Hostname: page-component-cd9895bd7-p9bg8 Total loading time: 0 Render date: 2024-12-27T06:48:38.352Z Has data issue: false hasContentIssue false
  • English
  • Français

Effects of lattice defects on indentation-induced plasticity initiation behavior in metals

Published online by Cambridge University Press:  30 May 2012

T. Ohmura ,
L. Zhang ,
K. Sekido  and
K. Tsuzaki
T. Ohmura*
Affiliation:
Structural Materials Unit, National Institute for Materials Science, Tsukuba, Ibaraki 305-0047, Japan
L. Zhang
Affiliation:
Structural Materials Unit, National Institute for Materials Science, Tsukuba, Ibaraki 305-0047, Japan
K. Sekido
Affiliation:
Department of Materials Science and Engineering, University of Tsukuba, Tsukuba, Ibaraki, Japan
K. Tsuzaki
Affiliation:
Structural Materials Unit, National Institute for Materials Science, Tsukuba, Ibaraki 305-0047, Japan; and University of Tsukuba, Tsukuba, Ibaraki, Japan
*
a)Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

Plasticity initiation behavior that appears as a pop-in phenomenon on a loading process during indentation-induced deformation was investigated to reveal the effects of lattice defects such as grain boundary and solute element for various metallic materials including Fe alloys through instrumented nanoindentation techniques. The critical load Pc of pop-in on a loading process is lower in the vicinity of the grain boundary than in the grain interior, but the relative hardness of the boundary is equal to or greater than that in grain interior. In-solution Si produces a larger increase in the Pc for both the grain boundary and the grain interior in the Fe–Si alloy than in the interstitial-free steel. The maximum shear stress corresponding to the Pc underneath the indenter is directly proportional to the shear modulus in single crystals with various crystallographic structures. Microstructural effects on the Pc are considered based on some dislocation models.

Type
Articles
Information
Journal of Materials Research , Volume 27 , Issue 13 , 14 July 2012 , pp. 1742 - 1749
Copyright
Copyright © Materials Research Society 2012

