Hostname: page-component-586b7cd67f-g8jcs Total loading time: 0 Render date: 2024-11-30T23:20:59.207Z Has data issue: false hasContentIssue false
  • English
  • Français

Fabrication and properties of HfB2–MoSi2 composites produced by hot pressing and spark plasma sintering

Published online by Cambridge University Press:  01 June 2006

Diletta Sciti ,
Laura Silvestroni  and
Alida Bellosi
Diletta Sciti*
Affiliation:
CNR-ISTEC, Institute of Science and Technology for Ceramics, I-48018 Faenza, Italy
Laura Silvestroni
Affiliation:
CNR-ISTEC, Institute of Science and Technology for Ceramics, I-48018 Faenza, Italy
Alida Bellosi
Affiliation:
CNR-ISTEC, Institute of Science and Technology for Ceramics, I-48018 Faenza, Italy
*
a) Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

HfB2–15 vol% MoSi2 composites were produced from powder mixtures and densified through different techniques, namely hot pressing and spark plasma sintering. Dense materials were obtained at 1900 °C by hot pressing and at 1750 °C by spark plasma sintering. Microstructure and mechanical properties were compared. The most relevant result was for high-temperature strength: independent of the processing technique, the flexural strength in air at 1500 °C was higher than 500 MPa.

Keywords

HfSinteringStrength
Type
Articles
Information
Journal of Materials Research , Volume 21 , Issue 6 , June 2006 , pp. 1460 - 1466
Copyright
Copyright © Materials Research Society 2006

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Opeka, M.M., Talmy, I.G., Zaykoski, J.A.: Oxidation-based materials selection for 2000 °C+ hypersonic aerosurfaces: Theoretical consideration and historical experience. J. Mater. Sci. 39, 5887 (2004).CrossRefGoogle Scholar
2.Upadhya, K., Yang, J.M., Hoffmann, W.P.: Materials for ultrahigh temperature structural applications. Am. Ceram. Soc. Bull. 58, 51 (1997).Google Scholar
3.Van Goor, G. de, Sagesser, P., Berroth, K. Electrically conductive ceramic composites, in Advanced Multilayered and Fibre-Reinforced Composites edited by Haddad, Y.M. (Kluwer Academic, The Netherlands, 1998), pp. 311–322.CrossRefGoogle Scholar
4.Clougherty, E.V., Kalishi, D., and Peters, E.T.: Research and development of refractory oxidation resistant diborides, Technical Report AFML-TR-68-190 (1968).Google Scholar
5.Gasch, M., Elleby, D., Irby, E.I., Beckam, S., Gusman, M., Johnson, S.: Processing, properties and arc jet oxidation of hafnium diboride/silicon carbide ultra high temperature ceramics. J. Mater. Sci. 39, 5925 (2004).CrossRefGoogle Scholar
6.Opeka, M.M., Talmy, I.G., Wuchina, E.J., Zaykoski, J.A., Causey, S.J.: Mechanical, thermal, and oxidation properties of refractory hafnium and zirconium compounds. J. Eur. Ceram. Soc. 19, 2405 (1999).CrossRefGoogle Scholar
7.Wuchina, E., Opeka, M., Causey, S., Buesking, K., Spain, J., Cull, A., Routbort, J., Guitierrez-Mora, F.: Designing for ultrahigh-temperature applications: The mechanical and thermal properties of HfB2, HfCx, HfNx, and Hf(N). J. Mater. Sci. 39, 5939 (2004).CrossRefGoogle Scholar
8.Medri, V. and Bellosi, A.: Microstructure and properties of hot pressed hafnium diboride with silicon nitride as sintering aid (unpublished).Google Scholar
9.Monteverde, F., Bellosi, A.: Efficacy of HfN as sintering aid in the manufacture of ultrahigh-temperature metal diborides-matrix ceramics. J. Mater. Res. 19, 3576 (2004).CrossRefGoogle Scholar
10.Chamberlain, A.L., Fahrenholtz, W.G., Hilmas, G.E. Characterization of zirconium diboride-molybdenum disilicide ceramics, in Advances in Ceramic Matrix Composites IX Ceram. Trans. Vol. 153, edited by Bansal, N.P., Singh, J.P., Kriven, W.M., and Schneider, H., (Am. Ceram. Soc., Westerville, OH, 2003), p. 299.Google Scholar
11.Sciti, D., Brach, M., Bellosi, A.: Oxidation behavior of a pressureless sintered ZrB2–MoSi2 ceramic composite. J. Mater. Res. 20, 922 (2005).CrossRefGoogle Scholar
12.Munz, D.G.Shannon, J.L. Jr.Bubsey, R.T.: Fracture toughness calculation from maximum load in four point bend tests of chevron notch specimens. Int. J. Fract. 16, R137 (1980).CrossRefGoogle Scholar
13.Nygren, M., Shen, Z.: Novel assemblies via spark plasma sintering. Silic. Indus. 69, 211 (2004).Google Scholar
14.Mamedov, V.: Spark plasma sintering as advanced PM sintering method. Powder Metall. 45, 322 (2002).CrossRefGoogle Scholar
15.Groza, J.R., Zavaliangons, A.: Sintering activation by electrical field. Mater. Sci. Eng. A 287, 171 (2000).CrossRefGoogle Scholar
16.Jeng, Y-L., Lavernia, E.J.: Review: Processing of molybdenum disilicide. J. Mater. Sci. 29, 2557 (1994).CrossRefGoogle Scholar
17.Levin, E.M., Robbins, C.R., Murdie, H.F. McPhase diagram for ceramists (Am. Ceram. Soc., Columbus, OH, 1969), 1969 Suppl., p. 98.Google Scholar
18.Monteverde, F., Bellosi, A.: Microstructure and properties of an HfB2-SiC composite for ultra high temperature applications. Adv. Eng. Mater. 6, 331 (2004).CrossRefGoogle Scholar
19.Zhu, Y.T., Stan, M., Conzone, S.D., Butt, D.P.: Thermal oxidation kinetics of MoSi2-based powders. J. Am. Ceram. Soc. 82, 2785 (1999).CrossRefGoogle Scholar