Hostname: page-component-78c5997874-mlc7c Total loading time: 0 Render date: 2024-11-04T18:24:09.795Z Has data issue: false hasContentIssue false

Effects of strain hardening and residual stress in impression on the instrumented indentation technique

Published online by Cambridge University Press:  01 July 2006

L.Z. Liu
Affiliation:
Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016, People's Republic of China
Y.W. Bao
Affiliation:
Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016, People's Republic of China; and China Building Materials Academy, Guanzhuang, Beijing 100024, People's Republic of China
Y.C. Zhou*
Affiliation:
Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016, People's Republic of China
*
a) Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

Finite element analyses were carried out to simulate the loading, unloading, and reloading processes of indentation tests. It was found that the validity of applying the elastic contact theory to the indentation unloading process is strongly related to the strain hardening and residual stress in impression. It is the combination of strain hardening and residual stress that causes the unloading or reloading curves to show elastic loading in the range from zero to the maximum load whereas the reloading curve on the impression without strain hardening and residual stress shows elastic–plastic loading in the same range. These computations indicate that applying the elastic contact theory to the unloading or reloading processes, the fundamental prerequisite of the instrumented indentation technique, is valid because of the existence of strain hardening and residual stress. The mechanism of this hardening effect is discussed through energy analysis.

Type
Articles
Copyright
Copyright © Materials Research Society 2006

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Cheng, Y.T., Cheng, C.M.: Scaling, dimensional analysis, and indentation measurements. Mater. Sci. Eng. R-Rep. 44, 91 (2004).CrossRefGoogle Scholar
2.Dao, M., Chollacoop, N., Van Vliet, K.J., Venkatesh, T.A., Suresh, S.: Computational modeling of the forward and reverse problems in instrumented sharp indentation. Acta Mater. 49, 3899 (2001).Google Scholar
3.Ni, W.Y., Cheng, Y.T., Cheng, C.M., Grummon, D.S.: An energy-based method for analyzing instrumented spherical indentation experiments. J. Mater. Res. 19, 149 (2004).Google Scholar
4.Pharr, G.M., Bolshakov, A.: Understanding nanoindentation unloading curves. J. Mater. Res. 17, 2660 (2002).CrossRefGoogle Scholar
5.Schwarzer, N.: Elastic surface deformation due to indenters with arbitrary symmetry of revolution. J. Phys. D Appl. Phys. 37, 2761 (2004).CrossRefGoogle Scholar
6.Woirgard, J., Dargenton, J.C.: An alternative method for penetration depth determination in nanoindentation measurements. J. Mater. Res. 12, 2455 (1997).Google Scholar
7.Borodich, F.M.: The Hertz frictional contact between nonlinear elastic anisotropic bodies (the similarity approach). Int. J. Solids Struct. 30, 1513 (1993).CrossRefGoogle Scholar
8.Bao, Y.W., Wang, W., Zhou, Y.C.: Investigation of the relationship between elastic modulus and hardness based on depth-sensing indentation measurements. Acta Mater. 52, 5397 (2004).Google Scholar
9.Nix, W.D., Gao, H.J.: Indentation size effects in crystalline materials: A law for strain gradient plasticity. J. Mech. Phys. Solids 46, 411 (1998).Google Scholar
10.Doerner, M.F., Nix, W.D.: A method for interpreting the data from depth-sensing indentation instruments. J. Mater. Res. 1, 601 (1986).CrossRefGoogle Scholar
11.Oliver, W.C., Pharr, G.M.: An improved technique for determining hardness and elastic-modulus using load and displacement sensing indentation experiments. J. Mater. Res. 7, 1564 (1992).CrossRefGoogle Scholar
12.Sneddon, I.N.: The relation between load and penetration in the axisymmetric boussinesq problem for a punch of arbitrary profile. Int. J. Eng. Sci. 3, 47 (1965).CrossRefGoogle Scholar
13.Oliver, W.C., Pharr, G.M.: Measurement of hardness and elastic modulus by instrumented indentation: Advances in understanding and refinements to methodology. J. Mater. Res. 19, 3 (2004).CrossRefGoogle Scholar
14.Gong, J.H., Miao, H.Z., Peng, Z.J.: Analysis of the nanoindentation data measured with a Berkovich indenter for brittle materials: Effect of the residual contact stress. Acta Mater. 52, 785 (2004).CrossRefGoogle Scholar
15.Borodich, F.M., Keer, L.M.: Contact problems and depth-sensing nanoindentation for frictionless and frictional boundary conditions. Int. J. Solids Struct. 41, 2479 (2004).CrossRefGoogle Scholar
16.Bolshakov, A., Oliver, W.C., Pharr, G.M.: Influences of stress on the measurement of mechanical properties using nanoindentation: Part II. Finite element simulations. J. Mater. Res. 11, 760 (1996).Google Scholar
17.Mata, M., Alcalá, J.: The role of friction on sharp indentation. J. Mech. Phys. Solids 52, 145 (2004).CrossRefGoogle Scholar
18. ANSYS theory manual version 7.0 ANSYS Inc.Google Scholar
19.Johnson, K.L.: The correlation of indentation experiments. J. Mech. Phys. Solids 18, 115 (1970).CrossRefGoogle Scholar
20.Mata, M., Casals, O., and Alcalá, J.: The plastic zone size in indentation experiments: The analogy with the expansion of a spherical cavity. Int. J. Solids Struct. (2005) available online at www.sciencedirect.com.Google Scholar