Hostname: page-component-586b7cd67f-rcrh6 Total loading time: 0 Render date: 2024-11-24T15:32:40.026Z Has data issue: false hasContentIssue false
  • English
  • Français

Effect of nitrogen flow ratio on the microstructure evolution and nanoindented mechanical property of the Ta–Si–N thin films

Published online by Cambridge University Press:  31 January 2011

C.K. Chung  and
T.S. Chen
C.K. Chung*
Affiliation:
Department of Mechanical Engineering, Center for Micro/Nano Science and Technology, National Cheng Kung University, Tainan, Taiwan 701, Republic of China
T.S. Chen
Affiliation:
Department of Mechanical Engineering, Center for Micro/Nano Science and Technology, National Cheng Kung University, Tainan, Taiwan 701, Republic of China
*
a) Address all correspondence to this author. e-mail: [email protected]
Get access

Abstract

The relations among the process, microstructure, and nanomechanical properties of cosputtered Ta–Si–N thin films have been investigated. The microstructure evolution and varied hardness and elastic modulus property of Ta–Si–N were influenced by nitrogen flow ratios [FN2% = FN2/(Far + FN2) × 100%] during cosputtering together with phase formation and the composition of films. The microstructure of Ta–Si–N formed at a low 2–10 FN2% was an amorphous-like phase with nanocrystalline grains embedded in an amorphous matrix, while polycrystalline Ta–Si–N was obtained at a high 20–30 FN2%. The cubic TaN phase or (Ta1–x,Six)N solid solution is much easier to form polycrystallites than noncubic Ta5Si3, Ta2Si, and Ta2N phases from grazing incidence x-ray diffractometry results. Amorphous-like Ta–Si–N films had much higher nanohardness, stiffness, elastic recovery percentage, and a closer boundary compared to polycrystalline films. A maximum nanohardness of 15.2 GPa was obtained at 3 FN2%. An increased hardness of polycrystalline films at 20–30 FN2% is attributed to the higher amount of the hard TaN phase.

Keywords

HardnessMicrostructurePhysical vapor deposition (PVD)
Type
Articles
Information
Journal of Materials Research , Volume 23 , Issue 2 , February 2008 , pp. 494 - 499
Copyright
Copyright © Materials Research Society 2007

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1PalDey, S.Deevi, S.C.: Properties of single layer and gradient (Ti,Al)N coatings. Mater. Sci. Eng., A 342, 58 2003CrossRefGoogle Scholar
2Kolawa, E., Chen, J.S., Reid, J.S., Pokela, P.J.Nicolet, M.A.: Tantalum-based diffusion-barriers in Si/Cu VLSI metallizations. J. Appl. Phys. 70, 1369 1991CrossRefGoogle Scholar
3Hubner, R., Hecker, M., Mattern, N., Voss, A., Acker, J., Hoffmann, V., Wetzig, K., Engelmann, H.J., Zschech, E., Heuer, H.Wenzel, C.: Influence of nitrogen content on the crystallization behavior of thin Ta–Si–N diffusion barriers. Thin Solid Films 468, 183 2004CrossRefGoogle Scholar
4Chung, C.K., Chen, T.S., Peng, C.C.Wu, B.H.: Thermal stability of Ta–Si–N nanocomposite thin films at different nitrogen flow ratios. Surf. Coat. Technol. 201, 3947 2006CrossRefGoogle Scholar
5Suresha, S.J., Bhide, R., Jayaram, V.Biswas, S.K.: Processing, microstructure and hardness of TiN/(Ti, Al)N multilayer coatings. Mater. Sci. Eng., A 429, 252 2006CrossRefGoogle Scholar
6Veprek, S., Veprek-Heijman, M.G.J., Karvankova, P.Prochazka, J.: Different approaches to superhard coatings and nanocomposites. Thin Solid Films 476, 1 2005CrossRefGoogle Scholar
7Musil, J.: Hard and superhard nanocomposite coatings. Surf. Coat. Technol. 125, 322 2000CrossRefGoogle Scholar
8Nah, J.W., Choi, W.S., Hwang, S.K.Lee, C.M.: Chemical state of (Ta, Si)N reactively sputtered coating on a high-speed steel substrate. Surf. Coat. Technol. 123, 1 2000CrossRefGoogle Scholar
9Chung, C.K.Su, P.J.: Material characterization and nanohardness measurement of nanostructured Ta–Si–N film. Surf. Coat. Technol. 188–89, 420 2004CrossRefGoogle Scholar
10Chung, C.K.Chen, T.S.: Effect of microstructures on the electrical and optoelectronic properties of nanocrystalline Ta–Si–N thin films by reactive magnetron cosputtering. Scripta Mater. 57, 611 2007CrossRefGoogle Scholar
11Zhu, B., Asaro, R.J., Krysl, P., Zhang, K.Weertman, J.R.: Effects of grain size distribution on the mechanical response of nanocrystalline metals: Part II. Acta Mater. 54, 3307 2006CrossRefGoogle Scholar
12Kumar, K.S., Van Swygenhoven, H.Suresh, S.: Mechanical behavior of nanocrystalline metals and alloys. Acta Mater. 51, 5743 2003CrossRefGoogle Scholar
13Sanjines, R., Benkahoul, M., Sandu, C.S., Schmid, P.E.Levy, F.: Relationship between the physical and structural properties of NbzSiyNx thin films deposited by dc reactive magnetron sputtering. J. Appl. Phys. 98, 123511 2005CrossRefGoogle Scholar
14Oliver, W.C.Pharr, G.M.: An important technique for determining hardness and elastic-modulus using load and displacement sensing indentation experiments. J. Mater. Res. 7, 1564 1992CrossRefGoogle Scholar
15Sneddon, I.N.: The relation between load and penetration in the axisymmetric Boussinesq problem for a punch of arbitrary profile. Int. J. Eng. Sci. 3, 47 1965CrossRefGoogle Scholar
16Li, X.D.Bhushan, B.: A review of nanoindentation continuous stiffness measurement technique and its applications. Mater. Charact. 48, 11 2002CrossRefGoogle Scholar
17JCPDS Nos. 26-0985, 32-1283, 06-0552, 72-127518-1312. International Center for Diffraction Data Newton Square, PA, 1997Google Scholar
18Cullity, B.D.: Elements of X-Ray Diffractions 2nd ed.Addison-Wesley Press Lond 1987 Chaps. 3–4Google Scholar
19Zhang, S., Sun, D., Fu, Y.Q.Du, H.J.: Recent advances of superhard nanocomposite coatings: A review. Surf. Coat. Technol. 167, 113 2003CrossRefGoogle Scholar
20Schiotz, J.Jacobsen, K.W.: A maximum in the strength of nanocrystalline copper. Science 301, 1357 2003CrossRefGoogle ScholarPubMed