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Ohmura, T., Hara, T., and Tsuzaki, K.: Relationship between nanohardness and microstructures in high-purity Fe-C as-quenched and quench-tempered martensite. J. Mater. Res. 18, 1465 (2003).CrossRefGoogle Scholar
2.Ohmura, T., Minor, A., Stach, E., and Morris, J.W. Jr.: Dislocation—grain boundary interactions in martensitic steel observed through in-situ nanoindentation in a TEM. J. Mater. Res. 19, 3626 (2004).CrossRefGoogle Scholar
3.Gerberich, W.W., Nelson, J.C., Lilleodden, E.T., Anderson, P., and Wyrobek, J.T.: Indentation induced dislocation nucleation: The initial yield point. Acta Mater. 44, 3585 (1996).CrossRefGoogle Scholar
4.Corcoran, S.G., Colton, R.J., Lilleodden, E.T., and Gerberich, W.W.: Anomalous plastic deformation at surfaces: Nanoindentation of gold single crystals. Phys. Rev. B 55, R16057 (1997).CrossRefGoogle Scholar
5.Bahr, D.F., Kramer, D.K., and Gerberich, W.W.: Non-linear deformation mechanisms during nanoindentation. Acta Mater. 46, 3605 (1998).CrossRefGoogle Scholar
6.Gerberich, W.W., Kramer, D.K., Tymiak, N.I., Volinsky, A.A., Bahr, D.F., and Kriese, M.D.: Nanoindentation-induced defect-interface interactions: Phenomena, methods and limitations. Acta Mater. 47, 4115 (1999).CrossRefGoogle Scholar
7.Suresh, S., Nieh, T-G., and Choi, B.W.: Nano-indentation of copper thin films on silicon substrates. Scr. Mater. 41, 951 (1999).CrossRefGoogle Scholar
8.Gouldstone, A., Koh, H-J., Zeng, K-Y., Giannakopoulos, A.E., and Suresh, S.: Discrete and continuous deformation during nanoindentation of thin films. Acta Mater. 48, 2277 (2000).CrossRefGoogle Scholar
9.Lorenz, D., Zeckzer, A., Hilpert, U., Grau, P., Johansen, H., and Leipner, H.S.: Pop-in effect as homogeneous nucleation of dislocations during nanoindentation. Phys. Rev. B 67, 172101 (2003).CrossRefGoogle Scholar
10.Minor, A.M., Lilleodden, E.T., Stach, E.A., and Morris, J.W. Jr.: Direct observations of incipient plasticity during nanoindentation of Al. J. Mater. Res. 19, 176 (2004).CrossRefGoogle Scholar
11.Shibutani, Y. and Koyama, A.: Surface roughness effects on the displacement bursts observed in nanoindentation. J. Mater. Res. 19, 183 (2004).CrossRefGoogle Scholar
12.Tsuru, T., Shibutani, Y., and Kaji, Y.: Nanoscale contact plasticity of crystalline metal: Experiment and analytical investigation via atomistic and discrete dislocation models. Acta Mater. 58, 3096 (2010).CrossRefGoogle Scholar
13.Soer, W.A., Aifantis, K.E., and De Hosson, J.T.M.: Incipient plasticity during nanoindentation at grain boundaries in body-centered cubic metals. Acta Mater. 53, 4665 (2005).CrossRefGoogle Scholar
14.Ohmura, T., Tsuzaki, K., and Yin, F.: Nanoindentation-induced deformation behavior in the vicinity of single grain boundary of interstitial-free steel. Mater. Trans. 46, 2026 (2005).CrossRefGoogle Scholar
15.Minor, A.M., Asif, S.A.S., Shan, Z., Stach, E.A., Cyrankowski, E., Wyrobek, T.J., and Warren, O.L.: A new view of the onset of plasticity during the nanoindentation of aluminium. Nat. Mater. 5, 697 (2006).CrossRefGoogle ScholarPubMed
16.Ohmura, T. and Tsuzaki, K.: Plasticity initiation and subsequent deformation behavior in the vicinity of single grain boundary investigated through nanoindentation technique. J. Mater. Sci. 42, 1728 (2007).CrossRefGoogle Scholar
17.Sekido, K., Ohmura, T., Hara, T., and Tsuzaki, K.: Effect of Dislocation Density on the Initiation of Plastic Deformation on Fe–C Steels. Mater. Trans. 53, 907 (2012).CrossRefGoogle Scholar
18.Wang, M.G. and Ngan, A.H.W.: Indentation strain burst phenomenon induced by grain boundaries in niobium. J. Mater. Res. 19, 2478 (2004).CrossRefGoogle Scholar
19.Britton, T.B., Randman, D., and Wilkinson, A.J.: Nanoindentation study of slip transfer phenomenon at grain boundaries. J. Mater. Res. 24, 607 (2009).CrossRefGoogle Scholar
20.Yoshitomi, Y., Suzuki, S., Ueda, T., Tsurekawa, S., Nakashima, H., and Yoshinaga, H.: Grain boundary segregation in <110> symmetrical tilt bicrystals of an Fe-3%Si alloy. Scr. Metall. 32, 1067 (1995).CrossRefGoogle Scholar
21.Oliver, W.C. and Pharr, G.M.: Improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments. J. Mater. Res. 7, 1564 (1992).CrossRefGoogle Scholar
22.Johnson, K.L.: Contact Mechanics (Cambridge University Press, Cambridge, UK, 1985) pp. 84–106.CrossRefGoogle Scholar
23.Shim, S., Bei, H., George, E.P., and Pharr, G.M.: A different type of indentation size effect. Scr. Mater. 59, 1095 (2008).CrossRefGoogle Scholar
24.Eliash, T., Kazakevich, M., Semenov, V.N., and Rabkin, E.: Nanohardness of molybdenum in the vicinity of grain boundaries and triple junctions. Acta Mater. 56, 5640 (2008).CrossRefGoogle Scholar
25.Westbrook, J.H.: Segregation at grain boundaries. Int. Mater. Rev. 9, 415 (1964).Google Scholar
26.Dieter, G.E.: Mechanical Metallurgy (McGraw-Hill, New York, 1986) p. 179.Google Scholar
27.Sekido, K., Ohmura, T., Zhang, L., Hara, T., and Tsuzaki, K.: The effect of interstitial carbon on the initiation of plastic deformation of steels. Mater. Sci. Eng., A 530, 396 (2011).CrossRefGoogle Scholar
28.Dub, S.N., Zasimchuk, I.K., and Matvienko, L.F.: Effect of solid solution strengthening by iridium on the nucleation of dislocations in a molybdenum single crystal during nanoindentation. Phys. Solid State 53, 1404 (2011).CrossRefGoogle Scholar
29.Dub, S.N., Lim, Y.Y., and Chaudhri, M.M.: Nanohardness of high purity Cu (111) single crystal: The effect of indenter load and prior plastic sample strain. J. Appl. Phys. 107, 043510 (2010).CrossRefGoogle Scholar
30.Sestak, B. and Libovicky, S.: Transition to crystallographic slip on Fe-3% Si single crystals at 78K. Acta Metall. 11, 1190 (1963).CrossRefGoogle Scholar
31.Boettner, R.C. and McEvily, A.J. Jr.: Fatigue slip band formation in silicon-iron. Acta Metall. 13, 937 (1965).CrossRefGoogle Scholar