Y., Liu, Y., Lian, L., Zhou, X., and He, L.: Formation of nanoporous copper through dealloying of dual-phase Cu–Mn–Al alloy: The evolution of microstructure and composition. J. Mater. Res. 27, 2771 (2012).CrossRefGoogle Scholar
Hakamada, M. and Mabuchi, M.: Preparation of nanoporous Ni and Ni–Cu by dealloying of rolled Ni–Mn and Ni–Cu–Mn alloys. J. Alloys Compd. 485, 583 (2009).Google Scholar
Zhang, F., Weidmann, A., Nebe, J.B., Beck, U., and Burkel, E.: Preparation, microstructures, mechanical properties and cytocompatibility of TiMn alloys for biomedical applications. J. Biomed. Mater. Res., B 94, 406 (2010).CrossRefGoogle ScholarPubMed
Wada, T., Yubuta, K., Inoue, A., and Kato, H.: Dealloying by metallic melt. Mater. Lett. 65, 1076 (2011).CrossRefGoogle Scholar
Panagiotopoulos, N.T., Moreira Jorge, A., Rebai, I., Georgarakis, K., Botta, W.J., and Yavari, A.R.: Nanoporous titanium obtained from a spinodally decomposed Ti alloy. Microporous Mesoporous Mater. 222, 26 (2016).Google Scholar
Tsuchiya, H., Berger, S., and Macak, J.M.: Self-organized porous and tubular oxide layers on TiAl alloys. Electrochem. Commun. 9, 2397 (2007).Google Scholar
Abe, H., Sato, K., Nishikawa, H., Takemoto, T., Fukuhara, M., and Inoue, A.: Dealloying of Cu–Zr–Ti bulk metallic glass in hydrofluoric acid solution. Mater. Trans. 50, 1255–1258 (2009).Google Scholar
Tsuda, M., Wada, T., and Kato, H.: Kinetics of formation and coarsening of nanoporous-titanium dealloyed with Mg melt. J. Appl. Phys. 114, 113503 (2013).Google Scholar
Wada, T., Setyawan, A.D., Yubuta, K., and Kato, H.: Nano- to submicro-porous beta-Ti alloy prepared from dealloying in a metallic melt. Script. Mater. 65, 532 (2011).Google Scholar
Kim, J.W., Tsuda, M., Wada, T., Yubuta, K., Kim, S.G., and Kato, H.: Optimizing niobium dealloying with metallic melt to fabricate porous structure for electrolytic capacitors. Acta Mater. 84, 497 (2015).CrossRefGoogle Scholar
Wada, T. and Kato, H.: Three-dimensional open-cell macroporous iron, chromium and ferritic stainless steel. Scr. Mater. 68, 723 (2013).Google Scholar
Chen-Wiegart, Y.K., Wada, T., Butakov, N., Xiao, X., De Carlo, F., Kato, H., Wang, J., Dunand, D.C., and Maire, E.: 3D morphological evolution of porous titanium by X-ray micro- and nano-tomography. J. Mater. Res. 28, 2444 (2013).Google Scholar
Dunand, D.C.: Processing of titanium foams. Adv. Eng. Mater. 6, 369 (2004).Google Scholar
Zhang, F., Otterstein, E., and Burkel, E.: Spark plasma sintering, microstructures and mechanical properties of macroporous titanium foams. Adv. Eng. Mater. 12, 863 (2010).Google Scholar
Guillon, O., Julian, J.G., Dargatz, B., Kessel, T., Schierning, G., Rathel, J., and Herrmann, M.: Field-assisted sintering technology/spark plasma sintering: Mechanisms, materials, and technology developments. Adv. Eng. Mater. 16, 830 (2014).CrossRefGoogle Scholar
Zhang, F., Reich, M., Kessler, O., and Burkel, E.: Potential of rapid cooling spark plasma sintering for metallic materials. Mater. Today 16, 192–195 (2013).Google Scholar
Takeuchi, A. and Inoue, A.: Classification of bulk metallic glasses by atomic size difference, heat of mixing and period of constituent elements and its application to characterization of the main alloying element. Mater. Trans. 46, 2817 (2005).Google Scholar
Erlebacher, J. and Seshadri, R.: Hard materials with tunable porosity. MRS Bull. 34, 561 (2009).Google Scholar
Meguro, K., O, M., and Kajihara, M.: Growth behavior of compounds due to solid-state reactive diffusion between Cu and Al. J. Mater. Sci. 47, 4955–4964 (2012).Google Scholar
Corcoran, Y.L., King, A.H., Lanerolle, N.D., and Kim, B.: Grain boundary diffusion and growth of titanium silicide layers on silicon. J. Electron. Mater. 19, 1177 (1990).Google Scholar
Taguchi, O., Iijima, Y., and Hirono, K.: Reaction diffusion in the Cu–Ti system. J. Jpn. Inst. Met. 54, 619 (1990).CrossRefGoogle Scholar
Hakamada, M. and Mabuchi, M.: Mechanical strength of nanoporous gold fabricated by dealloying. Scr. Mater. 56, 1003 (2007).Google Scholar
Wada, T., Yubuta, K., and Kato, H.: Evolution of a biocontinuous nanostructure via a solid-state interfacial dealloying reaction. Scr. Mater. 118, 33 (2016).Google Scholar
Necula, B.S., Apachitei, I., Fratila-Apachitei, L.E., van Langelaan, E.J., and Duszczyk, J.: Titanium bone implants with superimposed micro/nano-scale porosity and antibacterial capability. Appl. Surf. Sci. 273, 310 (2013).Google Scholar